Riva RC5510 User manual

1
www.rivatech.de
RC5510
Installation Guide

2
www.rivatech.de
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
!
!

3
www.rivatech.de
Table of Contents
1. FEATURES ................................................................................4
2. PACKAGE CONTENTS .................................................................5
3. PART NAMES............................................................................6
4. INSTALLATION...........................................................................8
4.1. Installation Template ......................................................................9
4.2.Setting the Image Attribute ..............................................................9
4.3.Operating the OSD Menu .................................................................9
5. CONNECTIONS.........................................................................10
5.1.Connectors..................................................................................10
6. CONFIGURATION ......................................................................13
6.1.Set up network environment ...........................................................13
6.2. View video on web page ................................................................13
6.2.1. View video using IPAdmin Tool..................................................13
6.2.2. View video using IP address .....................................................15
6.3. Reset ........................................................................................15
6.4. Factory Default............................................................................15
APPENDIX (A): SPECIFICATIONS......................................................16
Summary ..........................................................................................16
Electrical Characteristics......................................................................17
Environment Condition .........................................................................17
APPENDIX (B): DIMENSIONS ..........................................................18
APPENDIX (C): HEXADECIMAL-DECIMAL CONVERSION TABLE .............19
REVISION HISTORY .......................................................................20

4
www.rivatech.de
1.FEATURES
Camera
Indoor/Outdoor Mini PTZ Dome IP Camera (Vandal Proof)
Sony 1/4” Super HAD CCD, 410K Pixel
x12 Optical Zoom, x16 Digital Zoom (Max x192)
True Day & Night (IR Cut Filter, DSS)
360° endless rotation
Intelligent pan/tilt controlling
Improvement of color rolling suppression
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MPEG4/MJPEG, 25/30FPS@D1(PAL/NTSC)
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video out for external monitors
Video Motion Detection supported
Two-way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
RS-485 supported
Micro SD card socket for external storage
OSD supported
VCA (Video Content Analysis)
VCA Presence and VCA Follow (Included as basic)
Optional possibility to upgrade VCA features via extension licenses.

5
www.rivatech.de
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
DC power adaptor
Terminal block
Installation Template
Power adaptor jack
Screws and Anchor blocks
Video BNC cable
Hex wrench driver
Quick Installation Guide
The above contents are subject to change without prior notice.
Note
i

6
www.rivatech.de
3. PART NAMES
①
②
③
④
⑤
* Models herein and their
appearance are subject to change
without any prior notice.
In Out
AUDIO DI DO RS-485
12VVout
In Out
AUDIO DI DO RS-485
12V
Vout

7
www.rivatech.de
1Micro SD Card Socket
It is a memory card slot for external storage.
2LAN Connector (Ethernet)
This is a RJ45 LAN connector for 10/100 Base-T Ethernet.
This LED lights up as orange and turns green when the encoder is powered on.
LED operation setting:
For the factory default setting, LED 2 blinks for the heartbeat and LED 1 turns on for
video signal. To change its setting, refer to the section 4.5.12. LED Setting of the
RIVA Web Interface Manual.
38 pin terminal block for audio, DI, and DO
Refer to the section “5.1.Connectors”for more specific information.
46 pin connector for analog video output, RS485, and power
Refer to the section “5.1.Connectors”for more specific information.
5Reset
Reset switch is used for restarting the camera or resetting it to Factory Default (FD).
Refer to the section “6.3. Reset”for more specific information.
LED1 LED2

8
www.rivatech.de
4.INSTALLATION
When assembling the main body of the camera and its dome
cover, make sure they fit each other into place.
Note
i
1) Connect the LAN cable, power
supply cable, and the video loop out
cable with the camera.
2) Place the installation template on
the ceiling.
3) Drill four holes on the template and
insert anchor blocks into the holes.
Fasten the surface mount bracket
with screws.
4) Put the main body on the surface
mount bracket of the camera. Make
sure the bracket and the main body fit
each other into place.
5) Fasten the main body with screws.

9
www.rivatech.de
The camera may fall off the ceiling even after the proper installation
and mounting. To prevent any accident, make sure the ceiling is
firm and stable enough to support the camera. If any reinforcement
is needed, consult with your safety personnel and proceed with the
installation.
4.1. Installation Template
4.2.Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video-in >
Attribute Setting. Brightness, contrast, hue, saturation and sharpness can be
adjusted.
4.3.Operating the OSD Menu
To operate the OSD of camera, refer to the ”OSD Menu Control Manual.”
Caution
!
Installation template
5510 V1.0

10
www.rivatech.de
5. CONNECTIONS
5.1.Connectors
1. Audio Input/Output Connection
Connect to the audio input device such as a mike and the audio output device such as
the amplifier speaker.
Audio Input
Audio Output
COM
Amplifier Speaker
MIC
②
③
④
⑤
In Out
AUDIO DI DO RS-485
12VVout
In Out
AUDIO DI DO RS-485
12V
Vout
⑥
①