Ricoh M099 Manual

1
PE-MF3/PE-P2 Training
Slide 1
M099/M100, M095/M096
Service Training
PE-MF3a/PE-MF3c, PE-P2a/PE-P2c
Version 1.0
This training course provides service technician training for the PE-MF3/PE-P2
series.
The differences between this series and the previous PE-MF2/PE-P1e series are
also explained.

2
PE-MF3/PE-P2 Training
Slide 2
Service Training
M099/M100, M095/M096
Product Overview
This section provides an overview of the machine, and the options that can be
installed.

3
PE-MF3/PE-P2 Training
Slide 3
What Models are there in the Series?
PE-MF3
PE-MF3a (M099)
16 ppm (color and b/w)
DDST (GDI)
Memory: 256 MB
‘4-in-1’ (Print/Copy/Fax/Scan)
PE-MF3c (M100)
20 ppm (color and b/w)
PCL/PS
Memory: 256 MB
‘4-in-1’ (Print/Copy/Fax/Scan)
No hard disk and no optional memory for either model
Difference from PE-MF2: Both models were 20 ppm in the PE-MF2 series, and
optional memory was available for the PE-MF2c.
Print speeds are for A4

4
PE-MF3/PE-P2 Training
Slide 4
What Models are there in the Series?
PE-P2
PE-P2a (M095)
16 ppm (color and b/w)
DDST (GDI)
Memory: 64 MB
PE-P2c (M096)
20 ppm (color and b/w)
PCL/PS
Memory: 256 MB
No hard disk and no optional memory for either model
Difference from PE-P1e: Both models were 20 ppm in the PE-P1e series, and
optional memory was available for both models.
Print speeds are for A4
¾For LT, the speeds are 16.5 and 21 cpm

5
PE-MF3/PE-P2 Training
Slide 5
Appearance – MFP Models
Note that the two models have different color schemes.
PE-MF3a PE-MF3c
These machines have a built-in ADF.

6
PE-MF3/PE-P2 Training
Slide 6
Appearance – Printer Models
Note that the two models have different color schemes.
PE-P2a PE-P2c
No additional notes

7
PE-MF3/PE-P2 Training
Slide 7
Standard Equipment
This equipment is built-in for all models.
35-sheet automatic document feeder (MF models only)
250-sheet paper feed unit
1-sheet bypass feed
Duplex
Ethernet: 10Base-T/100base-TX
USB 2.0
Fax
Memory
PE-MF3a: 256 MB
PE-MF3c: 256 MB
PE-P3a: 64 MB
PE-P3c: 256 MB
No optional memory
No hard disk (built-in or optional) for any model
Duplex can be used for printing and copying. In some earlier models in this
series, duplex could not be used for copying.

8
PE-MF3/PE-P2 Training
Slide 8
Optional Equipment
TK1010 Paper Feed Unit, G849
Available for all models
Also used in the PE-MF1/MF2/P1/P1E series
No optional memory
Some of the previous models in this series also had optional memory.

9
PE-MF3/PE-P2 Training
Slide 9
Product Positioning – MF Model
FY2008
FY2008 FY2009
FY2009 FY2011
FY2011
FY2007
FY2007
PE-MF1a
PE-MF1c
PE-MF1b
3 in 1
GDI
Nov ‘07.
FY2010
FY2010
20ppm
20ppm
16ppm
PE-MF2c
Jan ‘09. 20ppm
PE-MF2b
20ppm
PE-MF3c
Jun ‘11. 20ppm
PE-MF3a
16ppm
4 in 1
GDI
4 in 1
PCL 4 in 1 PCL
4 in 1
GDI
4 in 1
GDI
4 in 1
PCL
Per/ Mid HY/SY Toner
Per SY Toner
No additional notes

10
PE-MF3/PE-P2 Training
Slide 10
Product Positioning – Printer Model
FY2008
FY2008 FY2009
FY2009 FY2011
FY2011
FY2007
FY2007
PE-P1a
PE-P1c
PE-P1b
GDI
Jul ‘07.
FY2010
FY2010
20ppm dn
20ppm n
16ppm n
PE-P1Ec
Feb ‘09.20ppm dn
PE-P1Eb
20ppm n
PE-P2c
Jun ‘11. 20ppm dn
PE-P2a
16ppm dn
MD-P1c
Dec ‘08.25ppm dn
MD-P1b
25ppm n
PCL
PCL PCL
PCL
GDI
PCL
MD-P2c
25ppm dn
Per/ Mid HY/SY Toner
Per SY Toner
Nov ‘10.
PCL (GW CTL)
PCL
GDI
Price
No additional notes

11
PE-MF3/PE-P2 Training
Slide 11
Summary of Differences from Previous Products
PE-MF3 – Specifications
Warm-up time:
PE-MF3c: 30 sec (PE-MF2c: 48 sec)
PE-MF3a: 30 sec (PE-MF1a: 51 sec)
The hot roller has a thin wall, which makes the
warm-up time faster and allows lower energy
consumption.
Typical Energy Consumption (TEC)
PE-MF3a: approx. 2.8kWh (PE-MF1a: 4.5kWh)
PE-MF3c: approx. 3.3kWh (PE-MF2c: 5.9kWh)
Durability
Estimated unit life: This is higher for MF3c (180k
prints) than previous models in this series (90k
prints).
No additional notes

12
PE-MF3/PE-P2 Training
Slide 12
Summary of Differences from Previous Products
PE-MF3 – Features
Operation panel: The following were added
4-line LCD, improved from the previous model (2 line LCD)
USB port, for Scan to USB and PictBridge
ID Card Copy button
Fax Received indicator
Easy-to-see lamps: The operation panel angle is raised so that
users can see the alert lamps even while seated
Economy Color
Provides a slightly lighter output with lower printout cost
Reduced Toner Usage
Motor operation stops during sleep mode recovery
Fax
Internet fax has been added (PE-MF3c only)
Speed Dial: 200 locations (previous model was only 50)
JBIG compression has been added
» This allows a transmission time of 2 seconds per page (previous
maximum speed, with MMR compression, was 3 seconds per page)
Authorized reception and paperless fax reception are new features
for this series
Network
IPv6 supported (not supported in previous models)
No additional notes

13
PE-MF3/PE-P2 Training
Slide 13
Summary of Differences from Previous Products
PE-P2 – Specifications
Auto duplex for all models (PE-P1a: manual duplex only)
Warm-up time
PE-P2c: 30 sec (PE-P1E: 48 sec)
PE-P2a: 30 sec (PE-P1a: 51 sec)
The hot roller has a thin wall, which makes the warm-up
time faster and allows lower energy consumption.
Typical Energy Consumption (TEC)
PE-P2c: 3.1kWh (PE-P1Ec: 4.6kWh)
PE-P2a: 2.3kWh (PE-P1a: 3.2kWh)
Durability
Estimated unit life: This is higher for P2c (180k prints) than
previous models in this series (90k prints).
No additional notes

14
PE-MF3/PE-P2 Training
Slide 14
Summary of Differences from Previous Products
PE-P2 – Features
Operation panel
Easy-to-see lamps: The operation panel angle is raised so
that users can see the alert lamps even while seated
Economy Color
Provides a slightly lighter output with lower printout cost
Reduced Toner Usage
Motor operation stops during sleep mode recovery
Network
IPv6 supported (not supported in previous models)
PictBridge
Supported at the rear USB socket.
SOM (Smart Organizing Monitor)
This is not used. The technician does not need to use a
computer to access service mode. Operation is the same
as the MF models.
No additional notes

15
PE-MF3/PE-P2 Training
Slide 15
Operation Panel – MFP Model
4-line display (previous model: 2 lines)
New features for this series:
USB port, for Scan to USB and PictBridge
ID Card Copy button
Fax Received indicator
Easy-to-see lamps: The operation panel angle is raised so that users can
see the lamps even while seated
ID Card Copy
Button
Fax Received
Indicator Easy-to-see
Lamps
USB Port
ID Card Copy
¾Use for printing 2-sided originals, such as an ID card, on one sheet. One
side of the original is printed on the upper half of the paper and the other
side is printed on the lower half.

16
PE-MF3/PE-P2 Training
Slide 16
Operation Panel – Printer Model
Two-line LCD (same as PE-P1e)
Easy-to-see lamps: The operation panel angle is raised so
that users can see the lamps even while seated
No additional notes

17
PE-MF3/PE-P2 Training
Slide 17
LED Lamps – Comparison with Older Models
PE-P2PE-P1
PE-MF3PE-MF1
No additional notes

18
PE-MF3/PE-P2 Training
Slide 18
AIO Cartridge
The OPC, charge roller, and development unit are all in an AIO
cartridge.
AIO: All-in-one
The cartridge can be removed with one hand.
The cartridges are the same as used in previous models.
See the next slide for details.
No additional notes

19
PE-MF3/PE-P2 Training
Slide 19
Types of AIO (Print) Cartridge
Pe-MF3a, PE-P2a
Starter
» 1 k prints per cartridge
Short Yield
» 2 k prints per cartridge
– Same cartridges as PE-MF1
Pe-MF3c, PE-P2c
Starter
» 1 k prints per cartridge
Short Yield
» 2.5 k prints per cartridge
– Same cartridges as PE-MF2
Long (High Yield) – Pe-MF3c and Pe-P2c only
» 6.5 k prints per cartridge (BK)
» 6.0 k prints per cartridge (CMY)
– Same cartridges as PE-MF2
AIO yield measurements are based on ISO 19798, except for PE-MF3a/P2a,
which is based on 5% 24P/J
Note that different cartridge types are used for the short yield AIO.
¾PE-MF3a/P2a uses the PE-P1/PE-MF1 type AIO. PE-MF3c/P2c uses PE-
P1e/PE-MF2/MD-P1/MD-P2 type AIO.

20
PE-MF3/PE-P2 Training
Slide 20
Other Consumables
Waste Toner Tank
Approximately 25 k prints per tank
» Same tank as previous models
All consumables can be replaced by customers.
The waste toner tank is the same as the one that is used for previous models in
this series.
Waste toner tank yield measurement based on 5%, 3P/J, 50% color ratio
¾Color ratio: 50% means that half the jobs are black-and white, and half are
color
¾Compatible with Pe-P1, Pe-MF1, Pe-MF2, and Md-P1