Ritelite RITE-POWER 1750 User manual

This user manual covers the Rite-Power 1750 / 1750x2 / 3850 / 5250 / 7700 /8000
industrial portable power generators with the following product options:
110V | 230V | Type F | T60309 sockets
The information contained in this manual is based on products manufactured up to the time of publication.
Ritelite (Systems) Ltd reserves the right to change any of this information without notice.
No part of this manual may be reproduced in any form or by any means, electronic or mechanical without express written
permission from Ritelite (Systems) Ltd.
Any type of reproduction or distribution not authorized by Ritelite (Systems) Ltd represents an infringement of valid copyrights,
and violators will be prosecuted. We expressly reserve the right to make technical modifications, even without due notice,
which aim at improving our products or their safety standards.
Product Resources
RITE-POWER 1750 / 1750x2 / 3850 / 5250 / 7700 / 8000
750W / 2500W / 4000W | 110V / 230V
Operator’s Manual

2
IMPORTANT INFORMATION ABOUT YOUR
RITE-POWER
PORTABLE BATTERY POWERED GENERATOR
Use this page to record important information about your RITE-POWER unit.
This information can be found on your RITE-POWER data plate which is found next to the mains outlet socket
on the side of the units.
NOTE: Below is an example of a RITE-POWER data plate.
UNIT PRODUCT REFERENCE
UNIT SERIAL NUMBER
You will be required to supply the products serial number when contacting Ritelite (Systems) Ltd or one of
Ritelite’s approved dealers about parts and service.
OUTPUT
230V AC 50Hz
Max continuous output 2500W
RITELITE (SYSTEMS) LTD
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS 715mm (L) x 370mm (W) x 680mm (H) WEIGHT 91Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODES LK1770BP7700/2400/230/T60309
MAX CONTINUOUS OUTPUT POWER 2500W
IP RATING IP44
RITE-POWER 7700 PORTABLE BATTERY POWERED GENERATOR
A-262n2
Made in the UK
Product contains a lithium battery which must be disposed of correctly

3
CONTENTS
SECTION TITLE PAGE NUMBER
Section 1: Introduction & applications for use 4
Section 2 : Safety rules 5
Section 3: Technical specifications 9
Section 4: Setting up the RITE-POWER generator 13
Section 5: Operating instructions 14
5a) Pre-operation inspection 14
5b) Using the RITE-POWER generator 17
5c) Recharging the RITE-POWER generator 20
5d) Optional ‘Pass through’ power transfer system 22
5e) Packing away and transport 24
5f) Storage / transport mode 24
Section 6: Troubleshooting 25
Section 7: Maintenance 27
7a) Advice on disposal 27
7b) Disclaimer of warranty 27

4
Section 1: INTRODUCTION & APPLICATIONS FOR USE
The RITE-POWER generator is designed as an industrial portable power generator supplying continuous AC
mains power up to 750W or 2500W or 4000W for equipment requiring 230V AC 50hz or 110V AC 60hz,
depending on
model chosen.
It uses bespoke Lithium batteries with a dedicated battery management system to supply a pure sine wave
inverter producing a clean reliable supply, powering most equipment up to 750W or 2500W or 4000W
(depending on model).
It is housed in a ruggedised waterproof case with industrial input and output sockets for charging and taking
power from the unit. Note some options include the charger contained within - on these connect the supplied
mains input cable for recharging.
In addition, a display on the outer case indicates run times based on the current load, recharge time based
on the current charger connected and other information pertaining to the battery voltage, current, state of
charge and capacity. A single switch turns the system on and off and contains a red warning LED
to indicate any fault conditions including low battery supply, over temperature, overload and
short circuit.
Some models are fitted with a battery isolator switch. Turn off when not in use to prevent unnecessary
battery discharge. Turn on for operation, Isolator can be switched off if only recharging is required.
All users must read, understand and obey any instructions and information contained herein these operating
instructions before use. Only trained or competent personnel should use the RITE-POWER generator.
This manual should always stay with the RITE-POWER generator.
APPLICATIONS FOR USE
The RITE-POWER generator is designed for use in the following applications only. It should not be used for any
other purpose. If in any doubt about applications for use, please contact either Ritelite (Systems) Ltd or Ritelite
(Systems) Ltd’s distributor for more information.
• Powering resistive load equipment up to a max continuous load of 750W (1750 and 1750x2 models),
2500W (3850, 5250 and 7700 models) or 4000W (8000 models).
• Powering capacitive load equipment up to a max continuous load of 750W (1750 and 1750x2 models),
2500W (3850, 5250 and 7700 models) or 4000W (8000 models).
• Avoid Powering Inductive loads (Items with motors in) or limit their load to 500W Max (200W for 1750
and 1750x2 models or 800W Max for 8000 models). Note some loads may fail to run at all from the RITE-
POWER Generator or cause the inverter system within the generator to behave abnormally causing it to
shut down, if this happens disconnect the load and don’t attempt to retry.
Failure to follow the instructions and safety rules in this manual may result in death or
serious injury.

5
Section 2: SAFETY RULES
It is important that every user understands and observes the safety rules
before setting up or using the RITE-POWER Portable Battery
Powered Generator.
The Manufacturer, Ritelite (Systems) Ltd cannot anticipate every possible circumstance that might
involve a hazard. The warnings in this manual and on labels affixed to the RITE-POWER generator
will therefore not cover every eventuality. If using a procedure or operating method not specifically
recommended by the manufacturer then the user must verify that it is safe for others and that it does not
make the equipment unsafe.
Throughout this manual and on labels on the RITE-POWER generator, DANGER, WARNING and
CAUTION blocks are used to alert personnel to special instructions about a particular operation that
may be hazardous if performed incorrectly or carelessly. Observe them carefully. Their definitions are
as follows:
Indicates a hazardous
situation which, if not
avoided, will result in
death or serious injury.
Indicates a hazardous
situation which, if not
avoided, could result in
death or serious injury.
Indicates a hazardous
situation which, if not
avoided, could result in
minor or moderate injury.
These safety alerts cannot eliminate the hazards that they indicate.
Common sense and strict compliance with the instructions within this
manual are essential to preventing accidents.

6
When using the RITE-POWER generator indoors or outdoors, basic safety
precautions should always be followed to reduce the risk of fire, electric shock and
personal injury including the following:
a) Ensure the IP rating of the connecting plug to coupler application is suitable
for the prevailing conditions.
b) Read and understand the implications from the MSDS (Material
Safety Data Sheet) for the product, for both use and transport/
shipping. The MSDS can be viewed the following link or by
scanning the QR code on the right:
https://ritelite.co.uk/product-resources/rite-power/
c) Do NOT allow the RITE-POWER generator to become submersed under
water or allow any liquid to enter inside the product.
d) Use only with an extension cord appropriate for outdoor use.
e) Do NOT use damaged cables or connectors.
f) All cables and equipment must be double insulated.
GENERAL SAFETY RULES & POTENTIAL HAZARDS WHEN
SETTING UP AND USING THE RITE-POWER PORTABLE
POWER GENERATOR
FALL HAZARDS
• Do NOT place the RITE-POWER generator anywhere it could fall on to personnel.
• Do NOT stand on the RITE-POWER generator or use it as any form of step.
TIP OVER HAZARDS
• Where ground or the area is uneven place the RITE-POWER generator on its base to ensure it
can’t fall over.
• Prior to setting up check the area for any possible hazardous conditions.
• Do NOT place ladders or scaffolding against any part of the RITE-POWER generator.
• Do NOT use the RITE-POWER generator on a moving or mobile surface without strapping it
down to prevent unexpected movement.

7
• Use the integrated handles or optional trolley (SLK1770BP/TROLLEY or SLK1770BP/
TROLLEY/HC) to safely carry/move the RITE-POWER generator (for models 3850, 5250,
7700 and 8000).
• Do NOT use the RITE-POWER generator for any purpose other than that for which it
is designed.
ELECTROCUTION HAZARDS
• Do NOT allow the inside of the RITE-POWER generator to come into contact with water or
any other liquids.
• Ensure the RITE-POWER generator is not being set up in a potentially explosive environment
– the RITE-POWER generator is not an ATEX approved product.
• The RITE-POWER generator is not designed to be submersed under water.
• Do NOT use if any parts become significantly damaged which may compromise the IP rating
of the product.
• Do NOT use if any damage to the sockets on the product occurs.
• If any significant damage occurs the RITE-POWER generator must be returned to Ritelite
(systems) Ltd or one of its authorized dealers for repair.
• Do NOT use plugs or cables that are cut or damaged in any way.
• Do NOT connect the RITE-POWER generator to any other mains supply system such as a grid
or generator supply, it is not designed for grid tie systems, it will damage
the unit.
• Do NOT allow minors or persons of reduced competency to use the RITE-POWER generator,
it is NOT a toy.
• Do NOT connect the RITE-POWER generator charger between its charge input and mains
outlet sockets, it will damage the unit.
BODILY INJURY HAZARDS
• It is recommended that the user wears gloves whilst manoeuvring or connecting up the RITE-
POWER generator.
• In slippery or uneven terrain, it is recommended that two people manoeuvre the product at
all times.
• The RITE-POWER generator is designed to be simple to operate by one person however
there may be situations where it is recommended that two people manoeuvre the product.
• Do not manoeuvre the RITE-POWER generator product for long distances in
extreme temperatures.
• Where possible the RITE-POWER generator should be set up away from personnel or
moving vehicles.

8
CRUSHING HAZARDS
• Ensure the RITE-POWER generator is set up on a firm and horizontal flat surface.
• Keep hands and fingers away from any potential pinch points.
• Never place the RITE-POWER generator above personnel where it could fall on them.
COLLISION HAZARDS
• Use common sense and planning when transporting/carrying the RITE-POWER generator on
any incline or slope.
• On slippery or uneven terrain, it is recommended that two people manoeuvre the product at
all times.
• Make sure when loading the RITE-POWER generator into a vehicle or trolley that it is securely
mounted/retained so it cannot fall off or move in such away that it could harm other items
or personnel.
DAMAGED MACHINE HAZARDS
• Do NOT use a damaged RITE-POWER generator or one that isn’t working properly.
• Conduct a thorough pre-operation inspection prior to each use.
• Be sure that all labels are in place and legible.
• Do NOT use if there are any visible damaged parts. Contact your original point of purchase or
Ritelite (Systems) Ltd to arrange for spares or repair options.
• Do NOT use any type of abrasive or strong chemicals to clean the
RITE-POWER generator.
• Do NOT attempt to defeat / modify any of the wiring or protection fuses.
IMPROPER USE HAZARD
• Never leave an RITE-POWER generator unattended unless a full risk assessment for the
application it is being used for has been undertaken by a competent person. Unauthorized
personnel could attempt to operate the RITE-POWER generator without proper instruction
potentially causing injury to themselves or others.
• The RITE-POWER generator is to be used only for its prescribed purpose. Any use other than
that mentioned is considered to be a case of misuse.
• The user/operator, and not the manufacturer shall be liable for any damage or injury resulting
from such cases of misuse.
• It is imperative to observe the local accident prevention regulations.
• The same applies for the general rules of occupational health and safety.
• The manufacturer is not liable for indirect consequential damage and financial loss.
• The manufacturer shall not be liable for any changes made to the device nor for any damage
resulting from such changes.
• The RITE-POWER generator is not designed to be setup/used on a live public highway.

9
RITE-POWER MODEL KEY SPECIFICATION
1750
1750 watt hour battery capacity
750W continuous power
Pure sine-wave inverter energy
110V / 230V options
3 charger options
22kg one person lift
Dimensions: 57 x 36 x 24cm
Rated IP65
1760x2
3500 watt hour battery capacity
750W continuous power
Pure sine-wave inverter energy
110V / 230V options
3 charger options
36kg two person lift
Dimensions: 58 x 40 x 30cm
Rated IP65
3850
3850 watt hour battery capacity
2500W continuous power output
Pure sine-wave inverter energy
110V / 230V options
3 charger options
52kg
Dimensions: 72 x 37 x 47cm
Rated IP44
5250
5250 watt hour battery capacity
2500W continuous power
Pure sine-wave inverter energy
110V / 230V options
3 charger options
Built-in charger option
57kg two person lift
Dimensions: 68 x 34 x 68cm
Rated IP44
7700
7700 watt hour battery capacity
2500W continuous power output
Pure sine-wave inverter energy
110V / 230V options
3 charger options
91kg
Dimensions: 72 x 37 x 68cm
Rated IP44
8000
7700 watt hour battery capacity
4000W continuous power output
Pure sine-wave inverter energy
110V / 230V options
3 charger options
96kg
Dimensions: 74 x 39 x 75cm
Rated IP44
Section 3: TECHNICAL SPECIFICATIONS
Custom battery generator options are available, these may differ in specification to the above.

10
PHYSICAL
Case Material: Lightweight NK-7 resin (1750, 1750x2)
Powder coated aluminium (3850, 5250, 7700, 8000)
Protection Class: IP65 (1750, 1750x2) IP44 (3850, 5250, 7700, 8000) - (Subject to the product
being set up vertically on its supporting feet and not submersed in liquid).
Operating ambient temperature range: 0 deg - +30ºC
Recommended storage temperature: 0 to +25ºC
ELECTRICAL
Output - 110V 60HZ 750W, 2500W or 4000W Max, or 230V 50HZ 750W, 2500W or 4000W
Max AC
(depending on model selected)
Output voltage tolerance +/- 5%
THD < 3%
Efficiency > 90%
Power Factor 0.99
Mains output socket
CEE 110V 16A 3P IP67 Socket
or
CEE 230V 16A 3P IP67 Socket
or
SCHUKO OUTLET SOCKET 250V 16A 3P IP68 -F
CHARGING
Via CEE 32A 2P IP67 Socket – use only the following Ritelite (Systems) Ltd model range –
SLK350CH, SLK750CH & SLK1000CH.
Note this socket is only for charging and must NOT be used for discharging or any other purpose
than the sole connection of the SLK350CH, SLK750CH & SLK1000CH model chargers.
Note some models are fitted with a battery isolator switch. Turn off when not in use to prevent
unnecessary battery discharge. Turn on for operation, Isolator can be switched off if only
recharging is required.
Isolator knob can be removed to prevent unauthorised operation.

11
PROTECTION SYSTEMS
• Short Circuit Protection – The RITE-POWER Generator will shut down until the fault is
removed. It will signal this by flashing the red LED continuously and a beeper will be heard.
• Overload Protection – The RITE-POWER Generator will shut down until the load is reduced.
It will however allow small overloads up to 120% for short periods of time up to a minute. It
will signal this by flashing the red LED continuously 5 times which will then be repeated and a
beeper will be heard until the fault condition is removed.
• Over Temperature Protection – The RITE-POWER Generator will shut down until it has cooled
sufficiently to allow it to function again It will signal this by flashing the red LED continuously 4
times which will then be repeated and a beeper will be heard until the fault condition
is removed.
• Low Battery Voltage – The RITE-POWER Generator will shut down until the battery has been
recharged sufficiently It will signal this by flashing the red LED continuously and a beeper will
be heard until the unit is switched off or recharged.
• Low Battery Capacity Shut Off – The RITE-POWER generator has shut down due to insufficient
battery capacity. It will signal this by flashing the red LED continuously twice which will then
be repeated and a beeper will be heard until the unit is switched off or recharged.
• Automatic shut down - The RITE-POWER Generator will automatically switch the inverter
output off if no load or a small load is detected aer 12 hours. Switch power button off then
on to reset unit to resume normal function.
• Over Voltage Protection – The RITE-POWER Generator will shut down if the voltage from
the battery/charger rises above a particular threshold, if this happens this would suggest a
permanent fault in the charging system or an incompatible charger has been connected, the
issue should be investigated by a competent person – please contact Ritelite (Systems) Ltd or
its authorised distributor. It will signal this by flashing the red LED continuously 3 times which
will then be repeated and a beeper will be heard until the fault condition is removed.
Note in most cases the inverter will automatically reset itself aer a fault condition has been
removed, in some cases it may be necessary to switch off then back on the power switch to
reset the unit.
The RITE-POWER generator is fitted with an appropriate 110V or 230V 30mA RCBO to add an
additional layer of protection over that mentioned above. However, all these protection systems
can’t mitigate against all dangers and situations. Please see the HSE document 482/2 https://
www.hse.gov.uk/foi/internalops/ocs/400-499/oc482_2.htm which should be strongly
considered and the appropriate risk assessments made to protect all users and those likely to
come in to contact with the mains power generated by the RITE-POWER generator. There is
particular onus on regular inspection of cables, plugs, sockets and equipment connected by a
competent person to make sure any likely hazards are significantly reduced. Appropriate cables,
plugs, sockets and equipment must be used for the environment in which the RITE-POWER
generator is to be used.

12
GUIDANCE ON EARTHING AND PROTECTING USERS
The RITE-POWER battery generator references the neutral to the earth system. This allows the
RCBO fitted help protect users as much as reasonably possible in the event of a fault occurring
with cables and/or equipment connected to the output.
In addition, there is an external earth point (Next to the outlet socket) on the product that can
be connected to true earth using a suitable recognised earth cable, please seek the advice of a
qualified electrician if this is to be done. Feasible methods for true earth connections are:
1) An earth rod driven to a depth of not less than 1 metre.
2) The earth terminal of an adjacent fixed installation.
3) Permanent Structural steelwork.
4) Exposed reinforcement bars in concrete foundations or structures.
5) A suitable metal structure known to be earthed.
It should be stressed that it is paramount to use equipment and cables suitable for the
environment they are to be used in to make sure a user can be afforded the maximum protection
against the likelihood of electrical shocks especially in harsh environments where cables and
equipment are subjected to far more physical damage.
Consideration should be given for environments where water is present or could be present
from rain or other liquids from elsewhere. Equipment and cables, plugs and sockets should be
examined regularly for signs of damage, both physically or through water ingress. Regular PAT
(Portable Appliance Testing) should be done according to the associated risks in the environment
the equipment is to be used.
The RITE-POWER Generator and equipment powered from it should be inspected before and
aer use and those inspections documented. If any damage or concerns are highlighted, then
the RITE-POWER Generator and/or equipment must be taken out of service and marked up
accordingly so it can’t be used until repair/inspected by a suitable qualified person.

13
Section 4: SETTING UP THE RITE-POWER GENERATOR
Inspect the proposed area for use.
An inspection of the proposed area in which to set up the RITE-POWER generator is necessary to
ensure it is suitable for safe operation. This inspection should be performed by the operator prior
to using the RITE-POWER generator.
The area should be free from moving vehicles, machinery, pedestrians or other factors which may
mean the RITE-POWER generator could form a hazard.
Set the RITE-POWER generator up in such a way that it cannot obstruct walkways or areas that
form emergency exit routes.
Do not leave unattended if there is potential for minors or non-competent persons to tamper with
the RITE-POWER generator whilst in use.
Operators should be aware of the following possible hazardous situations. The operator
should also remember these hazards, watch and avoid them while moving, setting up and
operating the RITE-POWER generator.
• Forming a trip hazard
• Mains electricity at 110V AC or 230V AC (depending on model) is produced by
this product.
• Minors or non-competent persons
• Debris either on proposed site or on route to site
• Inadequate surface support to withstand the RITE-POWER generator weight
• Water which could allow the RITE-POWER generator to be submersed
• All other possible unsafe conditions

14
Section 5: OPERATING INSTRUCTIONS
Do not use the RITE-POWER generator for any purpose other than that for which it is designed – as
a portable mains electricity generator.
If more than one operator is expected to set up or use a RITE-POWER generator at different times,
each operator is required to follow all safety rules and instructions in the operator’s manual. That
means every new operator should perform a pre-operation inspection and function tests before
using the unit.
5a) PRE-OPERATION INSPECTION
Always perform a pre-operation inspection.
The Pre-operation inspection is a visual inspection performed by the operator prior to each use of
the RITE-POWER generator. This inspection is designed to discover if anything is obviously wrong
with a unit prior to use.
A damaged or modified RITE-POWER generator must never be used. If any damage is discovered
the RITE-POWER generator must be removed from service until it has been repaired and
appropriate clear labelling added to warn and prevent its use.
Maintenance and repairs can be executed only by authorised personnel. If any person maintaining
or repairing the device is in any doubt, they should contact their supplying dealer or Ritelite
(Systems) Ltd.
Check the following parts or areas for any signs of damage or missing parts.
• Cables (for kinks, frays, abrasions, bare conductors showing)
• Plugs and Sockets for physical damage
• Catches and locking mechanisms.
• Make sure the case is free from cracks or areas of damage where water could enter
• Make sure all labels and warnings are present and readable on the product as detailed on the
following pages.

15
RITE-POWER 3850
RITE-POWER 1750
RITE-POWER 1750x2
OUTPUT
230V AC 50Hz
Max continuous output 2500W
RITELITE (SYSTEMS) LTD
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS 715mm (L) x 370mm (W) x 470mm (H) WEIGHT 52Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODES LK1770BP3850/2400/230/T60309
MAX CONTINUOUS OUTPUT POWER 2500W
IP RATING IP44
RITE-POWER 3850 PORTABLE BATTERY POWERED GENERATOR
A-262o2
Made in the UK
Product contains a lithium battery which must be disposed of correctly
RITELITE (SYSTEMS) LTD
CHARGER INPUT
230V AC 50Hz
OUTPUT
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS WEIGHT
Made in the UK
22Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODE SLK1770BP
MAX CONTINUOUS OUTPUT POWER 750W
IP RATING IP65
RITE-POWER 1750 PORTABLE BATTERY POWERED GENERATOR
565mm (L) x 360mm (W) x 235mm (H)
(EXCLUDING SOCKETS)
USE APPROVED RITELITE SLK350CH, SLK750CH OR SLK1000CH CHARGER ONLY (29.4V DC MAX)
WARNING: Hazardous voltage, potential shock hazard. No user servicable parts inside. Contact manufacturer for service or repair. Do not use / place in direct sunlight.
A-261E2
Product contains a lithium battery which must be disposed of correctly
RITELITE (SYSTEMS) LTD
RITE-POWER 1750x2 PORTABLE BATTERY POWERED GENERATOR
MANUFACTURE DATE
DIMENSIONS WEIGHT 36Kg
SERIAL NUMBER
OUTPUT VOLTAGE1 10V AC 60Hz
PRODUCT CODE SLK1770BP2/750/110/T60309
MAX CONTINUOUS OUTPUT POWER 750W
IP RATING IP65
OUTPUT
110V AC 60Hz
Max continuous output 750W
CHARGER INPUT
INSTRUCTIONS
CHECK VOLTAGE OF LOAD IS COMPATIBLE
WITH INVERTER OUTPUT
1. Connect load to output not exceeding 750W (subject to
load type).
2. Press green button to activate inverter - a continuous red
LED will illuminate to show mains power is on.
3. Display will show:
¥ Battery state of charge in percentage
¥ Estimat ed run time based on load
¥ Estimat ed recharge time to full based on progress
of charging.
Note: Display lights up to show when power is being drawn.
Display light blinks when charging.
4. Red LED flashes on switch to indicate battery low or fault
condition - turn off then on to reset after fault removed -
see manual for further information.
Note: Unit shuts down after 12 hours if no load or a load less
than 30W is detected. Press switch off then back on to reset.
WARNING: Hazardous voltage, potential shock hazard. No
user servicable parts inside. Contact manufacturer for
service or repair. Do not use / place in direct sunlight.
580mm (L) x 400mm (W) x 340mm (H)
(EXCLUDING SOCKETS)
USE APPROVED RITELITE SLK350CH, SLK750CH
OR SLK1000CH CHARGER ONLY (29.4V DC MAX)
ON/OFF
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk A-261F1
Made in the UK
Product contains a lithium battery which must be disposed of correctly

16
Note All labels shown above and on page 15 show one voltage only. Labels will differ between 110V and
240V units. Units with built-in chargers will have slightly different labels to include extra weight and different
basic instructions for use.
RITE-POWER 7700
RITE-POWER 8000
RITE-POWER 5250
A-262u
ON/OFF
CHECK VOLTAGE OF LOAD IS COMPATIBLE WITH INVERTER OUTPUT
1. Connect load to output not exceeding 2500W (2.5KW, subject to load type).
2. Press green button to activate inverter - a continuous red LED will illuminate to show mains power is on.
3. Display will show:
¥ Battery state of charge in percentage
¥ Estimated run time based on load
¥ Estimated recharge time to full based on progress of charging.
Note: Display lights up to show when power is being drawn. Display light blinks when charging.
4. Red LED flashes on switch to indicate battery low or fault condition - turn off then on to reset after fault
removed - see manual for further information.
PRODUCT INFO
OUTPUT
230V AC 50Hz
Max continuous output 2500W
RITELITE (SYSTEMS) LTD
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS 680mm (L) x 340mm (W) x 680mm (H)
(EXCLUDING SOCKETS) WEIGHT 57Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODES LK1770BP3
MAX CONTINUOUS OUTPUT POWER 2500W
IP RATING IP44
RITE-POWER 5250 PORTABLE BATTERY POWERED GENERATOR
A-262E3
Made in the UK
Product contains a lithium battery which must be disposed of correctly
OUTPUT
230V AC 50Hz
Max continuous output 2500W
RITELITE (SYSTEMS) LTD
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS 715mm (L) x 370mm (W) x 680mm (H) WEIGHT 91Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODES LK1770BP7700/2400/230/T60309
MAX CONTINUOUS OUTPUT POWER 2500W
IP RATING IP44
RITE-POWER 7700 PORTABLE BATTERY POWERED GENERATOR
A-262n2
Made in the UK
Product contains a lithium battery which must be disposed of correctly
OUTPUT
230V AC 50Hz
Max continuous output 4000W
RITELITE (SYSTEMS) LTD
MANUFACTURE DATE
Ritelite (Systems) Ltd, Meadow Park, Bourne Road, Essendine, Stamford, Lincolnshire, PE9 4LT, England
Tel. [phone] | E-mail. [email protected] | Web. www.ritelite.co.uk
DIMENSIONS 740mm (L) x 390mm (W) x 750mm (H) WEIGHT
Made in the UK
96Kg
SERIAL NUMBER
OUTPUT VOLTAGE 230V AC 50HZ
PRODUCT CODE RP8000PPS/230V
MAX CONTINUOUS OUTPUT POWER 4000W
IP RATING IP44
RITE-POWER 8000 PORTABLE BATTERY POWERED GENERATOR
Product contains a lithium battery which must be disposed of correctly
A-262V2

17
5b) USING THE RITE-POWER GENERATOR
1. Check there is sufficient battery capacity for the
task in hand, this is indicated by the display on the
front of the unit showing the battery capacity in a
percentage, where 100% is full capacity.
3. Make sure the RITE-POWER generator is
switched off via the button next to the display. The
display will automatically light up when the unit is
switched on and go dark when the unit is switched
off to conserve power when not in use.
4. Make connections to the mains output socket of
the RITE-POWER generator. Making sure the output
voltage of the RITE-POWER generator is within the
constraints of the equipment to be powered
from it.
2. If necessary, recharge the RITE-POWER
generator. As a point of note it is good practice to
always recharge the unit to full aer every use.
Chose a suitable location, heeding the warnings in sections 4 & 5 of this manual.

18
5. Check the device to be powered is within the maximum constraints of the RITE-POWER generator, see
technical specifications contained within this manual and on the RITE-POWER generator. Heed the notes in
the section Applications and Restrictions of use with regard to Inductive, Resistive and capacitive loads and
their limitations.
6. Once everything is connected press the power on
button. The display will light up and a red LED should
light in the middle of the switch to indicate that mains
power is on and everything is ok.
7. Note the estimated run time on the display, this will
vary according to the load driven by the RITE-POWER
generator. In the example here the display indicates 3
hours, 54 minutes remaining at the current
power drawn.
SYSTEM ENERGY MONITOR KEY
1. State of charge
2. Battery voltage (V)
3. Current draw (A)
4. Wattage (W)
5. Estimated run / recharge time
6. Battery capacity (Ah)
6
5
4
3
2
1
The display also shows various other parameters such as wattage, this can be a useful gauge to understand
what different powers are consumed by different equipment and the runtime that might be expected.
Note Display pictured above may vary in size depending on model.
Note Some models are fitted with a battery isolator switch. Turn off when not in
use to prevent unnecessary battery discharge. Turn on for operation, Isolator can
be switched off if only recharging is required. Isolator knob can be removed to
prevent unauthorised operation.

19
8. Certain equipment such as some lighting can be
dimmed, this can be useful to extend the runtime
required while still potentially providing enough
light for the task in hand.
9. In use note the fall of the battery capacity so
power isn’t suddenly lost unexpectedly. Once the
RITE-POWER generator gets towards the end of the
available capacity a beeping will be heard from the
unit and the red LED in the middle of the switch will
flash to denote the low power level, depending on
the size of the load being drawn will dictate how
soon until the load is then switched off.
10. Once the load has been switched off from the
depleted power pack the switch should be pressed
to switch the system off and the pack placed on
charge as soon as possible.
Note – If the battery is le to run completely
empty aer the low battery warning has
been indicating so for a while, the battery will
completely shut down and the display turn
completely off to preserve it’s lifetime. Please
ensure it is then recharged within 12 hours.
See note under charging.

20
5c) RECHARGING THE RITE-POWER GENERATOR
The RITE-POWER generator should be placed on charge to return it to full capacity once used. Choose
a suitable location to recharge the unit away from any aforementioned hazards. Ideally the RITE-POWER
generator should be charged in a cool ventilated environment.
Note – It is good practice to always keep the RITE-POWER generator fully charged up so it is always ready
for use.
Follow the steps below to recharge your RITE-POWER unit if it is fitted with a white charger input
connector.
Some units are fitted with an in-built charger, if this is the case the unit will not have a white input
connector, but will have either a yellow or blue connector. To charge these units simply connect the
supplied mains power cable (110V yellow or 240V blue) and the unit will begin to charge.
CHARGING UNITS WITH WHITE CHARGER INPUT CONNECTOR
2. Plug the charger into a suitable mains supply and
switch the power on.
Note – charger connections to the RITE-POWER
generator should always be done with the mains
power off to the charger, once connected the mains
supply to the charger can then be switched on.
1. Plug in either the SLK350CH, SLK750CH
or SLK1000CH charger into the RITE-POWER
Generator via the white 32A industrial connector,
turn the plug locking ring to secure the plug to the
socket and aid a secure connection.