Ricoh VT2240 User manual

INTRODUCTION
This manual contains detailed instructions on the operation and mainte-
nance of this machine. To get the maximum versatility from this machine, all
operators should carefully read and follow the instructions in this manual.
Please keep this manual in a handy place near the machine.
Please read the next section before using this machine. It contains impor-
tant information related to USER SAFETY and PREVENTING EQUIPMENT
PROBLEMS.
SAFETY INFORMATION
When using your machine, the following safety precautions should always
be followed.
Safety During Operation
In this manual, the following important symbols are used:
$
WARNING:Ignoring this warning could cause serious injury
or even death.
$
CAUTION: Ignoring this caution could cause injury or
damage to property.
Examples Of Indications
$ Symbols $ means a situation that requires you take care.
B Do NOT carry out the operation represented by the symbol > .
This example means "Do not take apart".
C Symbols
●
means you MUST perform this operation.
This example means "You must remove the wall plug".
gold-eeg-1
INTRODUCTION
i

$
WARNINGS:
••Only connect the machine to the power source described on
the inside front cover of this manual. Avoid multi-wiring as
it could cause an electric shock or a fire.
••Avoid using an extension cord. Make sure the wall outlet is
near the machine and freely accessible so that in event of an
emergency it can be unplugged easily.
••Do not damage, break or make any modifications to the
power cord. Do not place heavy objects on it, pull it hard or
bend it more than necessary. These actions could cause an
electric shock or fire.
••Do not remove any covers or screws other than those
specified in this manual. Some parts of the machine are at a
high voltage and could give you an electric shock. When the
machine needs to be checked, adjusted or repaired, contact
your service representative.
••Do not take apart or attempt any modifications to this
machine. There is a risk of fire, electric shock, explosion or
loss of sight.
••If the machine looks damaged or breaks down, smoke is
coming out, there is a strange smell or anything looks
unusual, immediately turn off the main power switch then
unplug the power code from the wall. Do not continue using
the machine in this condition. Contact your service represen-
tative.
••Do not put any metal objects or containers holding water
(e.g. vases, flowerpots, glasses) on the machine. If the
contents fall inside the machine a fire or electric shock could
occur.
••If any metal, liquid or foreign matter falls into the machine,
turn off the main switch and unplug the main power cord.
Contact your service representative. Do not keep using the
machine with a fault or defect.
>
>
B
C
C
>
gold-eeg-1
SAFETY INFORMATION
ii

••Do not plug or unplug the power cord with wet hands or an
electric shock might occur.
$
CAUTIONS:
••When you move the machine, unplug the power cord from
the wall outlet to avoid fire or electric shock.
••When you pull out the plug from the socket, grip the plug to
avoid damaging the cord and causing fire or electric shock.
••Keep the machine away from humidity and dust. A fire or
an electric shock might occur.
••Do not place the machine on an unstable or tilted surface.
If it topples over it could cause injury.
••When the machine will not be used for a long time, unplug
the power cord.
••If you use this machine in a confined space, make sure there
is a continuous air turnover.
••This machine has been tested for safety using this supplier’s
parts and consumable. We recommend you only use these
specified supplies.
>
$
E
>
C
@
C
gold-eeg-1
SAFETY INFORMATION
iii

GUIDE TO COMPONENTS
Machine Exterior
123
5
4
6
7
8
9
10
gold-eeg-2
GUIDE TO COMPONENTS
1

1. Operation panel Operator controls and indicators are located
here. ☛See pages 5 ~ 7.
2. Platen cover Lower this cover over an original before printing.
3. Original table
release lever Use to open the original table unit when installing
the master.
4. Feed roller
pressure lever Use to adjust the contact pressure of the paper
feed roller according to paper thickness.
5. Separation roller
pressure lever Use to adjust the separation roller pressure to
prevent double feed.
6. Paper feed side
plates Use to prevent paper skew.
7. Paper feed table Set paper on this table for printing.
8. Side plate fine
adjusting dial Use to shift the paper feed table sideways.
9. Front cover Open to access to the inside of the machine.
10. Plate Flip over when you use One Touch Class func-
tion. ☛See page 47.
gold-eeg-2
GUIDE TO COMPONENTS
2

Machine Interior
123 4
5
6
7
8
9
10
11
12
13
14
15
gold-eeg-2
GUIDE TO COMPONENTS
3

1. Document feeder
(Option) Original inserted into the document feeder are in-
dividually and automatically fed onto and re-
moved from the exposure glass. ☛See page 82.
2. Master eject unit
open button Press to remove misfed paper or a misfed mas-
ter.
3. Master cut button Press this button to cut the master leading edge
after installing a new master roll.
4. Pressure release
lever Use to install the master roll.
5. Drum rotation
button Press to rotate the drum unit.
6. Drum unit lock
lever Lift to unlock and pull out the drum unit.
7. Drum unit The master is wrapped around this unit.
8. Ink holder Set the ink cartridge in this holder.
9. Main switch Use to turn the power on or off.
10. Paper delivery table Completed prints are delivered here.
11. Small size paper
delivery end plate Use to align the leading edge of prints that are
A4, 81/2" x 11" or smaller.
12. Paper delivery end
plate Use to align the leading edge of prints larger
than A4, 81/2" x 11".
13. Paper delivery side
plate Use to align the prints on the paper delivery table.
14. Wing guides When printing on thin or small size paper, lift
these guides. ☛See page 15.
15. Master eject
container cover Open when removing the master eject box.
❐Other options: Color Drums (red, blue, green, brown, yellow, purple, navy,
maroon, orange and teal)
Tape Dispenser
Key Counter
Cabinet
gold-eeg-2
GUIDE TO COMPONENTS
4

Operation Panel
Keys
123456
78910 11
12 13 14 16 17
15 18 19
20 21
1. Economy/Tint key
☛See pages 42 ~ 44.
2. Skip Feed key
☛ See page 71.
3. Image Density key
☛ See page 23.
4. Paste Shadow Erase key
☛See page 36.
5. Auto Cycle key
☛See page 45.
6. Master Making/Print key
Press to select Master Making or
Print mode.
7. Security key
☛See page 79.
8. Quality Start key
☛See page 80.
9. SP mode key
☛See page 94.
10. Edge Erase key
☛See page 34.
11. Edge Erase/Center Erase key
☛See page 31.
12. 13. 14. CS mode keys
☛See pages 97 ~ 101.
15. 16. Scroll keys
Press to select size and direction
of paper or original in Edge
Erase/Center Erase and Edge
Erase function.
Press to select the mode in Serv-
ice Program mode.
17. Type of Original key
☛See page 40.
18. Reduce key
☛See page 27.
19. Enlarge key
☛See page 29.
gold-eeg-2
GUIDE TO COMPONENTS
5

20. Full Size key
Press to make full size prints.
21. Combine 2 Originals key
☛See page 63.
22. Image Position keys
☛See page 21.
23. Reset key
Press to reset the error indicators.
24. Program Class key
☛See page 47.
25. Program key
☛See page 73.
26. Proof key
Press to make proof prints.
27. Clear Modes key
Press to cancel all previously en-
tered settings.
28. Speed keys
☛See page 24.
29. Lower key
Press to lower the paper feed ta-
ble.
30. Clear key
Press to change the number set.
31. Number keys
Press to enter the number of
prints and data.
32. Enter key
Press to input data into memory.
33. Start key
Press to start making of a master
or printing.
34. Stop key
Press to stop the machine opera-
tion.
22 23 24 25 26 27
28 29 30 31 32 33 34
gold-eeg-2
GUIDE TO COMPONENTS
6

Indicators
123456
1. Error indicators
These indicators are lit when a
non-standard condition occurs
within the machine. ☛See page
128.
2. Guidance Display
Press to stop the machine opera-
tion.
3. Master Making indicator
This indicator is lit when Master
Making mode is selected.
4. Print indicator
This indicator is lit when Print
mode is selected.
5. Speed indicators
These indicators show the printing
speed that is selected. ☛See
page 24.
6. Color Drum indicator
This indicator is lit when the op-
tional color drum unit is set. ☛
See page 88.
gold-eeg-2
GUIDE TO COMPONENTS
7