Riverside Furniture Madison Panel King Bed User manual

Headboard Panel
1 pc. One Left &
One Right 1 pc.
Headboard Post Headboard Stretcher
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
1 pc.10 pcs. H-G 10 pcs. H-I
5mm
Allen Wrench
Ø5/16" x Ø18mm
Flat Washer
Ø5/16" x Ø14mm
Spring Washer
H-A H-B H-C
6 pcs.
H-D
Madison
Panel King Bed
Assembly Instructions
Ø5/16"-18 x 1-1/2"
Allen Head Bolt
H-F
4 pcs.
H-E
Ø5/16"-18 x 1-1/4"
Allen Head Bolt
8 pcs.
R-B 1 pc.
8 pcs.
Ø5/16"
Hexagonal Nut
12 mm Open
Wrench
Ø5/16"-18 x 82mm
Long All-thread Bolt
2 pcs.
R-A R-D
8 pcs.
R-C
Ø5/16"x14mm
Spring washer
R-E R-F
8 pcs.
1 pc.
5/0 Wood Slat
60-3/4" long
8 pcs. 8 pcs.
4 pcs.
F-A F-C F-D
F-B
76080 / 76180 -- 6/0-6/6 Panel Headboard
76081 / 76181 -- 6/0-6/6 Panel Footboard w/Slats
76072 / 76172 -- 5/0-6/6 Bed Rails
76082 / 76182 -- 6/0 Bed Rails
Ø5/16"x34x14x2mm
Lock Washer Black
2 pcs.
R-A
Page 1 of 5

Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Madison
Panel King Bed
Assembly Instructions
76080 / 76180 -- 6/0-6/6 Panel Headboard
Detail: B
Detail: A
H-E
H-I
H-D
H-G
H-F
H-I
H-G
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two
people are used to perform the following steps.
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of
the Headboard Panel, using the Flat Washers (H-G), Spring
Washers (H-F) and the Ø5/16" x 1-1/2" Bolts (H-D). Do not fully tighten until after next
step. (see Detail A).
3. Attach the Headboard Stretcher (H-C) to the Headboard Posts using the same Washers
and the Ø5/16" x 1-1/4" Bolts (H-E).
4. Tighten all Bolts using the Allen Wrench (H-I). (see Detail A and B).
5. Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.
Page 2 of 5

Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Madison
Panel Queen Bed
Assembly Instructions 76080 / 76180 -- 6/0-6/6 Panel Headboard
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING A
CALIFORNIA KING (6/0) METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING A KING SIZE (6/6)
METAL BED FRAME
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
Page 3 of 5

Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Madison
Panel King Bed
Assembly Instructions
6/6 King Standard Bed
76080 / 76180 -- 6/0-6/6 Panel Headboard
76081 / 76181-- 6/0-6/6 Panel Footboard w/Slats
76072 / 76172-- 5/0-6/6 Bed Rails
OR
6/0 California King Bed
76080 / 76180 -- 6/0-6/6 Panel Headboard
76081 / 76181 -- 6/0-6/6 Panel Footboard w/Slat
76082 / 76182 -- 6/0 California King Bed Rails
76080 / 76180 -- 6/0-6/6 Panel Headboard
76081 / 76181 -- 6/0-6/6 Panel Footboard w/Slats
76072 / 76172 -- 5/0-6/6 Bed Rails
76082 / 76182 -- 6/0 Bed Rails
ASSEMBLY STEPS :
1.Install the Ø5/16" x 82mm Long
All-Thread Bolts (R-F) to the threaded
inserts of the Headboard and Footboard
(see Detail C) .
R-F
R-F
Detail: C
Page 4 of 5

Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Madison
Panel King Bed
Assembly Instructions
ASSEMBLY STEPS :
2. Carefully position one end of one Bed Rail (R-A) onto the All-thread
Bolts installed on the Headboard and connect using the Half moon
washers (R-B), Spring washer (R-C) & Hex Nuts (R-D). Only partially
tighten the Nuts until the Footboard has been connected. Repeat for
other Bed Rail.
3. Position and connect the Footboard (F-A) to the other end of the Bed
Rails, attaching as in the previous Steps.
4. Carefully align the Footboard to be 'square' with the Headboard.
Using the Open Wrench (R-E) tighten all Hex Nuts attaching the Bed
Rails to the Headboard and Footboard. (See Detail D).
5. Attach the four Support Legs (F-C) to the bottom side of four Wood
Slats (F-B). (See Detail E).
6. Position and attach the Slats to the Bed Rails using the Wood Screws
(F-D) and your Phillips Screwdriver. (See Detail F).
The levelers located at the bottom of the Support Legs can be adjusted if
necessary to help support the Slats.
Bed rail Detail: D
Bed rail
Headboard
R-A
F-D
Detail: F
R-A
Footboard
Detail: E
F-C
F-B
8 pcs.
4 pcs.
leveling
R-B R-C
R-E
R-D
Page 5 of 5