Rinnai RGK-61D User manual

Infrared Gas Griller
(Lower Flame Type)
RGK-61D
RGK-62D
RGK-64
RGB-60B
For Commercial Use
Model Name
Operation Manual
Contents
Thank you for purchasing this infrared gas
griller (lower flame type).
•Before use, please read this manual
carefully for safe and proper use of this
appliance.
•This appliance is for commercial use.
Not for domestic use.
•In case of change of user, be sure to let
the new user to read this Manual and
provide instructions on the use of this
appliance.
•In case this operation manual is
missing, please contact your dealer or
Rinnai and repurchase this manual.
Dear Valued Users
RGK-61D
• Safety Precautions Be sure to observe the precautions ............1
SAFETY PRECAUTIONS ...................................................... Page
• Preparations Before Use .............................................................. 5
• Names of Each Parts ................................................................... 7
• Preparations and Verification Before Use .................................... 9
• Daily Inspection and Cleaning ....................................................11
• About consumable parts ............................................................ 12
BEFORE USING THE GRILLER
HOW TO USE
TROUBLESHOOTING
• Fault/Error Identification and Remedy ........................................13
• Dimensions ................................................................................13
• Specifications .............................................................................14
OT_Manual for RGK-61D, 62D, 64

Be sure to observe the precautions
Various symbols are used in this manual to ensure safe and proper installation of the
appliance and to prevent any injury or damage to installation personnel or property.
The indication and meaning of the symbols are as outlined below. Please have a good
understanding of these safety precautions before reading the main text of the manual.
This indicates an immediate hazard that, if ignored, could result in death,
serious injury or fire due to incorrect operation.
This indicates hazard that, if ignored, could result in death, serious injury
or fire due to incorrect operation.
This indicates hazard that, if ignored, could result in injury or damage to
property only due to incorrect operation.
The definitions for the following symbols are as follows:
• If you suspected a gas leakage, never
ignite any fire, turn on/off the switch of
any electrical appliance or use the
telephone located around the gas appliance.
Flame or spark may ignite fire and an
explosion could occur.
CAUTION
WARNING
DANGER
DANGER
Attention – This symbol denotes an item for which
care should be taken.
Caution with fire
Caution on high temperature
Forbidden – This symbol denotes a forbidden action.
No fire
Disassembly
prohibited
Do not touch
Compulsory – This symbol denotes a compulsory action.
If you detected a gas leakage, stop using
the appliance immediately.
1 Stop using the appliance and shut off
the gas valve (gas cock) immediately.
2 Open the windows and door for the gas
to escape.
3 Contact your dealer or gas supplier.
•
No fire
Compulsory
Cautions when the gas leaks
1SAFETY PRECAUTIONS
1

•Caution for the type of gas supplied
•
Ensure that the type of gas (gas group) supplied is same as the one mentioned on the nameplate of the appliance.
•
Use of the appliance with incorrect gas type could result in carbon monoxide poisoning due to incomplete
combustion or burn injury due to explosive ignition.
•
When you move to another house, ensure that the type of gas supplied is same as the one mentioned on the
nameplate once again.
•About installation
•
Be sure to observe the precautions on installation to ensure compliance with the Fire Prevention Ordinance.
Insufficient clearance around the appliance may result in fire. Even if an inflammable wall is covered with the
object such as stainless steel plate, it is necessary to maintain the same distance as required for combustible
objects.
•
Do not refurbish the appliance’s surroundings after the installation (such as enclosing the appliance,
installation of hanging shelf). Such a refurbishment may not be compatible with the installation standards or
cause imperfect combustion or fire.
•Safety distance to combustible object and fire prevention measures
•
If the distance of at least 20cm (sides), 15cm (rear)
(for RGK-62D, 20cm and above) and 100cm (top) is
unavailable between the appliance and flammable
wall, installation of a heat insulating plate is required
as shown in the illustrations on the right.
•Do not leave the griller while the burner is on
Leaving the griller or going to sleep while the burner is on is
strictly prohibited. The food being grilled could burn or catch
fire and may result in fire damage.
Heat insulating plate
Material Thickness Caution
Steel plate
Stainless steel plate
0.6cm and above
0.6cm and above
Ensure a space at least 3cm and provide adequate
reinforcement to prevent harmful deformation.
WARNING
•
I f the wall around the appliance is flammable
(such as wooden wall), be sure to keep a
distance of at least 20cm, 15cm (for RGK-62D,
20cm and above) and 100cm for sides, rear
and top respectively.
RGK-61D, 62D, RGB-60B
Gap between ceiling
and side wall
Gap between
back wall side
100cm
and above
20cm and above
0cm and above
Combustible
object
20cm and above (RGK-62D)
15cm and above
0cm and above
Combustible
object
RGK-61D, 62D, RGB-60B
Heat insulating plate
Heat insulating plate
Gap 3cm
and above
Gap 3cm and above
50cm and
above
0cm and
above
Leave a gap
0cm and above
0cm and
above
0cm and above
80cm and
above
0cm and
above
Combustible
object Combustible object
RGK-64
Gap between ceiling and side wall
Combustible object Combustible object
Combustible
object
Combustible
object
20cm and above 20cm and above
100cm and above
Combustible
object
0cm and above 0cm and above
15cm and above
0cm and above
Gap between back wall side
RGK-64
3cm and above
Combustible object Heat insulating plate
0cm and above 0cm and above
80cm and above
Combustible object Combustible object
Leave a gap
3cm and
above 0cm and
above
0cm and
above
0cm and
above
Leave a
gap
0cm and
above
3cm and
above
Heat insulating plate
Heat insulating
plate height
50cm and
above
0cm and
above
The nameplate is placed on
the right side of the griller.
<Nameplate>
Example) 96.06 (Manufactured on June 1996)
Confirm the gas type
(Model name)
(Manufactured date)
(Type of gas (gas group))
(Serial No: YS)
(Distributor)
(Gas consumption)
2

•
Do not allow children to use this product without
adult supervision. Keep out of reach of infant and
small child. Failure to
observe this warning
may result in burn or
injury.
•
If case of earthquake or fire or when any unusual
state is observed, stay calm and stop using the
appliance, and shut off the gas valve.
•Use a gas rubber hose (authorized
by local association).
Crack on the hose or loose hose
connection can cause gas poisoning
or gas explosion. Be sure to replace
damaged rubber hose with new one.
•Push the rubber hose onto the
fitting up to the red line and
secure it with a hose clamp.
•Do not connect additional
rubber hose or branch out
the hose.
•
No placing of combustible object near the
appliance
Do not place any combustible object (such as
curtain, newspaper and paper bag) or inflammable
object (such as spray can) on top of or around
the appliance. These objects
could burn or catch fire and
may result in fire damage.
WARNING
CAUTION
•
Do not use this appliance on any unstable surface
or on top of combustible object such as newspaper
and plastic sheet. Failure to observe this warning
may result in fire.
Caution with fire
•
Users other than repair personnel must never
disassemble, repair or modify this appliance.
Failure to observe this warning may result in fire,
gas leakage or injury due to malfunction.
Diassembly
prohibited
•
Do not put water on the appliance. Doing so can
cause imperfect combustion or explosion-like
ignition.
3

•
After use, make sure that the fire has been
extinguished. Be sure to shut off the gas valve
before going out or going to sleep.
CAUTION
Do not touch
•
Do not use in vehicle or ship.
The appliance may tilt while in use
and cause fire or burn injury.
•
Always ensure the ventilation (air inlet/exhaust)
of the place where this appliance is used.
Do not block the ventilation with any object.
Turn on the ventilation fan or
take other measures to
maintain good
ventilation while
in use.
•
Do not use the appliance for any purpose other
than cooking. It could result in fire or damage to
the appliance due to overheating or abnormal
combustion.
•
Do not touch the hot parts such as top plate,
skewer holders, heat-resistant glass, griddle and
grate during and immediately after use. Do not
bring your face or hand near the grill surface to
avoid contact with hot exhaust heat. Failure to
observe this caution can result in burn injury.
•
Do not use any part other than genuine parts and
the parts supplied with this appliance. In particular,
do not use large iron griddle or ceramic plate of
such size that it can cover the whole grilling surface.
Use of such part can cause carbon monoxide
poisoning may occur due to imperfect combustion,
burn damage or fire due to overheating or abnormal
combustion.
•Precautions on water tray
•
Oil and fat deposited on the water tray may
catch fire and cause burn injury or fire damage.
•
Be sure to fill the water tray with water before use.
If the oil or fat deposited on the tray starts
splashing, be sure to replace water on the
tray to remove oil and fat.
THINGS YOU NEED TO PAY ATTENTION
•
Do not cover the griller with towel or newspaper
after use.
This appliance is for commercial use
•
This appliance is for commercial use.
Do not use for dosmetic purpose.
•
In case of change
of user, be sure
to let the new
user to read this
Manual and
understand the
contents thoroughly
before use.
4

Ensure that the type of gas (gas group) supplied is
same as the one mentioned on the nameplate at
the right side of the griller.
Gas valve
•Prepare a dedicated gas valve for this appliance.
•If there is no gas valve in the installation location
or the gas valve is not appropriate, the gas valve
needs to be newly installed, relocated or replaced.
Consult your dealer or gas operator.
Gas connection
Check the type of
gas supplied
Gas connection
and installation
•Use a gas rubber hose only. Never use any vinyl
hose. (Vinyl hose is not resilient and vulnerable to
h eat.) The hose with any crack or loose connection
problem must be replaced with new one.
•
When a fuse cock is used, select the one appropriate
for the gas type and gas amount to be used.
Installation of back guard (RGK-64)
•
If the wall at the back of the appliance is flammable,
be sure to install the supplied back guard.
Insert
Rear
PREPARATION BEFORE USE
•
The connection port diameter is ø9.5mm hose end.
RGK-64: natural gas.
Gas other than LP gas: ø13mm hose end.
•Use a gas rubber hose and make it shorter as
much as possible (up to 2m with reasonable margin)
to avoid twist or bend. Do not place the rubber hose
under the griller. Avoid contact between hose and
the griller.
•Push the rubber hose onto the fitting up to the red
line and secure it with a hose clamp.
•Do not connect additional
rubber hose or branch
out the hose.
Example) 96.06 (Manufactured on June 1996)
(Model name)
(Manufactured date) (Serial No: YS)
(Distributor)
(Gas consumption)
<Nameplate>
Confirm the gas type
(Type of gas (gas group))
5

Installation location
•Stable, level location
Do not use this appliance in any unstable
or windy location.
•Location without a risk of
falling object
Do not use this appliance in a location
with a risk of falling object such as under
a shelf. The object fallen on top of it may
burn and cause fire.
•Location without flammable object
such as curtain and spray can
Do not use this appliance near curtain
or flammable object. These objects may
catch fire and cause fire damage.
•Install the appliance in a location with low
humidity to ensure durability.
•Install the appliance in a place with good
ventilation (both intake and exhaust). Be
sure to maintain good ventilation while in
use. Using this appliance in a closed
location for a long time may cause
imperfect combustion due to low oxygen
level and, which can result in carbon
monoxide poisoning.
•
Be sure to observe the precautions on installation to
ensure compliance with the Fire Prevention Ordinance.
Insufficient clearance around the appliance may result in
fire. Even if an inflammable wall is covered with the object
such as stainless steel plate, it is necessary to maintain
the same distance as required for combustible objects.
•
Do not refurbish the appliance’s surroundings after the
installation (such as enclosing the appliance, installation
of hanging shelf). Such a refurbishment may not be
compatible
with the installation standards or cause
imperfect combustion or fire.
•
If the wall around the appliance is flammable (such as
wooden wall), be sure to keep a distance of at least 20cm,
15cm (for RGK-62D, 20cm and above) and 100cm for
sides, rear and top respectively.
Safety distance to combustible
object and fire prevention
measures for the surroundings
Material Thickness Caution
Steel plate
Stainless steel plate
0.6cm and above
0.6cm and above
Ensure a space at least 3cm and provide adequate
reinforcement to prevent harmful deformation.
RGK-61D, 62D, RGB-60B
Gap between ceiling and side wall Gap between back wall side
RGK-64
Gap between ceiling and side wall
Combustible object Combustible object
Combustible
object
Combustible
object
20cm and above 20cm and above
100cm and above
Combustible
object
0cm and above 0cm and above
15cm and above
0cm and above
Gap between back wall side
•
If the distance of at least 20cm (sides), 15cm (rear) (for
RGK-62D, 20cm and above) and 100cm (top) is
unavailable between the appliance and flammable wall,
installation of a heat insulating plate is required as shown
in the illustrations on the right.
3cm and above
Combustible object Heat insulating plate
0cm and above 0cm and above
80cm and above
Combustible object Combustible object
Leave a gap
3cm and
above 0cm and
above
0cm and
above
0cm and
above
Leave a gap
0cm and
above
3cm and
above
Heat insulating plate
Heat insulating
plate height
50cm and
above
0cm and
above
100cm
and above
20cm and above
0cm and above
Combustible
object
20cm and above (RGK-62D)
15cm and above
0cm and above
Combustible
object
Heat insulating plate
Heat insulating plate
Gap 3cm
and above
Gap 3cm and above
50cm and
above
0cm and
above
Leave a gap
0cm and above
0cm and
above
0cm and above
80cm and
above
0cm and
above
Combustible
object Combustible object
RGK-61D, 62D, RGB-60B
RGK-64
Heat insulating plate
6

No. 61
NAMES OF EACH PARTS
RGK-61D
Grate
Top plate
Gas connection port
Burner control knob
Water tray
No. 62
RGK-62D
Griddle
No. 2
RGB-60B
Heat-resistant glass
Skewer holders
Skewer holders
7

•There are glass holders on both sides of the
burner. Place the heat-resistant glasses on
the holders. If the glass does not sit properly,
change the right and left glass.
No. 64
RGK-64K
Installation of parts and adjustment step
Remove the papers/packaging materials and install the appliance correctly.
Heat-resistant glass
Note
Caution)
Glass surface
may be slightly
unevenly colored
but this does not
affect its function
and food safety.
You may use the
glass safely.
•Place the griddle properly
on the griddle holders
located on both sides of the
top plate. (The burners will
not ignite if the griddle is
not installed properly.)
Griddle (RGB-60B)
Griddle
Griddle
holders
•Place the skewer holders on the front and back
side of the appliance. To raise the height of
skewer holders, place square bars or pipes on
both sides and then place the skewer holders
on top of them. The grate must be placed on the
skewer holders to use it.
Skewer holders
(RGK-61D, 62D, RGB-60B)
(RGK-64)
Rear (Left)
Water tray
Grate
Back guard
Top plate
Burner control knob
Skewer holders
Skewer holders
Heat-resistant glass
Skewer holders
(RGK-61D, 62D)
Heat-resistant glass
Glass holders
(RGK-64)
Heat-resistant glass
Glass holders
Gas connection port
8

Preparation
•Make sure that the burner control knob is at
the “OFF” position and then fully turn on the
gas valve.
•Fill the water tray with water until the water level
indication.
WARNING
•If the griller is used without filling the water
tray with water, the oil and fat deposited
on the water tray may catch fire.
Be sure to fill the water tray with water to
approximately half level before use.
•During use, make sure from time to time
that the water tray is filled with water
without a lot of oil and fat deposited. If the
oil or fat deposited on the tray starts
splashing, be sure to replace water on the
tray to remove oil and fat. If the water tray
is used without replacing water, the
splashed oil and fat may catch fire. Caution
should be exercised during water replacement
as the water tray may be very hot.
•Push the burner control knob and slowly turn
counterclockwise (towards ON direction) until
it stops.
•A click sounds and the pilot burner is ignited.
Keep the knob pushed in and turned for a few
seconds until the main burner is ignited.
•Release your hand from the burner control
knob only after making sure that the main
burner has been ignited.
•The burner control knob slightly returns up to
“ON” position.
•Wipe the main unit with a clean cloth.
•Wash the grate and water tray using neutral detergent
and then wipe them with a clean cloth.
Verification
•The rubber hose is not cracked, excessively
bent or in contact with the griller.
•No flammable object such as paper, plastic,
oil and spray can is placed near the appliance.
•The heat-resistant glasses are properly placed
on the glass holders.
•The griddle is properly placed on the griddle
holders. (RGB-60B)
HOW TO USE
Preaparation and
Verification Before
Ignition
Ignition
When using this appliance for the first time
(OFF)
(ON)
(OFF)
(ON)
When the burners are ignited for the first time,
the ignition may not be smooth due to the air
trapped in the rubber hose. In this case, repeat
the ignition operation few times until the air is
released. If the ignition attempt fails, turn the
burner control knob back to the original position
and then make another ignition attempt. Ignition
may fail if the knob is turned too fast.
9

Flame control
• In the case of high heat grill, lower the grill
height while maintaining the burner control
knob at “ON” position.
• In case of low heat grill, raise the grill height
while maintaining the burner control knob at
fully turned position. (If gas is turned down too
much, fat from fish, etc. easily adheres to the
heat-resistant glass or griddle and more smoke
is generated. This may also cause imperfect
combustion.)
Re-ignition
• Slowly turn the burner control knob counter-
clockwise (towards ON direction) until it stops.
• When re-igniting immediately after extinguishing,
wait for about 5 seconds before the next ignition
attempt.
•Make sure that the burner control knob is at the
“OFF” position and shut off the gas valve fully.
•
Do not cover the griller with towel or newspaper.
Extinguishment
•Turn the burner control knob clockwise fully
(up to the “OFF” position).
(OFF)
(ON)
•Make sure that the main burner has been
extinguished.
After use
•Do not bring your face too near the burner
during ignition. Burn injury on the face may
occur due to flame or heat.
Caution on high
temperature
WARNING
10

DAILY INSPECTION AND CLEANING
First of all, make sure that:
1 the gas valve is shut off 2 the griller has been cooled down.
WARNING
•Users other than repair personnel must never
disassemble, repair or modify this appliance.
Failure to observe this warning may result in fire,
gas leakage or injury due to malfunction.
Disassembly
prohibited
•Do not put water on the appliance. It could
result in incomplete combustion.
Inspection
• Check if a gas rubber hose is used and connected to the griller as well as the gas valve properly up to the
red line.
• Check for gas leakage from the gas connection from time to time using soap water, etc.
• Check if any combustible object such as paper, plastic and spray can is placed near the appliance.
• Make sure that the heat-resistant glass or griddle is properly installed.
• Check if a lot of oil and fat is deposited on the water tray from time to time. If the oil or fat deposited on the
tray splashes during use, replace the water on the tray.
Cleaning (Be sure to wear gloves when cleaning to prevent injury.)
Usable tools
Unusable tools
•Neutral kitchen detergent •Soft cloth •Sponge
•Acidic detergent, alkaline detergent
•Cleanser (Scrubbing powder)
•Alcohol, thinner, benzene
•Metal brush, Nylon brush, metal spatula
A caution label containing safety information is pasted on the main unit. If the label is dirty and
unreadable, wipe the appliance with a soft cloth and watch out for the label when cleaning. If the label is
peeled off or unreadable, contact your dealer or any Rinnai office for repurchase and re-paste of the label.
Note
•Main unit, top plate
•Wipe well with a dry cloth. In case of stubborn dirt, clean with a cloth dampened with neutral detergent
solution, wipe off the detergent adequately and then wipe with a dry cloth. Damage may be promoted if
the dirt is left untreated.
11

To ensure long life of heat-resistant glass (RGK-61D, 62D, 64)
•The best way to ensure long life of the heat-resistant glass is to clean it (wash with water) frequently.
Adequate effect is achieved even just by washing it under pouring water while cooking or washing it with
water after cooking. The heat-resistant glass has a tolerance to heat shock at 650°C and it will not break
even if water is poured onto it during cooking. Wash off organic acid (such as soy sauce) on the glass
while cooking by occasionally pouring water on it. (Be careful not to get burn when pouring water onto
the heat-resistant glass while cooking)
•After use, wash off the oil/fat, dirt and salt on the glass well
with water or warm water using a cloth or sponge.
•The heat-resistant glass will not break even if water is poured
onto it during cooking. Wash off the dirt on the glass while
cooking by pouring water on it by way of spray, etc.
Be careful not to pour water on the heating
surface of the burner.
•Reinstall the glass properly after cleaning.
(Read page 8 for details.)
About consumable parts
Contact your dealer or any Rinnai office for purchase of consumable parts.
•Heat-resistant glass (RGK-61D, 62D, 64)
Damaged heat-resistant glass can cause uneven grilling, damage to the appliance or imperfect
combustion due to oil and fat or dirt dropped directly onto the heating surface of the main
burner. If the heat-resistant glass is damage, purchase a new heat-resistant glass.
•Griddle (RGB-60B)
Deformed or damaged griddle can partially affect the red heat or cause difficulty in ignition.
If the use of the griller is likely to be affected by this problem, purchase a new griddle.
•Grate, water tray, skewer holders
Purchase a new grate, water tray and skewer holder if any of these parts is deformed or
damaged to the extent that the use of the griller is likely to be affected.
•Burner (RGK-61D, 62D, 64)
•Do not apply impact or pour/spill water onto the heating surface (main burner).
•Water tray, grate
•Clean the dirt with neutral detergent and wipe off the water well with a dry cloth.
•Reattach them to the main unit after cleaning.
•Griddle (RGB-60B)
•Wash off the oil/fat and dirt on the griddle with a cloth dampened with
neutral detergent solution. (Dirt comes off easily if the dirt is moistened
with detergent solution before cleaning.)
•After cleaning, wipe off the water well and reinstall the griddle properly.
•Burner (RGB-60B)
•Do not spill or splash water onto the burners. (If the burner does
not ignite due to water, wipe off the water on the flame holes with
a dry cloth and ignite again.)
•If the griddle does not become red hot enough, clean the flame
holes with a wire.
Heat-resistant
glass area
12

WARNING
If you notice something abnormal while in use, immediately stop using
this product and shut off the gas valve.
Symptom
The flame is not ignited.
It is hard to ignite. •Is the gas valve fully opened?
Cause
It is hard to ignite (from
pilot burner to main burner)
Explosion-like ignition
The burner does not turn
red when heated.
•Is the gas valve fully opened?
•Is the heat-resistant glass
(griddle) properly installed?
•Is the heat-resistant glass
(griddle) damaged?
•Is the flame holes on the
burner clogged?
•Fully open the gas valve.
(
When LP gas is used, check the gas
level in the cylinder.)
Action to be taken
•Fully open the gas valve.
•Installed the heat-resistant glass
(griddle) properly.
•Replace the heat-resistant glass with
new one.
•Clean the clogged flame holes on the
burner.
The flame goes off while
using.
•Is the burner control knob fully
opened?
•Is the gas valve fully opened?
•Is the heat-resistant glass
(griddle) properly installed?
•Is the heat-resistant glass
(griddle) deformed or
damaged?
•Is the flame holes on the
burner clogged?
•Fully open the burner control knob
when using.
(When LP gas is used, check the gas
level in the cylinder.)
•Fully open the gas valve.
•Installed the heat-resistant glass
(griddle) properly.
•Replace the heat-resistant glass with
new one.
•Clean the clogged flame holes on the
burner.
If the problem still persists even after you have checked the above items, stop using the griller immediately
and contact your dealer or any Rinnai office.
FAULT/ERROR IDENTIFICATION AND REMEDY
DIMENSIONS (Unit : mm)
RGK-62D
No. 62
RGB-60B
No. 2
Back guard
height
RGK-64
No. 64
RGK-61D
No. 64
13

Model name
Infrared Gas Griller (Lower Flame Type)
Model no.
Type
Ignition system
Dimension
(mm)
Weight (kg)
Accessories
Gas
connection
(W) 606.5mm x
(D) 209.5mm x (H) 216mm
SPECIFICATIONS
RGK-61D RGK-62D RGK-64,
RGK-64-1, RGK-64-2
RGB-60B-10
RGB-60B-20
Lower Flame Type
Piezo
(W) 581mm x
(D) 324.5mm x (H) 240mm
(W) 1020mm x
(D) 337.5mm x (H) 344mm
(W) 606.5mm x
(D) 209.5mm x (H) 216mm
7.5 12 29 4.0
ø9.5mm gas rubber hose
Natural gas, LP gas
ø9.5mm gas rubber hose
Natural gas, LP gas
ø9.5mm gas rubber hose
Skewer holders (2 pcs), Grate [RGK-61D, 62D, RGB-60B (1 pc), RGK-64 (2 pcs)],
water tray (1 pc), back guard (1 pc) (RGK-64), operation manual
GAS CONSUMPTION (Gas consumption per hour)
RGK-61D, 62D RGB-60B
Model no.
Gas group
RGB-60B-10 (For LP gas)
RGB-60B-20 (For natural gas)
RGK-64
For LP gas
Gas group
For LP gas
For natural gas
The specifications are subject to change without notice for improvements.
For natural gas 2.44kW/
8325.62 BTU
4.88kW/
16651.25 BTU
3.49kW/
11908.37 BTU
2.52kW/
8598.59 BTU
5.04kW/
17197.19 BTU
3.78kW/
12897.89 BTU
10.0kW/34121.41 BTU
Model no. Gas consumption per hour
10.0kW/34121.41 BTU
14

RINNAI (MALAYSIA) SDN. BHD. (015790-A)
D2-3-G & D2-3-1, Block D2,
Pusat Perdagangan Dana 1,
Jalan PJU 1A/46, 47301 Petaling Jaya,
Selangor Darul Ehsan, Malaysia.
Tel: [phone] & 03-7832 0039
Fax: [phone] Website: www.rinnai.com.my