Soyal AR-331-E User manual

V200422
AR-331-E/EF
SOYAL
ACCESS CONTROL SYSTEM
8
89
CN1 CN2
CN4 CN5 CN6 RJ45
AR-331-E AR-331-EF
12
34
56
78
90
最佳感應區
CN1CN4
CN2 CN6
CN11
CN9
CN3
CN5
Contents
1Product
Security Torx Wrenches
Security Torx: M3x10
Flat Head Cap Philips
Tapping Screw: 4x20
Wire Application Wire Color Description
Lock Relay 1Blue White (N.O.)DC24V1Amp
2
Purple White (N.C.)DC24V1Amp
Common-COM-Point
3White (COM)DC24V1Amp
Door Contact 4Orange Negative Trigger Input
Exit Switch 5Purple Negative Trigger Input
Alarm Relay 6Gray Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Power 7Thick Red DC 12V
8Thick Black DC 0V
CN1Cable:
Wire Application Wire Color Description
Anti-Tamper
Switch
1Red N.C.
2Orange COM
3Yellow N.O.
CN5Cable:
Wire Application Wire Color Description
Power 1 Red DC 12V Output
Security trigger signal 2Purple Security trigger signal Output
Arming 3 Red White Arming Output
Duress 4 Yellow White Duress Output
CN6Cable:
Wire Application Wire Color Description
1 --- ---
2 --- ---
TCP/IP Output
3
Orange White
Net - TX+
4Orange Net - TX-
5Green White Net - RX+
6Gerrn Net - RX-
7 --- ---
CN3Cable:
Wire Application Wire Color Description
TTL Output
1 Blue CLK
2 Red DC 5V
3
Orange
RX
4White TE
5Yellow TX
6Black DC 0V
CN9Cable:
Wire Application Wire Color Description
RS-485 for Lift
Controller
1Thick Green RS-485(B-)
2Thick Blue RS-485(A+)
CN4Cable:
Wire Application Wire Color Description
Beeper 2Pink Beeper Output 5V/100mA, Low
LED 3Yellow Red LED Output 5V/20mA, Max
4Brown Green LED Output 5V/20mA, Max
Door Output 5Blue White Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Wiegand 6Thin Green Wiegand DAT: 0 Input
7Thin Blue Wiegand DAT: 1 Input
WG Door Contact
8Orange Negative Trigger Input
WG Exit Switch 9Purple Negative Trigger Input
CN2Cable:
Installation
Connector Table
Peel o󰀨 screw hole rubbers and frame rubber from rubber pad
Put screw rubbers on the back side of the mounting plate and pull the
cables from the square hole of the mounting plate.
Put a frame rubber on the frame groove of body
Connect the terminal cables to the body and attach the body to the
mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power and LED will light and beep will sound.
4Accessories 2Terminal Cables 3Tools
Front Panel & Indicator
While power on the device,
hands off the touch panel
for 10 sec. to make sure
a successful activation.
Peel
off
screw
rubber
Peel
off frame
rubber
4
5
1
4
2
3
5
6
7
Screws
Rubber
Frame
Rubber
Put on/Take off together
5Option
1White
DI1 Reserved
Arming / Blue LED
Input (Active High)
Yellow LED Input
(Active High)
Left LED Descrption Descrption
Yellow
Blue Power-on/Stand-by
/OK
Error/Alarm
Right LED
Green
Red
Rubber Pad
TCP/IP
Module

V200422
AR-321H
N.C.
N.O.
CTL
12V
Door Contact
ALM
12V
GND
12V
GND
12V
GND
12V
GND
N.C.
CN1
331-E/EF WGoutput 331-E/EF Master
EXIT
E
12V
GND
Exit Switch
12V
GND
12V
GND
N.O.
GND
N.O.
COM
PB
12V
GND
3
4
5
6
7
8
2
1
CN1
CN1
N.O.
COM
PB
12V
GND
3
2
1
EXIT
12V
GND
12V
GND
12V
GND
N.O.
GND
4
5
6
7
8
1
2
3
4
5
6
7
8
COM
EXIT
N.C.
N.O.
COM
CTL
12V
GND
PB
12V
GND
12V
GND
N.O.
12V
GND
12V
GND
DDR
PB
CN1
CN6
12V
1
2
3
4
5
6
7
8
4
1 2 3
N.C.
N.O.
COM
CTL
12V
E
12V
GND
Exit Switch
12V
GND
CN2
CN1
BZ
RLED
GLED
Door Output
WG 0
WG 1
WG-DS
WG-PB
N.C.
EXIT
1
2
3
4
5
6
7
8
1
2
3
5
6
7
8
4
BZ
RLED
GLED
WG 0
WG 1
12V
GND
12V
GND
CN1 CN1
CN6
CN2 CN2
BZ
RLED
GLED
Door Output
WG 0
WG 1
DS
PB
DS
PB
Duress
ALM
COM PB 12V GND 12V GND
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
2
3
4
5
6
7
8
1
2
3
4
1
2
3
4
5
6
7
8
9
99
11
EXIT
N.C.
COM
PB
12V
GND
N.O.
N.O.
COM
N.C.
V+
V-
Fingerprint
Biometrics Device Access controller
Connect to Electric Bolt Connect to Magnet Lock
Wiring Diagram
Electric Bolt
Controller
Controller
Controller
Controller
Reader
Controller
Controller
RTE
RTE
RTE
RTE
RTE
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
Magnet Lock
Connect to Electric Strike
Electric Strike
Alarm
Relay Output Module
Door Contact
Door Contact
Connect to Door Contact
Strengthen security with Digital Relay Board
Electric Bolt
Connect to Reader
AR-331-E/EF become WG mode
(28 000 )
1. When AR-331-E/EF become WG mode,it can be used with any
controllers.
2. AR-331-E/EFsupport Anti-pass-back by nger or card.
※Using Rule :
Finger : Both AR-331-EF Master mode and AR-331-EF WG mode
must store all the same FP data and real or visual card number.
Card : Can pass WG message to controller.
POWER
12VDC
Digital Relay Board

V200422
AR-331-E/EF
SOYAL
ACCESS CONTROL SYSTEM
Adding and Deleting Tag
Delete All Tags
Input 123456 (or Master Code) → 29 29
Delete a Single Tag
Input 123456 (or Master Code) → 10 SSSSS EEEEE
[e.g.] Delete User Address: 00058
Access programming mode → 10 00058 00058
9
9
Delete a batch of Tags
Input 123456 (or Master Code) → 10 SSSSS EEEEE
[e.g.] Delete User Address: 00101~00245
Access programming mode → 10 00101 00245
9
9
Add Single Tag or Random tags
Input 123456 (or Master Code) → 19 UUUUU 00001 → Present the tag(s) with Controller (single tag or random numbered cards one by one) → Done
[e.g.] 2 readom cards with user addresses No. 100 and No. 101:
Access programming mode → 19 00100 00001 → Present the tags one by one → Done
Input 123456 (or Master Code) → 19 UUUUU QQQQQ → Present the tags (Present the tag with the lowest number rst.) → OK
Add the Sequential tags
[e.g.] User Address NO.101 to NO.120 have 20 pcs of sequential tags:(62312~62332)
：
Access programming mode → 19 00101 00120 → Close Tag into RF Area(only use the tag NO.62312) → OK
Tag Information
SITE CODE
CARD CODE
SITE CODE
CARD CODE
Changing the Master Code
Access programming mode → 09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] If want to changing the Master Code= 876112, input 123456 → 09 876112876112
Exiting
Input
Access programming mode → 00 NNN MMM AAA
[NNN= Node ID: 000~254; MMM=AR-331-E/EFDoor NO.:1~255; AAA=WG Reader Door NO.:1~255
B. Changing the Node ID of Reader
Programming
A. Entering and Exiting Programming Mode
Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input 876112 → Access programming mode
Enable device
Access programming mode → 20 U DDD U= Enable target unit(0=AR-331-E/EF,1=Reader) [Please refer to function default value for details.]
[e.g.] If the AR-331-E/EFset to exit reader, WG Reader set to access reader.
Access programming mode → 20 0 128 → 20 1 192 [Please refer to function default value for details.]
Enable/Disable auto open zone
Access programming mode → 20 U DDD U= Enable target unit(0=AR-331-E/EF,1=Reader) [Please refer to function default value for details.]
[e.g.] If the AR-AR-331-E/EFset to Enable aut open zone.
Access programming mode → 20 0 004 [Please refer to function default value for details.]
[e.g.] If the WG Reader set to Enable aut open door without presenting card.
Access programming mode → 24 1 128 [Please refer to function default value for details.]
Enable/Disable auto open door without presenting card
Access programming mode → 24 U DDD U= Enable target unit(0=AR-331-E/EF,1=Reader) [Please refer to function default value for details.]
[e.g.] User address from 00152 to 00684 enable the anti-pass-back function: 26 00152 00684 0
Enable card user
Access programming mode → 26 SSSSS EEEEE P SSSSS= starting user address; EEEEE= ending user address [P=0 Enable/ P=1 Disable/ P=2 Reset]
[e.g.] AR-331-E/EF(without WG reader), to set second time zone which could be passed only at 9:30am to 4:20pm on Mon, Wed and Fri.
Access programming mode → 08 10 02 09301620 01010100 → setting is completed
Setting up access time
Access programming mode → 08 MW NN HHMMhhmm 7123456H [M=AR-331-E/EF; W=Reader(0=disable,1=enable); NN: 16 sets of
auto-open zone (NN=00~15); HHMMhhmm=Starting time to ending time; 7123456H= 7 days of week + Holiday (F= 0: disable; 1: enable)]
Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or somewhere wants to
monitor not only the access but also exit condition.
Door will keep opening after rst man ashing card. When the reader is stand-alone, supporting only 16 sets of auto-open zone by device setting.
Auto-open zone can extend up to unlimited sets by Networking.
C. Anti-pass-back
D. Auto Open Zone

V200422
Fingerprint
Biometrics Device Access controller
E. Lift control
Single oor
[e.g.] User address NO. 45 only can reach the elevator to the 24th oor: 27 00045 24
Access programming mode → 27 UUUUU LL
UUUU=User Address LL=Floor number (01~64 oor)
Connect with AR-401RO16B to control oors which the user will be able to access. [BAUD9600]
Set
(G)
Floor
L
8
16
24
32
40
48
56
64
0
1
2
3
4
5
6
7
L
6
14
22
30
38
46
54
62
L
7
15
23
31
39
47
55
63
L
5
13
21
29
37
45
53
61
L
4
12
20
28
36
44
52
60
L
3
11
19
27
35
43
51
59
L
2
10
18
26
34
42
50
58
L
1
9
17
25
33
41
49
57
Please refer to below oor chart
[e.g.] User address NO. 168 can reach only the 6th and 20th oor:
Access programming mode → 21 00168 0 00100000
→ 21 00168 2 00001000 → OK (Please refer to oor chart as right.)
Multi oors
Access programming mode → 21 UUUUU G LLLLLLLL
[UUUUU=User address G: 8 sets of lift control (Input: 0~7) LLLLLLLL:
8 oors setting (L=0=Disable, L=1=Enable)
Enable all devices: Access programming mode → Enable particular device: Access programming mode → U
Enable Arming status:
Disable Arming status:
Standby Mode
Standby Mode
Enter Program Mode
Card only
Card only
Card or Passcode
Card or Passcode
Card and Passcode
Card and Passcode
※ Factory default armingcode is: 1234. U=Reader unit (0=AR-331-E/EF, 1=WG Reader).
F. Setting Up the Arming
Conditions:
1. Arming is enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: Arming is enabled and the power is suddenly o󰀨 then on.
Enable all devices
Induct valid card → Input 4 digit
arming code →
Enable particular device
Induct valid card →Input 4 digit
arming code →U or
Disable particular device
Induct valid card →Input 4 digit
arming code →U or
Input 5 digit user address → Input 4
digit pass code → → Input 4 digits
arming code → or U
Induct valid card →Input 4 digit pass
code →→Input 4 digits arming
code →or U
Disable all devices
Induct valid card → Input 4 digit
arming code → 9
Input 5 digit user address → Input 4
digit pass code → → Input 4 digits
arming code → or U
9
Induct valid card →Input 4 digit pass
code →→Input 4 digits arming
code →or U
9
G. Adding / Deleting Fingerprint
H. Enable/Disable Skip Finger/Tag
Adding
How to add a nger data:
Access programming mode → Place your nger on the sensor
[F=1= Adding 1 Finger data; F=2= Adding 2 Finger data; UUUUU= User address]
FUUUUU
93
Deleting
UUUUU= User address
Access programming mode → 0UUUUU
93
Deleting All
Access programming mode → 999999
93
※If you hear continuous "beep..." sounds when you place nger on the sensor, please release your nger from the sensor.
(Please consult detail command on page 8.)
Command Setting Software Setting Access Mode Way
40 1 NNNNN EEEEE
40 3 NNNNN EEEEE Just ngerprint
Just card control
FP rst and then Tag First Then
40 0 NNNNN EEEEE
40 2 NNNNN EEEEE Just ngerprint
Just card control
FP only or Tag only
Access programming mode →
NNNNN＝starting user address
EEEEE= ending user address
F＝1+3(Default Value)
FNNNNN EEEEE
04
or
I. Adding / Deleting Fingerprint
1. For dual-ngerprint sensor module version, capactive sensor module is the only enabled way for enrolling FP.
2. For dual-ngerprint sensor module version, user just can select one of ngerprint sensor for identication and can't put two ngerprints to di󰀨erent sensor at the same time.
3. Extra WG keypad panel is needed for adding card or downloading data connected to PC.
4. Each nger need to be collected 1 times enrolling for AR-331-E/EF.
J. The process of FP identication
1. While attached a nger on biometric sensor, there is a beep sound for starting the scanner. Then, please don't move your nger until the AR-331-EF makes
another beep sound.
2. If there is a 8-beep sound after user gets access by FP, the FP data shall be reset by command 39*9*99999# under the programming mode.
Cautions: Before reset the FP, please backup the data from source FP rst.
Adding
1 Fingerprint
(By DO)
Finger
1Bi Di Bi Long Bi
(OK)
Adding
2 Fingerprint
(By DO)
Finger
1Bi Di Bi Long
Bi
(OK)
Finger
2
Long Bi
(OK)
Di Bi
Di Bi Bi Di Bi Di Bi
Adding
3 Fingerprint
(By DO)
Finger
1Bi Di Bi Long
Bi
(OK)
Finger
2
Long Bi
(OK)
Di Bi Bi Di Bi Di Bi Finger
3
Repeat
Finger 2

V200422
AR-331-E/EF
SOYAL
ACCESS CONTROL SYSTEM
3
4
5
7
8
1
2
6
Restoring Factory Settings
Reset all device parameters and user card data
Use the Button on the PCB:
Use the command:
Press “IP Reset Button” of main board for few
seconds,then IP and all device parameters will reset.
(Reference to picture)
Reset all device parameters and user card data:
Access programming mode → 29 299
Firmware Upgrade
Get the upgrade software from SOYAL or our distributor and run “UdpUpdater” software
Update the rmware
[Please login the SOYAL web to download the new ISP Firmware.]
1. Input the Target Address and Port
2. [Load F/W] open the documents that have the new ISP Firmware
3. Click the new ISP Firmware and [Open] it
4. Click [Update Device] to start the rmware update
5. Till the screen shown [Firmware Update is Complete]
Execute the software
The software is within SOYAL CD or Login the
SOYAL web to downloads
Reset all user card data:
Deleting All Fingerprint:
Access programming mode → 29 29
Access programming mode → 39 9 99999
1
2
5
4
3
Transfer ngerprint format V9 -> V5
7. Click "SIF→FP5 " ,select old AR-331EF FP le format. SIF , the
system will automatically generate new single FP le format. FP5
into 701Server folder.FP5 into 701Server folder.
Deleting ngerprint database on the device
8. Click"Delete All" , all Fingerprint data from device will be deleted
completely.
1. Select correct "COM Port".
2. Select "Node ID" of the device. Input "User Address".
3.
Select the numberof enrolled ngers in assigned path ( 1FP or 2FP per User).
4. Select the device type " AR-331-EF ".
5. Select “Save Path” in which will save ngerprint data.
6. Click “Enroll”, follow pop-up picture and Status bar to enroll FP as below:
Connect to Controller
—》
Place 1st nger 1st time to Finger sensor
—》
remove nger
—》
Place 1st nger 2nd time
—》
remove nge
—》
Place
2nd nger 1st time
—》
remove nger
—》
Place 2nd nger 1st time
—》
Save FP data to File
—》
Registration Completed.

V200422
Fingerprint
Biometrics Device Access controller
IP Setting
Log-in User Password
When you choose the "Networking Setting" or "User Password" at rst.
Log-in window will pop out and please input
※ At the Factory Default
User name: SuperAdm
Password: 721568
Open your Web Browser and input factory default IP
address: ht tp://192.168.1.127
Networking Setting
You will nd initial IP Address 192.168.1.127 and check
MAC Address is the same as sticker on Ethernet Module
device. Please revise IP address you want, and then click
“Update” button. After updating the IP, please re-connect
the Web Browser by new IP address.
User Password
The password composes of 10 characters at most, it can be
either A~Z or 0~9.
Change the log-in password to lock the IP setting of
Ethernet Module.
If the IP address of AR-331-E/EF has
changed We must enter the new IP
address.
Current IP address of the AR-331-E/EF
Page menu
Current State
Online Status is able to monitor and show which computer is linking on
Ethernet Module
IP Setting
Monitor the on-line computer
Change the Log-in information
Command List (By WG Keyboard)
Function Command Exposition
Entering programming mode PPPPPP PPPPPP: Master Code, (Default value: 123456)
Exiting programming mode
Exiting programming mode and enabling all device
into arming status. Including AR-331-EF, WG Reader
Enabling each device into arming status. U U＝Enable target unit (0=AR-331-EF , 1=WG Reader)
Node ID setting 00 NNN MMM AAA
NNN＝Node ID,(001~254)
MMM＝AR-331-EF Door Number,(001~255)
AAA＝WG Reader Door Number,(001~255)
IP Address assign (Must power reset)
01 0 CCCCCCCCCCCC
default value = 192.168.1.127
CCCCCCCCCCCC = 192168001127
If set to 000.000.000.000 will enable DHCP otherwise
will disable DHCP
01 1 255255255000 Netmask
01 2 192168001254 Gateway assign

V200422
AR-331-E/EF
SOYAL
ACCESS CONTROL SYSTEM
Command List (By WG Keyboard)
Function Command Exposition
Door relay time setting 02 U TTT
U＝Enable target unit (0=AR-331-EF , 1=WG Reader)
TTT＝Door relay time
000 (Output constantly)
001~600＝1-600 Sec.；601~609＝0.1~0.9Sec.
Alarm relay time setting 03 TTT TTT
＝Alarm relay time；000 (Output constantly)
001~600＝1~600 Sec.
Arming delay time setting 05 TTT Base on second, range: 001~255
Alarm delay time setting 06 TTT Base on second, range: 001~255
Master card setting 07 SSSSS EEEEE SSSSS-EEEEE＝00000~15999
SSSSS= starting user address; EEEEE= ending user address
Auto-open zone setting 08 MW NN HHMMhhmm
7123456H
M=AR-331-EF; W=WG Reader (0=disable; 1=enable)
NN＝16 sets of auto-open zone (Range: 00~15)
HHMMhhmm=staring time to ending time
(e.g.: 08301200=08:30 to 12:00)
7123456: 7 days of week -Sun/Mon/Tue/Wed/Thu/Fri/Sat
(Input value: 0=disable; 1=enable)
H: Holiday (Input value: 0=disable; 1=enable)
Master code settings 09 PPPPPPRRRRRR PPPPPP= New master code
RRRRRR= Repeat the new master code
Suspend or delete tags Suspend：10 SSSSS EEEEE :Suspend :Delete
SSSSS= starting user address; EEEEE= ending user address
Delete： 10 SSSSS EEEEE
Recover tag 11 SSSSS EEEEE SSSSS= starting user address; EEEEE= ending user address
Setting up Card or PIN mode by user address 12 UUUUU PPPP~PPPPPPPP
UUUUU= user address;
PPPP~PPPPPPPP=4digit (default)~8-digit individual PWD
(Access mode: Card or PIN)
Arming output setting 14 TTT Base on 1ms, range:1~255, default value=10,
Input 0= Timeless
Duress code setting 15 PPPP PPPP＝4-digit PWD (0001-9999) Default value：4321
Arming PWD setting 17 PPPP PPPP＝4-digit PWD (0001-9999) Default value：1234
Enabling or Disabling into arming status Card+NNNN NNNN
：Arming PWD
U＝Enable target unit (0=AR-331-E/EF, 1=WG Reader)
Enabling or Disabling each device into arming status. Card+NNNN U
Enabling all device into arming status. Card+NNNN
Disabling all device into arming status. Card+NNNN
Door open waiting time 18 U TTT U＝Enable target unit (0=AR-331-EF , 1=WG Reader)
TTT=Door open waiting time:001~600;default value:15 sec.
Add card by presenting 19 UUUUU QQQQQ
Reader additional setting 20 U DDD U＝Enable target unit (0=AR-331-E/EF, 1=WG Reader)
DDD=Function default value
Lift control setting: multi-doors 21 UUUUU G LLLLLLLL UUUUU＝user address；G=4 sets of lift control(0~3);
LLLLLLLL=8 assigned oor (F=0: Disable, 1: Enable)
Add/Delete tag by presenting (M6 only) 22 N N=0(Delete tag); N=1(Add tag)
AR-401RO16/ AR-401RO16B relay time setting 23 MMM TTT MMM=Node ID of lift controller
TTT= relay time: 000~600=1~600 sec.
Factory setting 24 U DDD U＝Enable target unit (0=AR-331-E/EF, 1=WG Reader)
DDD
：Function default value
Real time clock setting 25 YYMMDDHHMMSS YYMMDDHHMMSS ＝Year/Month/Day/Hour/Min./Sec.
Anti-pass-back (Enable user) 26 SSSSS EEEEE P SSSSS= starting user address; EEEEE= ending user address
P=0=Enable; P=1=Disable; P=2=Initial
Lift control setting: single door 27 UUUUU LL UUUUU＝user address；LL：Floor number(01~64 oor)
Duress Function and Arming output setting 28 FFF Arming output and Duress function: FFF= 008 (default value)
Delete all tag/Delete all tag + parameters setting 29 29 / 29 299
Same tag reading interval time 31 TTTT Base on 10ms, range from 10 to 6000
Auto ring the clock alarm schedule 32 SS HHMMTT 7123456H
SS= 16 sets auto alarm schedule, range 0~15
HHMM= HH:MM (ex. 0830: Ring bell at 08:30)
TT=Period of time to ring bell
(Base on second, range 01~99 sec.)
7123456: 7 days of week -Sun/Mon/Tue/Wed/Thu/Fri/Sat
(Input value: 0=disable; 1=enable)
H: Holiday (Input value: 0=disable; 1=enable)
Holiday Setting 35 MMDD F
MM= Month of year (01=Jan...10=Oct.)
DD= Date of month (01=1st day of month)
F= 0:Delete ; 1: Add
9
9
9
QQQQQ=Card quantity(00001=Continuously inducting)
UUUUU＝user address

V200422
Fingerprint
Biometrics Device Access controller
Command List (By WG Keyboard)
Function Command Exposition
Enabling or Disabling into Full Access status 36 MW M=AR-331-EF ; W=WG Reader (0=disable; 1=enable)
RS485 port function setting
(Needs to be restarted after setting) 37 AB
A＝0:AR401RO B＝0: 9600(default value)
1:Host (default value) 1: 19200
2:LED Panel 2: 38400
3:Printer 3: 57600
Adding / Deleting Fingerprint 39 F UUUUU F＝1: Adding one nger data / 2: Adding two nger data
3:Adding three nger data / 0: Delete
UUUUU＝user address
Deleting All Fingerprint 39 9 99999
En/Disable Skip Finger/Tag 40 F NNNNN EEEEE
First 40*1*NNNNN*EEEEE#
Then 40*3*NNNNN*EEEEE#
Change WG bits output format 41 n n：0＝WG26 ；n：1＝WG34
PIN & UID Length setting 42 m n m＝PIN code Length 4~8 Digit
n＝UID Length 4~8 Digitn＝UID Length 2~8 Digit
Function Default Value
20 U DDD ※Default Value
Function Option Value Bit Application
Entry and Exit Access is recorded on Duty Report ※0: Yes 1: No 001 0Networking
Activate close door automatically lock (Auto-Relock) ※0: Disable 1: Enable 002 1Networking/Stand-Alone
Auto Open ※0: Disable 1: Enable 004 2Networking/Stand-Alone
When Access Mode is "Card and PIN", Readers can skip pressing PIN code ※0: Disable 1: Enable 008 3Networking/Stand-Alone
Exit by Push Button 0: Disable ※1: Enable 016 4Networking/Stand-Alone
Enable force Open trigger alarm ※0: Disable 1: Enable 032 5Networking
Entry/Exit Reader ※0: Exit 1: Entry 064 6Networking
Anti-pass-back ※0: Disable 1: Enable 128 7Networking
Access mode: FP rst and then Tag (Default Value)
setting a pair of command
setting a pair of command
Access mode: FP only or Tag only
First 40*0*NNNNN*EEEEE#
Then 40*2*NNNNN*EEEEE#
NNNNN= starting user address;EEEEE= ending user address
24 U DDD ※Default Value
Function Option Value Bit Application
Enable Egress Beep Sounds ※0: Enable 1: Disable 001 0Networking/Stand-Alone
---- ---- ---- 002 1----
---- ---- ---- 004 2----
Arm/Disarm Zone(Zone: 62) ※0: Enable 1: Disable 008 3Networking/Stand-Alone
Reader and controller share the same door relay
(only for WG reader)
0: Disable ※1: Enable 016 4Networking/Stand-Alone
Free Access Mode ※0: Disable 1: Enable 032 5Networking/Stand-Alone
Stop alarm by pressing push button or closing the door ※0: Disable (must swipe valid card) 1: Enable 064 6Networking/Stand-Alone
Enter auto open time zone without presenting valid card ※0: Disable (must present valid card rst) 1: Enable 128 7 Networking/Stand-Alone
28 FFF ※Default Value
Function Option Value Bit Application
Expiry User Access Trigger Alarm ※0: Disable 1: Enable 001 0Networking/Stand-Alone
Reset Anti-Passback on Timezone 61 ※0: Disable 1: Enable 002 1Networking/Stand-Alone
--- ---- ---- 004 2----
Duress and Arming Output function 0: Wiegand Output 1: Arming and Duress Output 008 3Networking/Stand-Alone
RS-485
Lift Control: 0 000
4-5 Networking/Stand-Alone
Host: 1 016
LED Board: 1 032
Printer: 1 048
---- ---- ---- 032 6----
---- ---- ---- 064 7----
※ U=Controller/Reader
(0= Master Controller;
1= Slave Reader);
DDD= Weighted Value
Step 1: Select the ‘Function’ that you need for each command
(20*, 24*, 28*)
Step 2: ‘Option’ of function that you need, it is either 0/1 option value.
Step 3: Subtract the ‘Value’ of each Option with ‘Option’ Value.
Example 1:
Setting up Main Controller under command 20* for
function ‘Enable force Open trigger alarm’ + ‘Entry
Reader’ + ‘Anti-pass-back’ = (1*032) + (1*064) +
(1*128) = weighted value 224; enter 24*0*224#
Weighted Value Manual