Rigol DS2000 Series User manual

RIGOL
Quick Guide
DS2000 Series Digital Oscilloscope
Mar. 2012
RIGOL Technologies, Inc
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
I
Guaranty and Declaration
Copyright
© 2012 RIGOL Technologies, Inc. All Rights Reserved.
Trademark Information
RIGOL is a registered trademark of RIGOL Technologies, Inc.
Publication Number
QGA13101-1110
Notices
RIGOL products are protected by patent law in and outside of P.R.C.
RIGOL reserves the right to modify or change parts of or all the specifications
and pricing policies at company’s sole decision.
Information in this publication replaces all previously corresponding materials.
RIGOL shall not be liable for losses caused by either incidental or consequential
in connection with the furnishing, use or performance of this manual as well as
any information contained.
Any part of this document is forbidden to be copied or photocopied or
rearranged without prior written approval of RIGOL.
Product Certification
RIGOL guarantees this product conforms to the national and industrial standards in
China. International standard conformance certification is in progress.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
II
Safety Requirement
General Safety Summary
Please review the following safety precautions carefully before putting the
instrument into operation so as to avoid any personal injuries or damages to the
instrument and any product connected to it. To prevent potential hazards, please use
the instrument only specified by this manual.
Use Proper Power Cord.
Only the power cord designed for the instrument and authorized by local country
could be used.
Ground The Instrument.
The instrument is grounded through the Protective Earth lead of the power cord. To
avoid electric shock, it is essential to connect the earth terminal of power cord to the
Protective Earth terminal before any inputs or outputs.
Connect the Probe Correctly.
Do not connect the ground lead to high voltage since it has the isobaric electric
potential as ground.
Observe All Terminal Ratings.
To avoid fire or shock hazard, observe all ratings and markers on the instrument and
check your manual for more information about ratings before connecting.
Use Proper Overvoltage Protection.
Make sure that no overvoltage (such as that caused by a thunderstorm) can reach
the product, or else the operator might expose to danger of electrical shock.
Do Not Operate Without Covers.
Do not operate the instrument with covers or panels removed.
Use Proper Fuse.
Please use the specified fuses.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
III
Avoid Circuit or Wire Exposure.
Do not touch exposed junctions and components when the unit is powered.
Do Not Operate With Suspected Failures.
If you suspect damage occurs to the instrument, have it inspected by qualified
service personnel before further operations. Any maintenance, adjustment or
replacement especially to circuits or accessories must be performed by RIGOL
authorized personnel.
Keep Well Ventilation.
Inadequate ventilation may cause increasing of temperature or damages to the
device. So please keep well ventilated and inspect the intake and fan regularly.
Do Not Operate in Wet Conditions.
In order to avoid short circuiting to the interior of the device or electric shock, please
do not operate in a humid environment.
Do Not Operate in an Explosive Atmosphere.
In order to avoid damages to the device or personal injuries, it is important to
operate the device away from an explosive atmosphere.
Keep Product Surfaces Clean and Dry.
To avoid the influence of dust and/or moisture in air, please keep the surface of
device clean and dry.
Electrostatic Prevention.
Operate in an electrostatic discharge protective area environment to avoid damages
induced by static discharges. Always ground both the internal and external
conductors of the cable to release static before connecting.
Handling Safety
Please handle with care during transportation to avoid damages to buttons, knob
interfaces and other parts on the panels.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
IV
Safety Terms and Symbols
Terms in this Manual. The following terms may appear in this manual:
WARNING
Warning statements indicate the conditions or practices that could result in
injuries or loss of life.
CAUTION
Caution statements indicate the conditions or practices that could result in
damage to this product or loss of data.
Terms on the Product. The following terms may appear on the product:
DANGER
indicates an injury or hazard may immediately happen.
WARNING
indicates an injury or hazard may be accessible potentially.
CAUTION
indicates a potential damage to the instrument or other property might
occur.
Symbols on the Product. The following symbols may appear on the product:
Hazardous
Voltage
Please Refer to
Manuals
Protective
Earth
Terminal
Chassis
Ground
Test
Ground
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
V
Measurement Category
Measurement Category
DS2000 series digital oscilloscopes can make measurements in Measurement
Category I.
WARNING
This oscilloscope can only be used for measurements within its specified
measurement categories.
Measurement Category Definitions
Measurement category I is for measurements performed on circuits not directly
connected to MAINS. Examples are measurements on circuits not derived from
MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,
transient stresses are variable; for that reason, the transient withstand capability of
the equipment is made known to the user.
Measurement category II is for measurements performed on circuits directly
connected to the low voltage installation. Examples are measurements on household
appliances, portable tools and similar equipment.
Measurement category III is for measurements performed in the building installation.
Examples are measurements on distribution boards, circuit-breakers, wiring,
including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed
installation, and equipment for industrial use and some other equipment, for
example. Stationary motors with permanent connection to the fixed installation.
Measurement category IV is for measurements performed at the source of the
low-voltage installation. Examples are electricity meters and measurements on
primary overcurrent protection devices and ripple control units.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
VI
Ventilation Requirement
This oscilloscope uses fan to force cooling. Please make sure that the air intake and
exhaust areas are free from obstructions and have free air. When using the
oscilloscope in a bench-top or rack setting, provide at least 10 cm clearance beside,
above and behind the instrument for adequate ventilation.
WARNING
Inadequate ventilation may cause temperature increase which would
damage the instrument. So please keep the instrument well ventilated
during operation and inspect the intake and fan regularly.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
VII
Working Environment
Temperature
Operating: 0℃to +50℃
Non-operating: -20℃to +70℃
Humidity
Under +35℃: ≤90％relative humidity
+35℃to +40℃: ≤60％relative humidity
WARNING
To avoid short circuit inside the instrument or electric shock, please do not
operate in humid environment.
Altitude
Operating: less than 3 km
Non-operating: less than 15 km
Installation (overvoltage) Category
This product is powered by MAINS conforming to installation (overvoltage) category
II.
WARNING
Make sure that no overvoltage (such as that caused by thunderbolt) can
reach the product, or else the operator might expose to danger of electric
shock.
Installation (overvoltage) Category Definitions
Installation (overvoltage) category I refers to signal level which is applicable to
equipment measurement terminals connected to the source circuit. In these
terminals, precautions are done to limit the transient voltage to the corresponding
low level.
Installation (overvoltage) category II refers to the local power distribution level
which is applicable to equipment connected to the AC line (AC power).
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
VIII
Pollution Degree
Degree 2
Pollution Degree Definitions
Pollution degree 1: No pollution or only dry, non-conductive pollution occurs. The
pollution has no influence. For example: a clean room or air-conditioned office
environment.
Pollution degree 2: Normally only dry, non-conductive pollution occurs. Occasionally
a temporary conductivity caused by condensation may occur. For example: general
indoor environment.
Pollution degree 3: Conductive pollution occurs, or dry, non-conductive pollution
occurs which becomes conductive due to condensation which is expected. For
example: Sheltered outdoor environment.
Pollution degree 4: Pollution that generates persistent conductivity through
conductive dust, rain, or snow. For example: outdoor locations.
Safety Class
Class 1 –Grounded Product
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
IX
General Care and Cleaning
General Care:
Do not store or leave the instrument in where the instrument will be exposed to
direct sunlight for long periods of time.
Cleaning:
Clean the instrument regularly according to its operating conditions. To clean the
exterior surface, perform the following steps:
1. Disconnect the instrument from all power sources.
2. Clean the loose dust on the outside of the instrument with a lint- free cloth (with
a mild detergent or water). When cleaning the LCD, take care to avoid scarifying
it.
CAUTION
To avoid damages to the instrument, do not expose them to liquids which
have causticity.
WARNING
To avoid injury resulting from short circuit, make sure the instrument is
completely dry before reconnecting to a power source.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
X
Environmental Considerations
The following symbol indicates that this product complies with the applicable
European Union requirements according to Directives 2002/96/EC on waste electrical
and electronic equipment (WEEE) and batteries.
Product End-of-Life Handling
The equipment may contain substances that could be harmful to the environment or
human health. In order to avoid release of such substances into the environment and
harm to human health, we encourage you to recycle this product in an appropriate
system that will ensure that most of the materials are reused or recycled
appropriately. Please contact your local authorities for disposal or recycling
information.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
XI
Contents
Guaranty and Declaration .......................................................................... I
Safety Requirement ................................................................................. II
General Safety Summary............................................................................ II
Safety Terms and Symbols .........................................................................IV
Measurement Category...............................................................................V
Ventilation Requirement.............................................................................VI
Working Environment .............................................................................. VII
General Care and Cleaning .........................................................................IX
Environmental Considerations......................................................................X
Quick Start .................................................................................................1
General Inspection ..................................................................................... 1
Appearance and Dimensions ....................................................................... 2
To Prepare for Operation............................................................................. 3
To Adjust the Supporting Legs .............................................................. 3
To Connect to AC Power Supply ............................................................ 4
Power-on Inspection ............................................................................ 5
To Connect the Probe........................................................................... 6
Function Inspection ............................................................................. 7
Probe Compensation ............................................................................ 9
Front Panel Overview................................................................................ 10
Rear Panel Overview................................................................................. 11
Front Panel Function Overview .................................................................. 13
VERTICAL ......................................................................................... 13
HORIZONTAL .................................................................................... 14
TRIGGER .......................................................................................... 15
CLEAR .............................................................................................. 16
RUN/STOP ........................................................................................ 16
SINGLE ............................................................................................. 16
AUTO................................................................................................ 16
Knob................................................................................................. 17
Navigation Knob ................................................................................ 17
MENU ............................................................................................... 18
Record .............................................................................................. 19
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
XII
Print ................................................................................................. 19
User Interface.......................................................................................... 20
To Use the Security Lock........................................................................... 24
To Use the Built-in Help System................................................................. 25
Troubleshooting.......................................................................................26
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
1
Quick Start
General Inspection
1. Inspect the shipping container for damage.
Keep the damaged shipping container or cushioning material until the contents
of the shipment have been checked for completeness and the instrument has
passed both electrical and mechanical tests.
The consigner or carrier shall be liable for the damage to instrument resulting
from shipment. RIGOL would not be responsible for free maintenance/rework
or replacement of the unit.
2. Inspect the instrument.
In case of any damage, or defect, or failure, notify your RIGOL sales
representative.
3. Check the Accessories
Please check the accessories according to the packing lists. If the accessories
are incomplete or damaged, please contact your RIGOL sales representative.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
2
Appearance and Dimensions
Figure 1 Front View Unit: mm
Figure 2 Side View Unit: mm
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
3
To Prepare for Operation
To Adjust the Supporting Legs
Adjust the supporting legs properly to use them as stands to tilt the oscilloscope
upwards for stable placement of the instrument as well as easier operation and
observation of the instrument.
Figure 3 To Adjust the Supporting Legs
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
4
To Connect to AC Power Supply
This oscilloscope can accept 100-240 V, 45-440 Hz AC power supply. Please use the
power cord supplied with the accessories to connect the oscilloscope to the power
source as shown in the figure below. At this point, the oscilloscope is energized and
the power key at the lower-left corner of the front panel is in breath state.
Figure 4 To Connect to AC Power Supply
CAUTION
If the fuse needs to be changed, please return the instrument back to our
factory and the RIGOL authorized operator will change it for you.
Power Socket
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
5
Power-on Inspection
When the oscilloscope is energized, press the power key at the lower-left
corner of the front panel to turn on the oscilloscope. During the start-up process, the
oscilloscope performs a series of self-test items and you can hear the sound of relay
switching. After the self-test, the welcome screen is displayed.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
6
To Connect the Probe
RIGOL provides passive probes for the DS2000 series oscilloscopes. For detailed
technical information of the probes, please refer to corresponding Probe User’s Guide.
The following are the probes recommended for use with this oscilloscope.
Model
Description
RP3300A
300 MHz, passive probe, standard
RP3500A
500 MHz, passive probe, optional
Connect the Probe:
1. Connect the BNC terminal of the probe to a channel BNC connector of the
oscilloscope at the front panel.
2. Connect the probe tip to the circuit point under test and connect the ground
alligator clip of the probe to the circuit ground terminal.
Figure 5 To Connect the Probe
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

RIGOL
DS2000 Quick Guide
7
Function Inspection
1. Press Storage Default to restore the oscilloscope to its default
configuration.
2. Connect the earth alligator clip of the probe to the “Ground Terminal” under the
probe compensation signal output terminal.
3. Use the probe to connect the input terminal of CH1 of the oscilloscope and the
“Compensation Signal Output Terminal” of the probe.
Figure 6 To Use the Compensation Signal
4. Press AUTO.
5. Observe the waveform on the display. In normal condition, the display should be
a square waveform as shown in the figure below:
Figure 7 Square Waveform
6. Use the same method to test the other channels. If the square waveforms
actually shown do not match that in the figure above, please perform “Probe
Compensation”.
WARNING
To avoid electric shock during the use of probe, please make sure that
the insulated wire of the probe is in good condition and do not touch
the metallic part of the probe when the probe is connected to high
voltage source.
Compensation Signal Output Terminal
Ground Terminal
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]