ring Pro 2 User manual

User Guide
Access Controller Pro 2

21
Included installation hardware.
• (1) Ring Access Controller Pro 2
• (1) 8-pin, 3.5 mm Pitch Terminal Block Connector
• (1) Puck Antenna
• (4) Cable Labels
• (2) Adhesive Strips
• (1) USB Adapter
You’ll also need…
• Wires (18-22 AWG)/Cables for Connector Terminals
• Precision Flathead Screwdriver
• Wire Strippers
• Optional: RJ45 Ethernet Cable (≤ 3 meters)
• Optional: PVC Junction Box (if installed outside
of the call box or existing junction box)

43
Download the Ring app.
The Ring app walks you through setting up and
managing your Ring Access Controller Pro 2.
Search for “Ring” in one of the app stores below,
or visit ring.com/app
In the Ring app, select Set Up a Device and follow
the in-app instructions.
Connect the wires to the terminal block.
Using a precision flathead screwdriver, loosen the
terminal block connector screws. Strip about 0.25"
of the insulation to expose the wire (18-22 AWG),
then place the wire in the desired opening.
Tighten the screw to hold the wire in place. Give it a
gentle tug to make sure it’s secure. Repeat for the
rest of your wires.
Note: the positive and negative terminals
are interchangeable.

65
Remove the knockout.
If you’re using an Ethernet cable, you can skip ahead to
“Place your Access Controller.”
On your call box or junction box, identify a knockout
that is at least 1/2" away from the wall, making sure
the antenna wire can reach your Access Controller
install location.
Once you’ve found a good spot, remove the knockout.
Once you’re done, connect the wires to your desired
access control terminals. Use the included cable labels
to properly identify the wires.

87
Install the puck antenna.
Unscrew the nut and remove the washer from the puck
antenna. Insert the cable through the knockout hole,
ensuring the puck antenna is outside the call box or
junction box.
Place the washer on the antenna mounting post
and screw the nut to fix the puck antenna in place.
Make sure it’s secure, but do not overtighten.
Call or Junction Box

109
Place your Access Controller.
Remove the liner from one side of the adhesive strips
and place the strips in the recesses on the back of your
access controller. Clean the surface where the access
controller will be placed. Peel the liner o of the other
side and place the Access Controller against the clean
and dry mounting surface for 30 seconds.
If you’re mounting outside your call box, drill a hole for
the antenna and terminal block wires. Pass the wires and
terminal block through the hole.
Connect the terminal block to your
Access Controller.
Plug the terminal block connector into the mating
connector on your Access Controller.

1211
Connect the antenna or Ethernet cable.
Attach the puck antenna connector to the antenna port
on your Access Controller until it locks into place.
If you have an Ethernet connection in your call box or
junction box, plug the cable into the Ethernet port on
your Access Controller instead.
OR

1413
Power it up.
If you mounted your device outside the call box, plug it
into an outlet using the included micro USB cable and
DC power brick.
If you mounted your device inside the call box, connect
the power wires from your box to terminals 7 and 8
on the terminal block (it doesn’t matter which wire
connects to which terminal).

1615
LED and Connector Terminal Indicators.
PWR: Solid light indicates the device is powered
CELL: • Red indicates no cellular coverage
• Yellow indicates low cellular coverage
• Green indicates good cellular coverage
• White indicates the device is using Ethernet
• Blue indicates attempting to get cellular strength
LED and Connector Terminal Indicators (cont).
CON: Flashing light indicates device has
Internet connectivity
RUN: Flashing light indicates device is running
as programmed
REC: Solid light indicates device is in record mode
and scanning for access credential (only occurs
while provisioning a fob credential)
DR1 and DR2: Solid light for 2 seconds indicates
respective door is opening at that time

IMPORTANT PRODUCT INFORMATION
This device should only be installed by a professional installer or licensed electrician.
SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS
COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
Users are required to use a power supply that complies with PS2 or L.P.S. certification and
approval. Use only accessories supplied with your device, or specifically marketed for use
with your device, to power your device. Use of third-party accessories may impact your
device’s performance. In limited circumstances, use of third-party accessories may void
your device’s limited warranty. In addition, use of incompatible third party accessories may
cause damage to your device or the third-party accessory. Read all safety instructions for any
accessories before using with your device.
Protect the device from direct sunlight. Install the device at dry locations and protect it
against rain and humidity. The device may not get contact to salt water or other conductive
liquids. The device must be charged only within a building in a dry state.
SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS
COULD RESULT IN INJURY.
Small parts contained in the Access Controller Pro 2 may present a choking hazard to small
children. Keep small parts away from children. Your Ring Access Controller Pro 2 should only
be used in accordance with the instructions and intended purpose. Using this accessory in
any way other than its intended purpose could cause injury to yourself, others or damage
to the device. Your Ring Ring Access Controller Pro 2 is not waterproof and as such should
not be submerged in water, doing so could cause injury to yourself, others or damage to
the device.
DANGER — TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, FOLLOW THESE
INSTRUCTIONS CAREFULLY.
• Do not force the adapter into a power outlet.
• Do not expose your device or adapter to liquids. If your device or adapter gets wet,
carefully unplug all cables without getting your hands wet and wait for the device and
adapter to dry completely before plugging them in again. Do not attempt to dry your
device or adapter with an external heat source, such as a microwave oven or a hair dryer.
If the device or adapter appear damaged, discontinue use immediately. Use only acces-
sories supplied with the device to power your device. To avoid risk of electric shock, do
not touch your device or any wires connected to your device during a lightning storm.
• If the adapter or cable appears damaged, discontinue use immediately.
Install your power adapter into an easily accessible socket-outlet located near the equipment
that will be plugged into or powered by the adapter.
Product Specifications
Model No.: ecBAC-1
Temperature Rating: -20°C to 65°C
Power Input: 100–240V ~0.3A 50/60Hz
Power Output: 5.2V, 1.8A (9 watts)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose
of, or recycle, your device in accordance with your local laws and regulations. For infor-
mation about recycling your device, go to amazon.com/devicesupport.
TERMS OF SERVICE AND WARRANTY
By purchasing or using the product, you agree to the Terms of Service found at
ring.com/terms.
For information on our warranty, visit ring.com/legal.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the
user that are not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines. Information on the product
is on file with the FCC and can be found by inputting such Product’s FCC ID (which can be
found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid.
The party responsible for FCC compliance is: Ring LLC, 1523 26th St, Santa Monica, CA USA,
90404
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled envi-
ronment and it also complies with Part 15 of the FCC RF Rules. This equipment must be
installed and operated in accordance with provided instructions and the antenna(s) used for
this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna installation instructions
and consider removing the no-collocation statement.

For information on our warranty, visit ring.com/legal
© 2021 Ring LLC or its aliates. Ring and all related marks
are trademarks of Ring LLC or its aliates.
Additional info
Manufactured by: Ring LLC
Website: Ring.com
Contact Name: RACP Tech Support
Contact Number: 1-888-255-1041
Email: [email protected]

XX-XXXXXX-XX