Riello RLS 68/M MX FS1 Quick start guide

20148266 (4) - 01/2022
Installation, use and maintenance instructions
Dual fuel light oil/ gas burners
Progressive two-stage or modulating operation gas side/
two-stage light oil side
CODE MODEL TYPE
20147784 RLS 68/M MX FS1 779T
20147785 RLS 68/M MX FS1 779T
20147786 RLS 120/M MX FS1 780T
20147788 RLS 120/M MX FS1 780T
GB

Translation of the original instructions

1 20148266
GB
Contents
1 Declarations................................................................................................................................................................................ 3
2 Information and general warnings............................................................................................................................................ 5
2.1 Information about the instruction manual .................................................................................................................... 5
2.2 Guarantee and responsibility....................................................................................................................................... 6
3 Safety and prevention................................................................................................................................................................ 7
3.1 Introduction.................................................................................................................................................................. 7
3.2 Personnel training ....................................................................................................................................................... 7
4 Technical description of the burner ......................................................................................................................................... 8
4.1 Burner designation ...................................................................................................................................................... 8
4.2 Models available.......................................................................................................................................................... 8
4.3 Burner categories - Countries of destination ............................................................................................................... 9
4.4 Technical data............................................................................................................................................................. 9
4.5 Electrical data.............................................................................................................................................................. 9
4.6 Packaging - Weight ................................................................................................................................................... 10
4.7 Maximum dimensions................................................................................................................................................ 10
4.8 Firing rate .................................................................................................................................................................. 11
4.9 Test boiler.................................................................................................................................................................. 11
4.10 Commercial boilers.................................................................................................................................................... 12
4.11 Burner equipment...................................................................................................................................................... 12
4.12 Burner description ..................................................................................................................................................... 13
4.13 Electrical panel description........................................................................................................................................ 14
4.14 Control box RFGO-A22............................................................................................................................................. 15
4.15 Servomotor (SQN31...).............................................................................................................................................. 16
4.16 Calibration of the thermal relay ................................................................................................................................. 17
4.17 Motor rotation ............................................................................................................................................................ 17
5 Installation ................................................................................................................................................................................ 18
5.1 Notes on safety for the installation ............................................................................................................................ 18
5.2 Handling .................................................................................................................................................................... 18
5.3 Preliminary checks .................................................................................................................................................... 18
5.4 Operating position ..................................................................................................................................................... 19
5.5 Preparing the boiler................................................................................................................................................... 19
5.6 Securing the burner to the boiler............................................................................................................................... 20
5.7 Electrode position...................................................................................................................................................... 20
5.8 Choice of nozzles for the 1st and 2nd stage ............................................................................................................. 21
5.9 Nozzle installation ..................................................................................................................................................... 22
5.10 Combustion head adjustment.................................................................................................................................... 23
5.11 Light oil supply........................................................................................................................................................... 24
5.12 Gas supply ................................................................................................................................................................ 27
5.13 Electrical connections................................................................................................................................................ 30
6 Start-up, calibration and operation of the burner ................................................................................................................. 31
6.1 Notes on safety for the first start-up .......................................................................................................................... 31
6.2 Servomotor adjustment ............................................................................................................................................. 31
6.3 Adjustments prior to ignition (light oil) ....................................................................................................................... 31
6.4 Burner start-up (light oil)............................................................................................................................................ 32
6.5 Burner ignition (light oil)............................................................................................................................................. 32
6.6 Burner adjustment (light oil) ...................................................................................................................................... 32
6.7 Adjustments prior to ignition (gas)............................................................................................................................. 33
6.8 Burner start-up (gas) ................................................................................................................................................. 33

20148266 2
GB
Contents
6.9 Burner ignition (gas)...................................................................................................................................................33
6.10 Burner adjustment (gas) ............................................................................................................................................34
6.11 Change of fuel............................................................................................................................................................35
6.12 Pressure switch adjustment .......................................................................................................................................36
6.13 Operation sequence of the burner (gas) ....................................................................................................................37
6.14 Final checks (with burner operating)..........................................................................................................................38
7 Maintenance ..............................................................................................................................................................................39
7.1 Notes on safety for the maintenance .........................................................................................................................39
7.2 Maintenance programme ...........................................................................................................................................39
7.3 Opening the burner ....................................................................................................................................................42
7.4 Closing the burner......................................................................................................................................................42
8 LED indicator and special function.........................................................................................................................................43
8.1 Description of LED lamps ..........................................................................................................................................43
8.2 Check mode function .................................................................................................................................................43
8.3 Flame control lock-out or emergency stop condition .................................................................................................43
8.4 LED lamps: burner operating status ..........................................................................................................................44
9 Problems - Causes - Remedies signalled by LED indicators ...............................................................................................45
A Appendix - Accessories ...........................................................................................................................................................50
B Appendix - Electrical panel layout...........................................................................................................................................51

3 20148266
GB
Declarations
1 Declarations
Declaration of Conformity in accordance with ISO / IEC 17050-1
Manufacturer: RIELLO S.p.A.
Address: Via Pilade Riello, 7
37045 Legnago (VR) Italy
Product: Dual fuel Light Oil/Gas Burner
Model: RLS 68/M MX - RLS 120/M MX
These products are in compliance with the following Technical Standards:
EN 676
EN 267
EN 12100
and according to the European Directives:
GAR 2016/426/EU Gas Devices Regulation
MD 2006/42/CE Machine Directive
LVD 2014/35/EU Low Voltage Directive
EMC 2014/30/EU Electromagnetic Compatibility
Such products are marked as indicated below:
The quality is guaranteed by a quality and management system certified in accordance with ISO 9001:2015.
CE 0085 BP 0175
Manufacturer's Declaration
RIELLO S.p.A. declares that the following products comply with the NOx emission limits specified by German standard
“1. BImSchV revision 26.01.2010”.
Product Type Model Output
Dual fuel Light Oil/Gas Burner 779T RLS 68/M MX 200 - 860 kW
780T RLS 120/M MX 300 - 1200 kW
Legnago, 03.05.2021 Research & Development Director
RIELLO S.p.A. - Burner Department
Mr. F. Maltempi

20148266 4
GB
Declarations
Declaration of Conformity A.R. 8/1/2004 & 17/7/2009 – Belgium
Manufacturer: RIELLO S.p.A.
37045 Legnago (VR) Italy
Tel. ++39.0442630111
www.riello.com
Distributed by: RIELLO NV
VAN MARCKE HQ
LAR Blok Z 5,
B-8511 Kortrijk (Aalbeke) Belgio
Tel. [phone]
e-mail: [email protected]
URL. www.vanmarcke.com
This document certifies that the series of devices specified below is in compliance with the model described in the EC Declaration of
Conformity and has been manufactured and distributed in compliance with the requirements defined in the Legislative Decree of
January 8th 2004 and July 17th 2009.
Type of product: Dual fuel Light Oil/Gas Burner
Model: RLS 68/M MX - RLS 120/M MX
Regulation applied: EN 267/676 and A.R. of January 8th 2004 - July 17th 2009
Controlling organisation: TÜV Industrie Service GmbH
TÜV SÜD Gruppe
Ridlerstrase, 65
80339 München DEUTSCHLAND
Values measured: OIL GAS
RLS 68/M MX CO max: 12 mg/kWh CO max: 8 mg/kWh
Max. NOx: 110 mg/kWh NOx max: 70 mg/kWh
RLS 120/M MX CO max: 6 mg/kWh CO max: 7 mg/kWh
Max. NOx: 130 mg/kWh NOx max: 64 mg/kWh

5 20148266
GB
Information and general warnings
2.1 Information about the instruction manual
2.1.1 Introduction
The instruction manual supplied with the burner:
is an integral and essential part of the product and must not
be separated from it; it must therefore be kept carefully for
any necessary consultation and must accompany the burner
even if it is transferred to another owner or user, or to
another system. If the manual is lost or damaged, another
copy must be requested from the Technical Assistance
Centre of the area;
is designed for use by qualified personnel;
offers important indications and instructions relating to the
installation safety, start-up, use and maintenance of the
burner.
Symbols used in the manual
In some parts of the manual you will see triangular DANGER
signs. Pay great attention to these, as they indicate a situation of
potential danger.
2.1.2 General dangers
The dangers can be of 3 levels, as indicated below.
2.1.3 Other symbols
Abbreviations used
Ch. Chapter
Fig. Figure
Page Page
Sec. Section
Tab. Table
2 Information and general warnings
DANGER
Maximum danger level!
This symbol indicates operations which, if not
carried out correctly, cause serious injury, death
or long-term health risks.
ATTENTION
This symbol indicates operations which, if not
carried out correctly, may cause serious injury,
death or long-term health risks.
CAUTION
This symbol indicates operations which, if not
carried out correctly, may cause damage to the
machine and/or injury to people.
DANGER
DANGER: LIVE COMPONENTS
This symbol indicates operations which, if not
carried out correctly, lead to electric shocks with
lethal consequences.
DANGER: FLAMMABLE MATERIAL
This symbol indicates the presence of flammable
materials.
DANGER: BURNING
This symbol indicates the risks of burns due to
high temperatures.
DANGER: CRUSHING OF LIMBS
This symbol indicates the presence of moving
parts: danger of crushing of limbs.
WARNING: MOVING PARTS
This symbol indicates that you must keep limbs
away from moving mechanical parts; danger of
crushing.
DANGER: EXPLOSION
This symbol signals places where an explosive
atmosphere may be present. An explosive
atmosphere is defined as a mixture - under
atmospheric conditions - of air and flammable
substances in the form of gases, vapours, mist or
dust in which, after ignition has occurred,
combustion spreads to the entire unburned
mixture.
PERSONAL PROTECTION EQUIPMENT
These symbols indicate the equipment that must
be worn and kept by the operator for protection
against threats against safety and/or health while
at work.
OBLIGATION TO ASSEMBLE THE COVER
AND ALL THE SAFETY AND PROTECTION
DEVICES
This symbol signals the obligation to reassemble
the cover and all the safety and protection devices
of the burner after any maintenance, cleaning or
checking operations.
ENVIRONMENTAL PROTECTION
This symbol gives indications for the use of the
machine with respect for the environment.
IMPORTANT INFORMATION
This symbol indicates important information that
you must bear in mind.
This symbol indicates a list.

20148266 6
GB
Information and general warnings
2.1.4 Delivery of the system and the instruction
manual
When the system is delivered, it is important that:
the instruction manual is delivered to the user by the system
manufacturer, with the recommendation to keep it in the
room where the heat generator is to be installed.
The instruction manual shows:
– the serial number of the burner;
– the address and telephone number of the nearest
Assistance Centre;
The system supplier must carefully inform the user about:
– the use of the system;
– any further tests that may be required before activating the
system;
– maintenance, and the need to have the system checked at
least once a year by a representative of the manufacturer
or another specialised technician.
To ensure a periodic check, the manufacturer
recommends the drawing up of a Maintenance Contract.
2.2 Guarantee and responsibility
The manufacturer guarantees its new products from the date of
installation, in accordance with the regulations in force and/or the
sales contract. At the moment of the first start-up, check that the
burner is integral and complete.
In particular, the rights to the guarantee and the responsibility will
no longer be valid, in the event of damage to things or injury to
people, if such damage/injury was due to any of the following
causes:
incorrect installation, start-up, use and maintenance of the
burner;
improper, incorrect or unreasonable use of the burner;
intervention of unqualified personnel;
carrying out of unauthorised modifications on the equipment;
use of the burner with safety devices that are faulty,
incorrectly applied and/or not working;
installation of untested supplementary components on the
burner;
powering of the burner with unsuitable fuels;
faults in the fuel supply system;
continuation of use of the burner when a fault has occurred;
repairs and/or overhauls incorrectly carried out;
modification of the combustion chamber with inserts that
prevent the regular development of the structurally
established flame;
insufficient and inappropriate surveillance and care of those
burner components most likely to be subject to wear and
tear;
use of non-original components, including spare parts, kits,
accessories and optional;
force majeure.
The manufacturer furthermore declines any and every
responsibility for the failure to observe the contents of this
manual.
.........................................................................................
.........................................................................................
.........................................................................................
.........................................................................................
ATTENTION
Failure to observe the information given in this
manual, operating negligence, incorrect
installation and carrying out of non authorised
modifications will result in the annulment by the
manufacturer of the guarantee that it supplies with
the burner.

7 20148266
GB
Safety and prevention
3.1 Introduction
The burners have been designed and built in compliance with
current regulations and directives, applying the known technical
safety rules and envisaging all the potential danger situations.
It is necessary, however, to bear in mind that the imprudent and
clumsy use of the equipment may lead to situations of death risk
for the user or third parties, as well as the damaging of the burner
or other items. Inattention, thoughtlessness and excessive
confidence often cause accidents; the same applies to tiredness
and sleepiness.
It is a good idea to remember the following:
The burner must only be used as expressly described. Any
other use should be considered improper and therefore
dangerous.
Specifically:
it can be applied to boilers operating with water, steam,
diathermic oil, and to other uses expressly named by the
manufacturer;
the type and pressure of the fuel, the voltage and frequency of the
electrical power supply, the minimum and maximum deliveries for
which the burner has been regulated, the pressurisation of the
combustion chamber, the dimensions of the combustion
chamber and the ambient temperature must all be within the
values indicated in the instruction manual.
Modification of the burner to alter its performance and
destinations is not allowed.
The burner must be used in exemplary technical safety
conditions. Any disturbances that could compromise safety
must be quickly eliminated.
Opening or tampering with the burner components is not
allowed, apart from the parts requiring maintenance.
Only those parts envisaged by the manufacturer can be
replaced.
3.2 Personnel training
The user is the person, body or company that has acquired the
machine and intends to use it for the specific purpose. He is
responsible for the machine and for the training of the people
working around it.
The user:
undertakes to entrust the machine exclusively to suitably
trained and qualified personnel;
undertakes to inform his personnel in a suitable way about
the application and observance of the safety instructions.
With that aim, the user undertakes to ensure that everyone
knows the use and safety instructions for his own duties;
Personnel must observe all the danger and caution
indications shown on the machine.
Personnel must not carry out, on their own initiative,
operations or interventions that are not within their province.
Personnel must inform their superiors of every problem or
dangerous situation that may arise.
The assembly of parts of other makes, or any modifications,
can alter the characteristics of the machine and hence
compromise operating safety. The manufacturer therefore
declines any and every responsibility for any damage that
may be caused by the use of non-original parts.
In addition:
3 Safety and prevention
ATTENTION
The manufacturer guarantees safety and proper
operation only if all burner components are intact
and correctly positioned.
must take all the measures necessary to
prevent unauthorised people gaining access
to the machine;
the user must inform the manufacturer if
faults or malfunctioning of the accident
prevention systems are noticed, along with
any presumed danger situation;
personnel must always use the personal
protective equipment envisaged by legislation
and follow the indications given in this
manual.

20148266 8
GB
Technical description of the burner
4.1 Burner designation
4.2 Models available
Tab. A
4 Technical description of the burner
Designation Voltage Start-up Code
RLS 68/M MX 3/400/50 Direct 20147784 - 20147785
RLS 120/M MX 3/400/50 Direct 20147786 - 20147788
Series: R
Size
Fuel: Natural gas
Light oil
Light oil / Methane
Adjustment:
Flame control system:
FS1
FS2
Standard (1 stop every 24 h)
Electrical supply of the system:
3/400/50
3/230/50
Voltage of auxiliaries:
230/50/60
110/50/60
RLS 68 MTC
Emission: ... Class 1 EN267 - EN676
MY Class 1 EN267 - Class 3 EN676
BLU Class 3 EN267 - EN676
MX Class 2 EN267
Class 3 EN676
FS1 3/400/50 230/50
BASIC DESIGNATION
EXTENDED DESIGNATION
MX
3N / 400V / 50Hz
3 / 230V / 50Hz
230V / 50-60Hz
110V / 50-60Hz
Heavy oil
E Electronic cam
EV Electronic cam and variable speed (with Inverter)
P Proportional air/gas valve
BP Two stage (light oil) / Proportional valve (gas)
M Mechanical cam
S
L
LS
N
Head: TC Standard head
TL Extended head
Continuous operation only with the use of a flame detection
electrode (ionisation)

9 20148266
GB
Technical description of the burner
4.3 Burner categories - Countries of destination
Tab. B
4.4 Technical data
Tab. C
(1) Reference conditions: Ambient temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0 m a.s.l.
(2) Pressure at test point 5)(Fig. 6) with zero pressure in combustion chamber and at maximum burner output.
(3) Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum output. The sound
power is measured using the "Free Field" method, required by EN 15036 standard, and according to an “Accuracy: Category 3” measurement, as
described in EN ISO 3746.
4.5 Electrical data
Tab. D
Country of destination Gas category
SE - FI - AT - GR - DK - ES - GB - IT - IE - PT - IS - CH - NO I2H
DE I2ELL
NL I2L - I2E - I2(43.46 ÷ 45.3 MJ/m3(0°C))
FR I2Er
BE I2E(R)B
LU - PL I2E
Model RLS 68/M MX RLS 120/M MX
Output (1)
Delivery (1)
2nd stage
min - max
kW
kg/h
350 - 860
30 - 73
600 - 1200
50 - 101
1st stage
min
kW
kg/h
200
17
300
25
Fuels Light oil, max. viscosity at 20 °C: 6 mm2/s (1.5 °E - 6 cSt)
Natural gas: G20 (methane gas) - G21 - G22 - G23 - G25
Operation – Intermittent FS1(min. 1 stop in 24 hours) /Continuous FS2
– Oil: two-stage (high and low flame) and one-stage (all - nothing)
– Gas: progressive two-stage or modulating by kit (see ACCESSORIES)
Nozzles number 2
Standard applications Boilers: water, steam, diathermic oil
Ambient temperature °C 0 - 40
Combustion air temperature °C max 60
Pump output (at 20 bar)
pressure range
fuel temperature
kg/h
bar
°C max
220
10 - 20
60
Noise levels (2) Sound pressure
Sound power dB(A) 76 87
79
90
Weight kg 70 76
Model RLS 68/M MX RLS 120/M MX
Main electrical supply 3 ~ 230-400V - 50Hz +/-10%
Auxiliary circuit electrical supply 1N ~ 230V - 50Hz
Fan motor IE3 rpm
V
W
A
2890
220-240/380-415
1500
5.9 / 3.4
2890
220-240/380-415
2200
8 / 4.6
Pump motor IE3 V
W
A
µF
230
550
3.6
25
Ignition transformer V1 - V2
I1 - I2
230 V - 2 x 5 kV
1.9 A - 30 mA
Max. absorbed electric power W2900 3700
Protection level IP 44

20148266 10
GB
Technical description of the burner
4.6 Packaging - Weight
Package dimensions and weight are indicated in Tab. E.
Tab. E
4.7 Maximum dimensions
The dimensions of the burner are given in Fig. 2.
Bear in mind that inspection of the combustion head requires the
burner to be opened and the rear part turned on the hinge.
The maximum dimensions of the open burner are indicated by
the L and R positions.
The l position is reference for the refractory thickness of the boiler
door.
Tab. F
(*) Blast tube: short-long
Model A B C Kg
RLS 68/M MX 1400 645 975 115
RLS 120/M MX 1400 645 975 120
Fig. 1
D36
mm B C D E F G H I* - I (1) L M N P T - T (1) U - U (1)
RLS 68/M MX 214 134 189 430 2” 296 555 200-335 691 395 221 840 260-395 1161-1300
RLS 120/M MX 214 134 189 430 2” 338 555 200-335 733 395 221 840 260-395 1161-1300
P
T(1)
T
I(1)*
I*B
D
E
N
F
C
MG
L
H
U-U(1)
Fig. 2
20152201

11 20148266
GB
Technical description of the burner
4.8 Firing rate
During operation, burner output varies between:
Maximum output
The minimum output must not be lower than the minimum
limit of the diagram
RLS 68/M MX = 200 kW
RLS 120/M MX = 300 kW
4.9 Test boiler
The firing rates were obtained in special test boilers, according to
EN 676 standard.
In (Fig. 4) you can see the diameter and length of the test
combustion chamber.
Example:
Output 650 kW - diameter 60 cm
length 2 m
MODULATING RATIO
The modulating ratio, obtained in the test boilers, according to
standard (EN 676 for gas, EN 267 for light oil), is of
– 3 : 1 (gas);
– 2 : 1 (light oil).
In case of gas operation, it is possible to use the burner with a
different modulating ratio according to the application; for further
information contact the manufacturer.
ATTENTION
The firing rate value (Fig. 3) has been obtained
considering an ambient temperature of 20 °C, an
atmospheric pressure of 1013 mbar (approx. 0 m
a.s.l.), and with the combustion head adjusted as
shown on page 23.
Fig. 3
Thermal power - kW
Pressure in the chamber
pressure - mbar
Pressure in the chamber
pressure - mbar
Thermal power - kW
20185206
Fig. 4
Combustion chamber
length - m
D715

20148266 12
GB
Technical description of the burner
4.10 Commercial boilers
Burners are suitable for operating on both flame inversion boilers
(*) as well as on boilers with a combustion chamber with run-off
from the bottom (three flue passes) on which the best results for
low NOxemissions are obtained.
The boiler front door maximum thickness must not exceed 250
mm (Fig. 5).
Although combination is guaranteed when boiler has a CE type-
approval, preliminary tests are recommended for boilers or
furnaces having a combustion chamber size much different than
the one specified in the diagram (Fig. 4).
(*) For flame inversion boilers, a kit is available to reduce the CO,
if necessary.
4.11 Burner equipment
Flange for gas train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Seal for flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Screws M10x35 to fix the gas flange . . . . . . . . . . . . . . . . . No. 4
Thermal flange gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Screws M12x35 to fix the burner flange to the boiler . . . . . No. 4
Flexible hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 2
Fittings for flexible hoses . . . . . . . . . . . . . . . . . . . . . . . . . . No. 2
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 2
Instruction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. 1
Fig. 5
250 mm MAX
D1079

13 20148266
GB
Technical description of the burner
4.12 Burner description
1 Flame stability disc
2 Ignition electrodes
3 Combustion head
4 Gas pressure test point and head fixing screw
5 Screws to secure fan to pipe coupling
6 Pump motor
7Pump
8 Slide bars for opening the burner and inspecting the
combustion head
9 Electrical control box with lockout pilot light and reset button
10 Air damper
11 Air inlet to fan
12 Gas input pipe
13 Air pressure test point
14 Screw for combustion head adjustment
15 Pipe coupling with flange for fixing to the boiler and the gas
butterfly valve
16 Maximum gas pressure switch
17 Safety valve
18 Servomotor controlling the gas butterfly valve and the air
damper, by means of a variable profile cam mechanism.
When the burner is not operating the air damper is fully
closed in order to reduce heat dispersion from the boiler due
to the flue draught, which draws air from the fan suction
inlet.
19 Fan motor
20 Extensions for slide bars 8)
21 1st and 2nd stage valves
22 Flame inspection window
Fig. 6
20159599

20148266 14
GB
Technical description of the burner
4.13 Electrical panel description
1 Ignition transformer
2 A switch for:
automatic-manual-off operation
A button for:
output increase - decrease
3 Motor contactor and thermal relay with reset button
4 Bracket for application of RWF kit
5 Filter to protect against radio disturbance
6 Terminal board for electric connection
7 Cable grommets for external connections (to be carried out
by the installer)
8 Air pressure switch (differential type)
9 Control box base
10 Oil - gas switch
11 Flame sensor
12 Relay
13 Relay
NOTE
Burner lockout may occur:
control box lockout: if the control box 9)(Fig. 6) push-button
lights up, it indicates that the burner is in lockout.
Press the push button to reset.
4
5
6
7910
11
1
2
3
812
13
Fig. 7
20159603

15 20148266
GB
Technical description of the burner
4.14 Control box RFGO-A22
Important notes
All interventions (assembly and installation operations,
assistance, etc.) must be carried out by qualified personnel.
Before modifying the wiring in the control box connection
area, fully disconnect the system from the power supply
(omnipolar separation).
Protection against electrocution from the control box and all
connected electric components is obtained with the correct
assembly.
Before any intervention (assembly and installation
operations, assistance, etc.), ensure the wiring is in order
and that the parameters are correctly set, then make the
safety checks.
Falls and collisions can negatively affect the safety
functions. In this case, the control box must not be operated,
even if it displays no evident damage.
For safety and reliability, comply with the following
instructions:
– avoid conditions that can favour the development of
condensate and humidity. Otherwise, before switching on
again, make sure that the entire control box is perfectly dry!
– Static charges must be avoided since they can damage the
control box’s electronic components when touched.
Use
The control box is a control and supervision system of medium
and large capacity forced draught burners for intermittent
operation (at least one controlled shutdown every 24 hours).
Installation notes
• Make sure that the electrical wiring inside the boiler complies
with national and local safety regulations.
• Do not confuse the powered conductors with the neutral
ones.
• Ensure that spliced wires cannot get into contact with
neighbouring terminals. Use adequate ferrules.
• Arrange the H.V. ignition cables separately, as far as
possible from the control box and the other cables.
• When wiring the unit, make sure that AC 230 V mains voltage
cables are run strictly separate from extra low-voltage cables
to avoid risks of electrical shock hazard.
Technical data
Tab. G
Electrical wiring of the flame detector
It is important for signal transmission to be almost totally free
of any disturbances or loss:
• Always separate the detector cables from the other cables:
– The capacitive reactance of the line reduces the size of the
flame signal.
– Use a separate cable.
• Respect the allowed cable lengths.
• The ionisation probe is not protected against the risk of
electrocution. When connected to the electricity supply, the
ionisation probe must be protected against any accidental
contact.
• Position the ignition electrode and the ionisation probe so
that the ignition spark cannot form an arc on the probe (risk
of electric overcharge).
ATTENTION
To avoid accidents, material or environmental
damage, observe the following instructions!
The control box is a safety device! Avoid opening
or modifying it, or forcing its operation. The
Manufacturer cannot assume any responsibility
for damage resulting from unauthorised work!
Mains voltage AC 230 V -15% / +10%
Mains frequency 50 / 60 Hz
Primary fuse (external) Refer to the electric
system
Weight approx. 1.1 kg
Power absorption approx. AC 7 VA
Protection level IP40
Safety class II
Environmental conditions
Operation
Climatic conditions
Mechanical conditions
Temperature range
Humidity
DIN EN 60721-3-1
Class 1K2
Class 1M2
-40...+60°C
< 90% RH (non-condensing)
Fig. 8
20152163

20148266 16
GB
Technical description of the burner
4.15 Servomotor (SQN31...)
Important notes
All interventions (assembly and installation operations,
assistance, etc.) must be carried out by qualified personnel.
Before modifying the wiring in the connection area of the
servomotor, fully disconnect the burner control device from
the power supply (omnipolar separation).
To avoid the risk of electrocution, protect the connection
terminals in a suitable manner and correctly fix the cover.
Check the wiring is in order.
Falls and collisions can negatively affect the safety
functions. In this case, the servomotor must not be operated,
even if it displays no evident damage.
Assembly notes
• Check the relevant national safety standards are respected.
• When assembling the servomotor and connecting the
damper, the gears can be disengaged by means of a lever,
allowing the drive shaft to be easily adjusted in both
directions of rotation.
Technical data
Tab. H
ATTENTION
To avoid accidents, material or environmental
damage, observe the following instructions!
Avoid opening, modifying or forcing the
actuators.
Operating voltage AC 220...240 V - 15% / +10%
AC 100...110 V - 15% / +10%
Mains frequency 50...60 Hz 6%
Switching capacity of
auxiliary devices and
limit switches
10 (3) A, AC 24...250 V
Angle
positioning
up to 160° (full scale)
Assembly position option
Protection level IP 54, DIN 40050
Safety class I
Weight approx. 0.8 kg
Actuator motor synchronous motor
Power absorption 6.5 VA
Environmental conditions:
Operation
Climatic conditions
Mechanical conditions
Temperature range
Humidity
DIN EN 60 721-3-1
Class 1K2
Class 1M2
-20...+60°C
< 95% RH
Fig. 9
20160309

17 20148266
GB
Technical description of the burner
4.16 Calibration of the thermal relay
The thermal relay (Fig. 10) serves to avoid damage to the motor
due to an excessive absorption increase or if a phase is missing.
For calibration 2), refer to the table indicated in the electrical
layout (electrical wiring by the installer).
To reset, in case of thermal relay activation, press the "RESET"
button 1). The button “STOP” 3) opens the NC contact (95-96)
and stops the motor. Insert a screwdriver in the window “TEST/
TRIP” 4) and move it in the arrow direction (to the right) to carry
out the thermal relay test.
4.17 Motor rotation
As soon as the burner starts, place yourself in front of the cooling
fan of the fan motor and check that it turns anticlockwise
(Fig. 11).
If this is not the case:
put the switch of the burner to “0” (off) and wait until the
control box carries out the switching off phase.
Invert the phases on the three-phase motor power supply.
ATTENTION
The automatic reset can be dangerous.
This operation is not foreseen in the burner
operation.
12
3
MAN
AUTO
STOP
NO
98 97 96 95
RESET
NC
4
TEST/TRIP
Fig. 10
D8685
DANGER
Disconnect the electrical supply from the burner
by means of the system main switch.
20162359
Fig. 11

20148266 18
GB
Installation
5.1 Notes on safety for the installation
After carefully cleaning all around the area where the burner is to
be installed, and arranging for the environment to be illuminated
correctly, proceed with the installation operations.
5.2 Handling
The burner packaging includes a wooden platform, it is therefore
possible to handle the burner (still packaged) with a pallet truck
or fork lift truck.
5.3 Preliminary checks
Checking the consignment
Checking the characteristics of the burner
Check the identification label of the burner, showing:
the model (A) (Fig. 12) and type of burner (B);
the year of manufacture, in cryptographic form (C);
the serial number (D);
the data for electrical supply and the protection level (E);
the absorbed electrical power (F);
the types of gas used and the relative supply pressures (G);
the data of the burner's minimum and maximum output
possibilities (H) (see Firing rate).
Warning. The burner output must be within the firing rate of
the boiler;
the category of the appliance/countries of destination (I).
light oil maximum viscosity (L).
5Installation
DANGER
All the installation, maintenance and disassembly
operations must be carried out with the electricity
supply disconnected.
ATTENTION
The installation of the burner must be carried out
by qualified personnel, as indicated in this manual
and in compliance with the standards and
regulations of the laws in force.
DANGER
The combustion air inside the boiler must be free
from hazardous mixes (e.g.: chloride, fluoride,
halogen); if present, it is highly recommended to
carry out cleaning and maintenance more
frequently.
ATTENTION
Burner handling operations can be highly
dangerous if not carried out with the greatest
attention: distance unauthorised personnel, check
integrity and suitability of the means available.
Check also that the area in which you are working
is empty and that there is an adequate escape
area (i.e. a free, safe area to which you can
quickly move if the burner should fall).
During handling, keep the load at no more than
20-25 cm from the ground.
After positioning the burner near the installation
point, correctly dispose of all residual packaging,
separating the various types of material.
CAUTION
Before proceeding with the installation operations,
carefully clean all around the area where the
burner will be installed.
CAUTION
After removing all the packaging, check the
integrity of the contents. In the event of doubt, do
not use the burner; contact the supplier.
The packaging elements (wooden cage or
cardboard box, nails, clips, plastic bags, etc.)
must not be abandoned as they are potential
sources of danger and pollution; they should be
collected and disposed of in the appropriate
places.
ATTENTION
A burner label that has been tampered with,
removed or is missing, along with anything else
that prevents the definite identification of the
burner makes any installation or maintenance
work difficult
R.B.L.
GAS- KAASU
GAZ- AEPIO
0085
RIELLOS.p.A.
I-37045 Legnago (VR)
CE
HEIZÖLFUEL
Fig. 12
D9243
ABC
EDF
HG
GH
I
L