Rinnai SG2152HP User manual
Solar Split System
Installation Manual
Must be installed, commissioned and serviced by an authorised
person in accordance with all applicable local rules and regulations.
Power supply must be available to the system at all times
•
•
SOLAR COLLECTOR Domestic Application Commercial Application
Parts 7 years 5 years
1 year 1 year
RINNAI INFINITY:
Domestic models (white)
Domestic Application Commercial Application
Parts 10 years pro rata 1,500 hours or 1 year*
3 years 1,500 hours or 1 year*
Parts 3 years 1,500 hours or 1 year*
3 years 1,500 hours or 1 year*
RINNAI INFINITY:
Commercial models (silver)
Domestic Application Commercial Application
Parts 12 years pro rata 5,000 hours or 3 years*
3 years 1,500 hours or 1 year*
Parts 5 years 1,500 hours or 1 year*
3 years 1,500 hours or 1 year*
STORAGE TANK Domestic Application Commercial Application
Parts 5 years 3 years
3 years 3 years
Parts 1 year 1 year
1 year 1 year
* Pumps, controllers, valves etc.
Domestic vs. commercial application
notice.
warranty does not limit any consumer rights or guarantees that may apply under the
Water quality for Rinnai Innity and solar collectors
TDS
(Total
Dissolved
Solids)
Total
Hardness
CaCO3
Alkalinity
(as CaCO3)
Dissolved
(free) CO2
pH Chlorides Magnesium Sodium Iron Langelier
Index
Up to 600
ppm
Up to 200
ppm
Up to 200
ppm
Up to 25
ppm
Up to 300
ppm
Up to 10
Up to 150
ppm
Up to 1
ppm
In relation to solar collectors
changes to the temperature mode settings are not covered.
•
•
•
In relation to storage tanks
•
•
1.
2.
3.
4.
5.
6.
7.
a.
b.
WARNING
Improper installation, adjustment, alteration, service or maintenance
Introduction 6
6
7
10
Mounting the solar controller and pump 11
13
15
20
21
22
23
6
Water quality
Hard or aggressive water will need to be treated in order to use this product.
Water pressure
Roof pitch and condition
Pumped systems only
Introduction
•
•
7
Hot outlet connection
Stainless steel straps for tile roofs
straps can be purchased as an accessory item.
Included Not included (to be supplied by the Installer)
Straps
•
•
•
•
•
•
•
•
Example of the solar collector ttings for a two solar collector installation
Pump provided in kit
Tempering valve
to handle the higher temperatures.
Pipe insulation
tape.
Dip tube to solar enable tank
Included Not included (to be supplied by the Installer)
Pump
tube
•
•
•
•
•
•
•
•
•
•
Pump and Solar Panel
•
•
•
•
•
•
•
•
•
•
•
Inside or
outside
inside or outside.
where appropriate.
restrained against seismic activity.
building elements in order to gain access.
and controller
1
It is important to discuss the timer with the customer as they will need to
Relevant
regulations
Base
requirements
Access to
cylinder
Catch pan
Electrical
connections
Timer for
electric boost
systems
10
Pressure
limiting valve
Cold water
pressure relief
valve
Temperature
& pressure
relief valve
(TPR)
[supplied with cylinder]
[supplied with cylinder]
Drain valve
Drain lines
Tempering
valve
range to handle the higher temperatures.
11
Mounting the solar controller and pump
1.
2.
3.
12
Mounting the solar controller and pump
pump is installed correctly with the impeller in a vertical not horizontal position.
protection.
is not available.
4.
5.
6.
7.
Solar Control Box with Switch Positions Marked
Solar Controller Settings
CIRC/DUMP FPOFF/FPON
IMPORTANT
Frost Protection - Electricity Required Label
13
connections.
minimised.
Solar water heaters must be located away from the edge of the gable roof
structure outside the high pressure wind zone as shown.
Cold
connection
Hot
connection
Each collector must slope upwards 8-10 mm
occur.
Roof sizing and
collector weight
Roof inspection
required before
installation
Collector angle
and positioning
14
Hot collectors
gloves must be used to prevent burns.
system is complete.
Pipe
connections
between
collector and
tank
or other coating
collector is 50 m
WARNING
15
Check purlin
size
Position top
collector
Fasten top
mounting rail
1.
2.
3.
possible and be evenly distributed across them.
Mark
position for
strap hooks
and secure
4.
washers underneath to avoid direct contact between the strap and the
16
Fit lower
mounting rail
to the straps
5.
Fit additional
straps as
required
6.
17
Fit
collectors
7.
Fit
additional
collectors
8.
inserting the header tubes into the connectors and attach the collector to
Use lower holes
straps can be purchased as an accessory item.
Determine position for top mounting rail
across them.
the determined position.
slightly to prevent this happening.
to be level
Attach
plumbing
ttings
Run piping
and insulate
Insert hot
sensor lead
1.
2.
copper tube.
temperature silicon.
connector on the solar controller.
2
Rinnai Solar Collector Fittings Kit Assembly - Two Collectors
Hot sensor lead
20
water heater must be set to 75 o
o
o
•
•
instantaneous water heater must heat all water passing through it to not less than 70
Recommended system layout using a Rinnai Innity and ow diversion valve
Table of contents
Other Rinnai Water System manuals
Rinnai
Rinnai PRESTIGE User manual
Rinnai
Rinnai Circ-Logic Series User manual
Rinnai
Rinnai Enduro SP200A User manual
Rinnai
Rinnai INFINITY 26 User manual
Rinnai
Rinnai PRESTIGE User manual
Rinnai
Rinnai EHPA250VMAH User manual
Rinnai
Rinnai Enduro XL SP250B User manual
Rinnai
Rinnai HD210i User manual
Rinnai
Rinnai Infinity Series User manual
Rinnai
Rinnai E-Frost User manual
Popular Water System manuals by other brands
EcoWater
EcoWater CHC Installation & service manual
Pure Water
Pure Water WATT'R TWIN Owners and installation manual
mysoda
mysoda WOODY instruction manual
Astral Pool
Astral Pool Heliox MP 50W Installation and maintenance manual
Waterco
Waterco OXISWIM Installation and operation manual
FujiClean
FujiClean CE installation manual
Puretec
Puretec SH SERIES user guide
Everpure
Everpure QCP Single Head EV9107-21 Specification sheet
Armstrong
Armstrong ASTRO 2 SERIES Installation and operating instructions
LifeSource
LifeSource 810 Series Installation and operation guide
Graf
Graf one2clean Service instructions
EcoWater
EcoWater ESD 518 owner's manual
