RJX Hobby CAOS 330 User manual

CAOS 330
Assembly Manual V1.0

Assembly Manual of the RJX CAOS 330
For the correct assembly and safe flying of your
RJX CAOS 330 Model, this manual uses this symbol
where special attention is required. Failing to carry out the
instructions at this point in the assembly will result in an
electronic and/or mechanical failure or possible injury.
HOW TO USE THIS INSTRUCTION MANUAL
This manual contains the detailed instructions to build and set
up the RJX CAOS 330. Please follow it to ensure that you
achieve the best performance and mechanical integrity from
your finished kit.
For those of you who already have experience with model
helicopters, we strongly suggest that you assemble and
adjust your model according to these instructions for the
best results. Please keep this manual in a safe place and
refer to it when replacing spare parts or upgrading.
DISCLAIMER
While every effort has been made to supply the proper
information in this manual, the Manufacturer and Distributor
cannot guarantee that the consumer will interpret or follow
these instructions as intended and therefore the Manufacturer
and Distributor cannot assume any liability for damage or
claims occurring from the misuse of our product.
This product is intended for advanced users. It may look easy
when watching an experienced pilot flying his model, but it
takes dedication and numerous hours of practice to be able to
operate this model safely and efficiently.
Beginners are encouraged to seek help from an experienced
pilot to assist in the first test flights. We encourage you to
practice frequently and enjoy the experience of RC rotary
flight!
WARNING
LiPo batteries need special care. Improper storage, handling
or charging may cause fire or damage your Helicopter and
possibly to yourself. Contact your dealer or supplier for more
information.
1. Check your charger settings before charging your LiPo
battery to insure they are correct for the specifications
of the battery.
2. We recommend storing and charging LiPo batteries in
a Lipo sack or porcelain container. If kept in a metal
container or ammo case, the batteries may explode if
the storage containers are sealed and the gases are
not able to vent. We recommend using the original Lipo
Sack from the USA since it was designed to contain
the jet flames discharged from a failing Lipo battery.
3. Please keep LiPo Batteries away from sources of heat.
4. Never store LiPo Batteries fully charged.
5. NEVER SHORT CUT LiPo Battery wires.
6. Before connecting your LiPo battery to the Helicopter,
make sure your transmitter is turned ON and all sticks
and switches are set properly.
Page 2

TO PREVENT LOOSE SCREWS AND BOLTS
Regardless how tightly nuts, bolts and screws are tightened,
they slowly loosen over time due to vibration of the helicopter.
Should this happen, you will lose control of the helicopter
which may cause severe damages or very potential dangerous
situation.
We strongly recommend that you apply thread lock to any
nuts, bolts or screws. There are two types of thread lock, blue
(medium) and red (hard).
 Clean the nuts, bolts and screws with Alcohol (or
similar) before you apply the thread lock.
 Use blue thread lock on screws that have to be
removed regularly, and
 Red thread lock for screws that should be fixed
permanently.
1. Use CA: (Super glue or similar) at this point
2. LOCTIDE 243 (blue) - LOCTIDE 648 (red):
Remove oil and grease then apply shown thread lock.
(This applies throughout the manual)
3. GREASE: Remove oil and grease. (This applies
throughout the manual)
Items required to complete the RJX CAOS 330
- PCM or 2,4 Ghz Radio System
- CC3D or NAZE 32 Control Board
- 4x 1806-2207 Type 2000-2200 kV Brushless Out runner
Motor
- LiPo Pack 3S- 6S 1300 up to 2200 mAh (depending on
setup)
- 4x 10A-30A ESC (if not delivered)
- 5x3 – 6x4,5 CW/CCW or 3D Propeller
- LiPo Charger
Tools required (not included)
- Allen Drivers 1,5 mm - 2 mm - 2,5 mm - 3 mm - 4 mm
- Philips Drivers large - middle - small
- Nut Drivers 4,5 mm - 5,5 mm - 7 mm
- Cutter
- Universal Pliers
- Sandpaper
- Cyanoacrylate (CA - Superglue)
Page 3

Page 4
STEP 1

Page 5
STEP 2

Page 6
STEP 3
(Optional)

Page 7
STEP 4
(Optional)

Page 8
STEP 5