Rivers Edge LANDMARK LM601 User manual

GAS/OIL
RATIO
50:1
Get parts online at
www.HuntRiversEdge.com
Operator's Manual
LM601
Landmark™
Permanent Blind
P/N: 26742
REV2: 02/06/18
© 2018 RETI
All Rights Reserved
Assembly Time
2-4 Hours

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-52
Operator's Manual
Landmark™Permanent Blind
CONTENTS
Introduction/Warnings..................................................................................................................................................................................................................2
Frame Assembly Instructions............................................................................................................................................................................................... 3-15
Skin Assembly Instructions.................................................................................................................................................................................................16-21
Ground Stake Instructions ........................................................................................................................................................................................................ 22
Warranty .......................................................................................................................................................................................................................................... 23
Parts Breakdown.....................................................................................................................................................................................................................24-25
Notes Pages..............................................................................................................................................................................................................................26-27
INTRODUCTION
Landmark™ Permanent Blinds are engineered with you the hunter in mind. We appreciate your purchase of one of our
world class products. Follow these few simple instructions and your blind will provide you many years of trouble-free
pleasure. Instructions should be kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product, DO NOT return to the retailer, contact the RETI customer
service department at 800-450-3343 for assistance.
WARNING
Read, Understand and Follow all assembly, inspection
and use instructions provided before each use. Failure to
follow warnings and instructions could result in serious
injury or death.
This product is for hunting purposes only! It is not to be
used as a camping tent or for any other function.
Never allow children to play in this product without adult
supervision. To do so could cause serious injury or death.
Never allow the material to cover your face. This material
can cause suocation and death if it is placed over face.
WARNING
Only use approved RETI parts. Failure to do so may result
in serious injury or death!
WARNING
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC. This tent meets the ammability
requirements of CPAI-84. The fabric may burn if left in
continuous contact with any ame source.The application
of any foreign substance to the tent fabric may render the
ame-resistant properties ineective.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 3
Operator's Manual
Landmark™Permanent Blind
1. Open box, remove contents and organize all parts together according to their labels (four A1 parts together, four HUB1 parts
together, etc.). This step greatly helps the ease of assembly.
2. Locate the four HUB1 corners, four of the six A1 poles and four of the six B1 poles and lay them out according to FIGURE 1.
3. Slide each A1 pole into the corresponding B1 pole so that the snap button secures both pieces together. Do this with the four
sets of A1 and B1 poles. SEE FIGURE 1.
4. Slide the four assembled A1 and B1 poles into the four HUB1 corners so that the snap buttons secure the pieces together. You
should now have the bottom tier frame of the blind assembled. SEE FIGURE 1.
FIGURE 1
FRAME ASSEMBLY INSTRUCTIONS
Tools needed – two 10mm wrenches
IMPORTANT ASSEMBLY TIP:
Do not tighten any nut and bolt combinations completely until all parts are assembled together! Finger tighten plus one turn of a
wrench only! This will temporarily hold the lock nut on the bolt while helping alignment of all parts! After all parts are assembled
together, all nut & bolt combinations must be completely tightened.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-54
Operator's Manual
Landmark™Permanent Blind
5. Slide the four C1 poles into the HUB1 corners so that the snap buttons secure pieces together. SEE FIGURE 2.
6. Attach the four HUB2 corners to C1 poles so that the snap buttons secure pieces together. PAY ATTENTION TO ORIENTATION OF
THE HUB2 CORNERS! SEE FIGURE 2.
FIGURE 2

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 5
Operator's Manual
Landmark™Permanent Blind
7. Slide each of the three D2 poles into an E2 pole so that the snap button secures both pieces together. SEE FIGURE 3.
8. Slide the three assembled D2 and E2 poles into the HUB2 corners. These do not attach with snap buttons and will be secured
together with hardware in a later step. SEE FIGURE 3.
FIGURE 3

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-56
Operator's Manual
Landmark™Permanent Blind
9. Attach each of the eight F1 poles to the bottom and middle tiers of the blind frame using two M6 x 35mm bolts (20) and M6
nuts (22). Make sure upper bolts are securing the D2 and E2 poles along with the F1 poles. SEE FIGURE 4.
NOTE: PAY ATTENTION TO THE ORIENTATION OF THE BOLTS! THE HEAD OF THE BOLT MUST BE ON THE OUTSIDE OF THE FRAME. THIS
HELPS PREVENT UNNECESSARY WEAR ON THE SKIN WHEN FULLY ASSEMBLED.
FIGURE 4
20
22
20
22

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 7
Operator's Manual
Landmark™Permanent Blind
10. Slide two G1 poles into HUB2 corners on the door side of the blind so that the snap buttons secure pieces together. It is critical that the
G1 poles are oriented such that snap buttons are facing each other and each through hole is located closer to the HUB3 corners than
the HUB2 corners. SEE FIGURE 5.
11. Attach two HUB3 corners to the two G1 poles so that the snap buttons secure pieces together. PAY ATTENTION TO THE
ORIENTATION OF HUB3! SEE FIGURE 5.
FIGURE 5
Through Hole
Closer to HUB3
than HUB2
Through Hole
Closer to HUB3
than HUB2

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-58
Operator's Manual
Landmark™Permanent Blind
12. Slide remaining two G1 poles into the other HUB2 corners so that snap button secures pieces together. It is critical that the G1 poles
are oriented such that snap buttons are facing each other and each through hole is located closer to the HUB3 corners than the
HUB2 corners. SEE FIGURE 6.
13. Attach remaining two HUB3 corners to the two G1 poles so that snap buttons secure pieces together. PAY ATTENTION TO THE
ORIENTATION OF HUB3! SEE FIGURE 6.
FIGURE 6
Through Hole
Closer to HUB3
than HUB2
Through Hole
Closer to HUB3
than HUB2

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 9
Operator's Manual
Landmark™Permanent Blind
14. Slide the two H1 poles into the two I1 poles so that snap buttons secure pieces together. SEE FIGURE 7.
15. Slide assembled H1 and I1 poles into HUB3 corners so that snap buttons secure pieces together. PAY ATTENTION TO THE
ORIENTATION OF THE TABS ON H1 AND I1 POLES SO THAT THEY POINT UPWARD. SEE FIGURE 7.
FIGURE 7

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-510
Operator's Manual
Landmark™Permanent Blind
16. Slide remaining two A1 poles into remaining two B1 poles so that snap buttons secure pieces together. SEE FIGURE 8.
17. Slide assembled A1 and B1 poles into HUB3 corner so that snap buttons secure pieces together. You should now have the top tier
frame of the blind assembled. SEE FIGURE 8.
FIGURE 8