Riverside Furniture Queen 46170 User manual

Page 1 of 3
8 pcs.
email: [email protected]
FURNITURE
Riverside
6 pcs.
1 pc.
Hardware and Parts packed with the Queen Storage Footboard
F-A
F-E F-F
2 pcs.
∅5
16-18 x 2-3/4" Long
Allen Head Bolt
8 pcs.
#8 x 1" Wood
Screw
F-G
Queen Storage
Footboard
Hardware and Parts packed with the 5/0-6/6 Bed Rails
8 pcs. 8 pcs.
∅5
16-18 x 3-1/2" Long
All-Thread Bolt
8 pcs.
Queen / Eastern King
Bed Rail
2 pcs.
R-A R-B R-C R-D R-E
R-F 1 pc.
Ø5
16-18 Hex Nut
12mm Open Wrench
Slat Support Rails
Queen Roll Slat
(61" X 80-7/8")
1 pc.
F-B 2 pcs.
F-C 1 pc.
F-D
Slat Support Leg
Vogue Bed Room
Queen Bed
Assembly Instructions
∅5
16-18 x 1-1/2" Long
Allen Head Bolt
Ø5
16 x 12 x 3mm
Spring Washer
Ø5
16 x 19 x 2mm
Flat Washer
8 pcs.
F-I 8 pcs. 1 pc.
5mm Allen Wrench
F-J
Ø5
16 x 12 x 3mm
Spring Washer
46170
4/6-5/0 UPH HEADBOARD
46174
4/6-5/0 PANEL HEADBOARD
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
Part A
Part B
Be sure to check all packing material carefully for small parts, which may
have come loose inside the carton during shipment. To prevent possible
scratches or damage, this furniture should be assembled on a soft surface
such as a blanket or carpet.
To prevent possible damage to furniture and personal injury, it is
recommended that two people are used to assemble and set-up this bed.
Made in Viet Nam
Drawer Box
Support Leg
8-3/4" long with
leveler
F-H
F-K
M5/16" x 19*2mm
Flat Washer
2 pcs.
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
ASSEMBLY STEPS :
1. Place the Storage Footboard (F-A) face down on a clean and soft
surface.
2. Attach the Drawer Box Support Legs (F-E) using the Flat Washers
(F-I), Spring Washers (F-H) and 1-1/2" long Bolts (F-F). Tighten with
the Allen Wrench (F-K). See Detail A.
Detail: A
F-F F-K
F-H
F-I
F-A
F-E
1 pc.
4mm Allen Wrench
R-G
R-G
Note: For a Storage Bed, the Wood
Slat Support Cleat mounted on the
back side of the Bed Rails must be
mounted at the upper location. If
needed, using the Allen Wrench
(R-G) remove the Bolts and
Washers and remount it at the
upper position on the Bed Rails. It
is mounted at the lower position
for a Standard Bed.
The Filler Rail mounted at the top
edge of the California King Bed
Rails must also be temporarily
removed to assemble the Slats on
the Bed.
Slat Support Cleat

Page 2 of 3
email: [email protected]
FURNITURE
Riverside Vogue Bed Room
Queen Bed
Assembly Instructions
Adj Glide
STEP 8
3. Lean the back of the Headboard against the wall where the Bed will be
assembled.
4. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in
the Headboard Legs and into the metal inserts on the Footboard.
5. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on
the Headboard and connect using the Flat Washers (R-E), Spring Washers
(R-D), and Hex Nut (R-C). Only partially tighten the Nuts until the Footboard
has been connected. Repeat for other Bed Rail.
6. Position and connect the Footboard (F-A) to the other end of the Bed Rails,
attaching as in the previous Steps.
7. Carefully align the Footboard to be 'square' with the Headboard. Using the
Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the
Headboard and Footboard. (See Detail E).
F-C
F-C
F-C
F-D
F-D
8. Assemble Parts A & B of the Slat Support Rails (F-C) using the two 1-1/2" long
Bolts (F-F), Spring Washers (F-H) and Flat Washers (F-I). Assemble the Slat
Support Leg (F-D) to the Support Rails using the two 2-3/4" Long Bolts (F-G) and
the same Washers. Tighten all four Bolts with the Allen Wrench (F-K).
9. Position the Slat Support assembly into the pockets on the Headboard and
Footboard.
F-F
F-H
F-I
F-K
F-G
F-H
F-I
F-K
Note: Use these four holes
when assembling the Slat
Support Rails for a Queen or
Eastern King Bed.
Note: Use these four holes
when assembling the Slat
Support Rails for a California
King Bed.
75-1/8" For Queen / Eastern King
NOTE: The Slat Support Rails Parts
A & B, and Support Leg, can be
assembled to fit a Queen/King Bed or
to fit a California King Bed length,
depending on the sets of holes used.
Made in Viet Nam
R-F
R-C
R-E
R-B
R-D
R-A
R-A
46170
4/6-5/0 UPH HEADBOARD
46174
4/6-5/0 PANEL HEADBOARD
Detail E
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS

Page 3 of 3
email: [email protected]
FURNITURE
Riverside Vogue Bed Room
Queen Bed
Assembly Instructions
After the Bed is assembled, completely unroll the Bed Roll Slat (F-B) onto the
Bed.
Using your Phillips Screwdriver, attach the Slats nearest the Headboard and
Footboard and attach the middle of the Slats to the Slat Support Rails in the
middle of the Bed using the 1" Long Wood Screws (F-I).
STEP 2
R-A
F-J
Made in Viet Nam
46170
4/6-5/0 UPH HEADBOARD
46174
4/6-5/0 PANEL HEADBOARD
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
Note:
To prevent undue stress on any bed connection
joints, always remove the mattress and box springs
before moving to a different location in the room
and always use extreme care when moving.