Riverside Furniture Precision King Bed User manual

Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Page 1 of 6
PARTS LIST:
No. Description Quantity
Sketch
A
B
C
Panel 1
Post 1 - Left
1 - Right
Stretcher 1
Left Right
Flat Washer
4mm
5/16"
5/16"
1
'L'-Allen Key
8
8
Spring Washer
F
E
G
H
5/16" x 1-3/4" 4
Allen Head Bolt
D
SizeSketch
HARDWARE LIST:
No. Description Quantity
Allen Head Bolt 5/16" x 2-1/4" 4
Phillips Screwdriver
TOOLS REQUIRED (NOT PROVIDED)
4mm 1
Straight Allen
Key
H-2
21882 KG LOW UPH HDBD

A
E
H
B
C
B
Be sure to check all packing material carefully for small parts, which may have come loose inside the
carton during shipment. To prevent possible scratches or damage, this furniture should be assembled on a
soft surface such as a blanket or carpet.
ASSEMBLY STEPS:
1. Place the Headboard Panel (A) face down on the soft surface.
2. Attach the Left and Right Legs (B) to the back of the Headboard Panel using the Allen-Head Bolts (E),
Spring Washers (F) and Flat Washers (G). Do not fully tighten Bolts until after next step.
3. Attach the Stretcher (C) to the Legs as shown using the Bolts (D) and Washers as before.
4. Adjust parts for correct fit if necessary and tighten all Bolts using the Allen Key (H).
5. Carefully lean the assembled Headboard against the wall where the bed will be used.
Note: There are levelers installed in the bottom of the Posts which can be adjusted if needed, to align the
Headboard with the Nightstands.
Left
Right
21882 KG LOW UPH HDBD
Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Page 2 of 6

Footboard 1
I
Queen Roll Slat 1
J
Slat Support Rails 2
LSlat Support Leg
K
1
21885 KG STRG FTBD
PARTS LIST:
No. Description Quantity
Sketch
21876 QN/KG RAILS
Queen / Eastern
King Bed Rail 2
S
PARTS LIST:
No. Description Quantity Sketch
Curved Washer
12mm
32L x 13 x 8mm
5/16"
5/16" x 12MM
1
Open Wrench
8
8
Spring Washer
8
Hex Nut
V
U
W
Ø10*40 4
Wood Dowel Pin
X
Y
5/16" x 4-1/2" 8
All-Thread Bolt
T
SizeSketch
HARDWARE LIST:
No. Description Quantity
Flat Washer
4mm
5/16"
5/16"
5/16" x 1-1/4"
1
'L'-Allen
Key
4
4
Spring Washer
2
Allen Head Bolt
O
N
P
Ø8 X 1" 32
Wood Screw
Q
R
5/16" x 3" 2
Allen Head Bolt
M
SizeSketch
HARDWARE LIST:
No. Description Quantity
Phillips Screwdriver
TOOLS REQUIRED (NOT PROVIDED)
4mm 1
Straight Allen
Key
H-2
Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Page 3 of 6

M
O
P
Q
T
T
U
V
W
X
Y
I
K
K
L
R
Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Page 4 of 6

R
J
S
After the Bed is assembled, completely unroll the Bed Roll Slat (J) onto the Bed.
Using your Phillips Screwdriver, attach the Slats nearest the Headboard and Footboard and
attach the middle of the Slats to the Slat Support Rails in the middle of the Bed using the
1" Long Wood Screws (R).
Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Page 5 of 6

Precision
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
Use these holes for attaching the wood side rails.
All hardware is included with the side rails.
Use these holes for attaching a California
king size metal bed frame.
Use these holes for attaching a standard
King size metal bed frame.
Page 6 of 6