RITFIT PPC03A Use and care manual

POWER CAGE
PPC03A
WITH CABLECROSSOVER
OWNER’S MANUAL & ASSEMBLY INSTRUCTIONS

13. If you have any question, please e-mail our custom-
er service team at [email protected].
IMPORTANT: READ ALL PRECAUTIONS CAREFULLY BEFORE USING THIS PRODUCT.
RETAIN OWNER'S MANUAL FOR FUTURE REFERENCE.
CARE AND MAINTENANCE
·
·
·
·
- Inspect and tighten all parts before using the equipment.
- Examine the equipment regularly for signs of damages or wear.
- Failure to examine regularly may affect the safety level of the equipment.
SAFETY & PRECAUTIONS
1
1. Keep childern and pets away from this equip-
ment.
2. Always inspect equipmenr prior to assure the
structual integrity. Some parts may need occa-
sional maintenance due to wear and tear.
3. Lubricate moving parts as needed (depends on use
but once a month is a good rule to follow).
In the event should you find this product has
either a defective or a missing part, do not use
substitute parts or try to use the unit in an
incomplete form. Please contact RITFIT for a
replacement.
Additional features on products may be added
during seasonal production but may not be
featured in line art diagrams at time of
production. Changes of such will not affect the
performance or assembly of the unit. If you
would like further clarification during your
assembly process please feel free to contact
RITFIT for direction.
This product has been designed for light
commercial or home use only. Light commer-
cial can be defined as a location with multiple
users but not in a membership setting. Exam-
ples would be hotels, fire departments, high
schools, etc. Commercial use would include,
but not limited to, locations that accept mem-
bership for use of equipment.
This exercise equipment was designed and
built for optimum safety. However certain
operator precautions apply whenever you
operate a piece of exercise equipment. Please
note the following safety procedures:
- Replace any defective components immediately and/or keep the equipment out of use
until repair.
- The equipment can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. One person at a time should use this equipment
unless otherwise designed for safety (example:
spotter stand on some weight benches).
6. Always use this equipment on a level surface. Do
not use outdoors or near water.
7. Keep hands and feet away from any moving parts
that are not intended to have body parts near them
while in use.
8. Do not insert any object into any openings unless
object is supposed to be inserted into a particular
place (such as a pin in a weight stack).
9. Before using this equipment, always do stretching
exercise to warm up.
10. Use this equipment only for its intended use as
described in manual.
11. Always wear appropriate workout clothing and
shoes when exercising. DO NOT WEAR ROBES
OR OTHER CLOTHING THAT COULD BECOME
CAUGHT IN THE EQUIPMENT.
12. BEFORE BEGINNING ANY EXERCISE PRO-
GRAM, CONSULT YOUR PHISICIAN.
5. If dizziness, nausea, chest pains, or any other
abnormal symptoms are experienced while using
this equipment, stop the workout at once. CONULT
A PHYSICIAN IMMEDIATELY.

Power Cage Warranty
Basic Warranty.
B. Who Is Covered?
You are covered by the Basic Warranty if you are a purchaser for use of the
RitFit Power Cage.
C. What’s covered?
The Basic Warranty covers the cost of all parts and labor needed to repair any item
on your power cage when it left the manufacturing plant that is defective in material,
workmanship or factory preparation. These warranty repairs or adjustments will be
made by RitFit at no charge, using new or remanufactured parts.
D. When It Begins?
The Basic Warranty begins on the day of order.
E. When It Ends?
The Basic Warranty lasts for 36 months from the date it begins, but the following
items are covered only for 12 months: bolts, nuts, washers, foot covers, J-hooks
and plate storage pegs.
F. What’s Not Covered?
Please note that while the standard Basic Warranty appliesto defects in material
and/or workmanship, it does not cover the power cage’s matte finish appearance.
Maintaining the matte finish appearance is solely the responsbility of the owner.
Basic Warranty doesn’t cover damage caused by environmental factors such as
airborne fallout, insect damage, chemicals, salt, and ocean spray. Nor do your
warranty cover damage caused by hailstorms, windstorms, tornadoes, sandstorms,
lightning, floods, and earthquakes. Your warranty does not cover conditions resulting
from anything impacting the power cage.
G. How To Contact Us?
To ensure you receive the best technical support, please visit our website:
www.rifitsports.comand register your warranty. Customers with registered
warranties are given a profile that allows for easier support and for us to contact
you with important product notifications. If any parts are missing, worn, damaged
or broken before the assembly, or you ever need to replace the parts, please contact
us at [email protected].
2
WARRANTY
A. What’s Covered Under RitFit LLC’s Basic Warranty?

Pull-Up Bar
Safety Bar
Low Row Foot Tube
J-Hook
Cable Handle
Quick Release Plates
Storage Tube
Plate Storage Rack
Landmine
Left Side
Right Side
Back
Front
BEFORE YOU BEGIN
3
Thank you for selecting the versatile RitFit®Power Cage. RitFit®Power Cage is designed
and manufactured to optimize users’ workout performance and minimize adjustment or
set-up time for users.
For your benefit, read this manual carefully before using the Power cage.If you have
additional questions, please call our Customer Service Department at [phone],
9:00 am - 5:00 pm PST (Mon.-Fri.). To help us assist you, please note the product model
number and serial number before calling. The model number isPPC03A.
BEFORE READING FURTHER, PLEASE REVIEW THE DRAWING BELOW AND
FAMILIARIZE YOURSELF WITH THE PARTS THAT ARE LABELED.

FASTENER AND TOOLS
a
b
c
d
e
M10x70 Square Neck Bolt
28x
a
M10x70 Square Neck Bolt
M10x70 Hex Bolt
M10x50 Hex Bolt
M10x25 Hex Bolt
M8x45 Hex Bolt
28
6
7
2
2
NO. DESCRIPTION QUANTITY
fM10 Nut
M8 Nut
43
2
cM10x50 Hex Bolt
7x
bM10x70 Hex Bolt
6x
eM10x25 Hex Bolt
2x
g
M10 Washer 58
h
M8 Expansion Bolt
Hex Key
4
i
1
j
Open-ended Wrench 2
k
Open-ended Wrench
2x
k
fM10 Nut
43x
iM8 Expansion Bolt
4 x
M10 Washer
58x
h
Hex Key
1x
j
dM8x45 Hex Bolt
2x
M8 Nut
2x
g
4
PARTS LIST

ACCESSORIES
A
B
C
D
J-Hooks Set
Quick Release Plates Storage Tubes Set
Safety Bars Set
Low Row Foot Tube
1
2
1
1
1
2
Left Upright Frame (front)
Right Upright Frame (front)
1
1
AJ-Hooks Set
1x
NO. DESCRIPTION QUANTITY
NO. DESCRIPTION QUANTITY
3
4
5
6
7
8
9
10
11
Upright Frame (back)
Bottom Base Frame
Upper Cross Frame
Rear Cross Beam
Bottom Cross Beam
Chrome Pull-Up Bar
2
2
1
1
1
1
2
4
Plate Holder Frame
Band Peg
Landmine
12
13 4
6Bolt Plates
Bolt-down Floor Bracket
MAIN FRAME
CSafety Bars Set
1x
DLow Row Foot Tube
1x
BQuick Release Plates
Storage Tubes Set
2x
2
Left Upright Frame (front)
1x
1
Right Upright Frame (front)
1x
2
PARTS LIST
5

PARTS LIST
678
9
Bolt Plates
6x
12 Bolt-down Floor Bracket
4x
13
Rear Cross Beam
1x
Bottom Cross Beam
1x
Plate Holder Frame
2x
Chrome Pull-Up Bar
1x
Band Peg
4x
10 Landmine
1x
11
5Upper Cross Frame
2x
4Bottom Base Frame
2x
3Upright Frame (back)
2x
6

Lat Pull Shaft
2x
PULLEY SYSTEM
14
15
16
17
18
19
20
Rubber Pad
Carabiner
Pulley
2
4
13
12
Pulley Peg
Plate Carriage1
2
14 Rubber Pad
2x
15 Carabiner
4x
Pulley Handle
2x
18 Plate Carriage
1x
21
22
23
24
Pulley Block
Low Row Bar
Pulley Handle
Lat Pull Shaft
1
2
2
1
Cable A
1
Cable B
19 Pulley Block
2x
23
22
24
NO. DESCRIPTION QUANTITY
21
Pulley Peg
12x
16 Pulley
13x
20 Low Row Bar
1x
17
Cable A
1x
Cable B
2x
7
PARTS LIST

2
STEP 1
4
Bottom Cross Beam
Bottom Base Frame
Bolt Plates
M10x70 Square Neck Bolt
M10 Washer
1
2
4
4
7
12
a
h
fM10 Nut
4
NO. DESCRIPTION QUANTITY
4
12
a
h7
f
2x
ASSEMBLY
8

ASSEMBLY
M10x70 Square Neck Bolt
2
STEP 2
9Plate Holder Frame
4
a
f M10 Nut 4
h M10 Washer 4
NO. DESCRIPTION QUANTITY
a
h
f
9
2x
9

4x
1
STEP 3
1
Right Upright Frame (front)
Left Upright Frame (front)
Upright Frame (back)
1
2
2
3
Bolt-down Floor Bracket 4
13
M10x70 Square Neck Bolt 8
a
f
h
M10 Nut
M10 Washer
8
8
NO. DESCRIPTION QUANTITY
3
a
h
f
1
2
knob
13
(Two People Are Required.)
*Please note the knob is facing toward each other!
ASSEMBLY
10

2
STEP 4
14
Plate Carriage
Guide Rod
1
2
18
22
NO. DESCRIPTION QUANTITY
(Two People Are Required.)
22
18
14
Rubber Pad
ASSEMBLY
11

1
STEP 5
6Rear Cross Beam
1
5Upper Cross Frame
Bolt Plates
M10x70 Square Neck Bolt
M8x45 Hex Bolt
2
4
2
12
a
d
M10 Nut
M8 Nut
4
f
g2
M10 Washer
h4
6 5
NO. DESCRIPTION QUANTITY
(Two People Are Required.)
Step 1
a
a
12
12
h
h
f
f
Step 2
d
g
Step 3
ASSEMBLY
12

1
STEP 6
5Upper Cross Frame
Bolt Plates
M10x70 Square Neck Bolt
2
4
4
12
a
fM10 Nut
4
hM10 Washer
5
NO. DESCRIPTION QUANTITY
(Two People Are Required.)
12
12
a
a
f
f
h
h
Step 1
Step 2
ASSEMBLY
13

STEP 7
Chrome Pull-Up Bar
M10x70 Square Neck Bolt
1
4
4
8
a
fM10 Nut
4
hM10 Washer
a
8
h
f
NO.
DESCRIPTION QUANTITY
(Two People Are Required.)
2x
ASSEMBLY
14

13
STEP 8
16 Pulley
Pulley Peg 12
17
M10x70 Hex Bolt 6 b
M10x50 Hex Bolt 7
c
M10 Nut 13
f
M10 Washer 26
h
NO. DESCRIPTION QUANTITY
c
h
16
f
x7
f
17
h
16
b
x6
ASSEMBLY
15

4
STEP 9
15 Carabiner
Pulley Handle
2
19
NO.
1
23 Cable A
Cable B 2
24
Pulley Block
2
21
2
fM10 Nut
M10 Washer 4 h
M10x25 Hex Bolt 2
e
DESCRIPT ION QUANTITY
start
end
*Disassemble only one side of Cable A first, then follow the step above to run through the power cage.
If this part is too tight,
adjust it by the bolt as
the diagram shows.
x2
x2
e
21
15
h
24
24
15
23
19
f
ASSEMBLY
16

4
STEP 10
10
Landmine
Band Peg
1
11
NO. DESCRIPTION QUANTITY
11
10
10
ASSEMBLY
17

1
STEP 11
AJ-Hooks Set
Quick Release Plates Storage TubesSet
Safety Bars Set
2
1
B
C
Low Row Foot Tube 1
D
NO. DESCRIPTION QUANTITY
ASSEMBLY
18
A
B
C
D
90°
90°
90°
90°
90°
90°