Robe Robin 1200 User manual

1
Version1.4

2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains ............................................................................................ 6
3.2 Installing the top hat ................................................................................................... 7
3.3 Installing the eggcrate ................................................................................................ 8
3.4 Rigging the xture ...................................................................................................... 9
3.5 DMX-512 connection................................................................................................ 11
3.6 Ethernet connection ................................................................................................. 12
4. Wireless DMX operation .............................................................................................. 14
5. Control menu map........................................................................................................ 15
6. Robin 1200 LEDWash - DMX chart.............................................................................. 18
6.1 Virtual colour wheel - colour mixing chart ............................................................... 22
7. Control menu ............................................................................................................... 27
7.1 Tab " Address" ......................................................................................................... 28
7.2 Tab "Information"...................................................................................................... 29
7.3 Tab "Personality"......................................................................................................30
7.4 Tab "Manual Control" ............................................................................................... 31
7.5 Tab "Stand-alone" ................................................................................................... 32
7.6 Tab "Service"............................................................................................................ 33
8. RDM ............................................................................................................................... 34
9. Error and information messages ................................................................................ 35
10. Technical Specications............................................................................................ 36
11. Maintenance and cleaning......................................................................................... 38
11.1 Replacing fuse ....................................................................................................... 39
12. ChangeLog ................................................................................................................. 39
13. Photometric diagrams................................................................................................ 40
Robin 1200 LEDWash

3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ROBIN 1200 LEDWASH !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
The Robin 1200 LEDWash was designed for indoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS
UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the xture.
This xture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the xture from AC power before cleaning, removing or installing the fuses, or any part.
The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords
as this canresult in re or electric shock.
Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power
cord from time to time.
Refer servicing to qualied service personnel.
This xture falls under protection class I. Therefore this xture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this xture to a dimmer pack.
LED light emission. Risk of eye injury. Do not look into the beam at a distance of less
than 1 meter from the front surface of the product. Do not view the light output with
optical instruments or any device that may conncentrate the beam
If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Do not shake the xture. Avoid brute force when installing or operating the xture.
This xture was designed for indoor use only, do not expose this unit to rain or use near water.

4
When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture
or dust.
Air vents and slots in the xture´s head and base are provided for ventilation, to ensure reliable operation of
the device and to protect it from overheating.
Do not block the LEDs array with any object when the xture is under operation.
The openings should never be covered with cloth or other materials, and never must be blocked.
This xture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly faste-
ned.
Always use a secondary safety cable when mounting this xture.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xtu-
re.
Do not block the front objective LEDs with any object when the xture is under operation.
The xture becomes very hot during operation. Allow the xture to cool approximately 20 minutes prior to
manipulate with it.
Operate the xture only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the xture. Most damages are the result of unprofessional operation!
Please use the original packaging if the xture is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, crash etc.

5
2. Fixture exterior view
Rear panel of the base
1- 5-pin DMX IN
2- 3-pin DMX IN
3 - Fuse holder
4 - Ethernet input
5 - 5-pin DMX OUT
6 - 3-pin DMX OUT
7 - Power cord
1 - Lens array
2 - Handle
3 - QVGA touch screen
4 - Control buttons
5- Base
6- Tilt lock
The head should be locked for transportation- the tilt lock latch (6) has to be in the locked positions. To unlock
the head, move this latch to unlock position before operating the xture.
The ENTER/DISPLAY ON button also serves for switching the display on when the xture is disconnected
from the mains.

6
3. Installation
Fixtures must be installed by a Qualied electrician in accordance with all
national and local electrical and construction codes and regulation.
3.1 Connection to the mains
For protection from electric shock, the xture must be earthed!
The Robin 1200 LEDWash is equipped with auto-switching power supply that automatically adjusts to any 50-
60Hz AC power source from 100-250 Volts.
Install a suitable plug on the power cord, note that the cores in the power cord are coloured according to the
following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualied electrician.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth

7
3.2 Installing the top hat
Switch off the xture before top hat installation
1. Go to the xture menu and set reduced tilt movement (Personality --> Pan/Tilt Setting-->
Tilt Movement Range --> reduced).
2.Unscrew the four fastening screws (3) which securing flange (4) to the head (5) and install new flange. Keep
its right position- the cutouts (A) in the flange must look towards the arms.
Original flange New flange
3.Place the top hat (1) on the head (5), press locks (2) and turn the top hat counter-clockwise until it snap into
slots (B) in the flange.

8
3.3 Installing the eggcrate
Switch off the xture before top hat installation
1. Unscrew the four fastening screws (1) which securing top ange (2) to the head (7) and remove both ange
and transparent plastic cover (3) from the head.
2. Unscrew the three fastening screws (4) which securing black eggcrate (5) to the zoom module (6) and
remove it.
3. Put the transparent eggcrate on the zoom module (6) and screw it with three screws (4) with washers to
the zoom module (6).
4. Place the transparent cover (3) and the top flange (2) back to the head and secure it with four screws (1).

9
3.4 Rigging the xture
The installation of the xture has to be built and constructed in a way that it can hold 10 times the weight for 1
hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
The xture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualications, do not attempt the installation yourself, but instead
use a professional structural rigger. Improper installation can result in bodily injury or damage to property.
The xture has to be installed out of the reach of people.
If the xture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The
xture must never be xed swinging freely in the room.
Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety of
a possible installation, do not install the moving head!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the xture’s
weight.
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use an appropriate clamp to rig the xture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is xed properly! Ensure that the
structure (truss) to which you are attaching the xtures is secure.
The xture can be placed directly on the stage oor or rigged in any orientation on a truss without altering its
operation characteristics .
For securing a xture to the truss install a safety wire that can hold at least 10 times the weight of the xture.
Use only safety wire with screw-on carabine. Pull the safety wire through the carrying handles and around the
truss as shown on the pictures below.
Note: If the safety wire is too long, whip it several times around the trusss in order to attach the xture tight.
In case of an accident, the way of the falling xture will be short.
.
.

10
Securing the xture via one safety wire Securing the xture via two safety wires
When installing xtures side-by-side,
avoid illuminating one xture with another!
1-Clamps
2-Safety wire
3-Omega holder
4-Quick-lock fastener
5-Carrying handles
6-Truss
.

11
3.5 DMX-512 connection
The xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the xture or one xture with another.
DMX - output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-out-
puts, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always
connect one output with the input of the next xture until all xtures are connected.
Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ωresistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last xture.
1- Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
1- Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected

12
3.6 Ethernet connection
The xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control soft-
ware running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identies any node (xture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin 300E Wash is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5
(with four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the xture to the network.
RJ-45 socket (front view): RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD- 6- RX-
3- RX+ 7- Not connected
4- Not connected 8- Not connected
Patch cables that connect xtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-1 2-2 3-3 4-4 5-5 6-6 7-7 8-8
If only the xture and the computer are to be interconnected,no hubs or other active components are needed.
A cross-cable has to be used:
1-3 2-6 3-1 4-8 5-7 6-2 7-5 8-4
If the xture is connected with active Ethernet socket (e.g. switch) the network icon will appear at the
bottom right corner of the screen:
Direct Ethernet operation
Connect the Ethernet inputs of all xtures with the Ethernet network.
Option “ Artnet (gMaI or gMA2)" has to be selected from “Ethernet Mode” menu on the xture.
Set IP address (002.xxx.xxx.xxx / 010.xxx.xxx.xxx) and the Universe.
(DMX address=92) (DMX address=46) (DMX address=1)
IP addres=002.168.002.004 IP addres=002.168.002.003 IP addres=002.168.002.002
Universe=1 Universe=1 Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Different from xture IP addresses)
NET mask: 255.0.0.0

13
Ethernet / DMX operation
Options “Art2DMX” has to be selected from the “Ethernet Mode” menu on the rst xture (connected to the
Ethernet) in the xture chain,next xtures have standard DMX setting.
Connect the Ethernet-input of the rst xture in the data chain with the network. Connect the DMX output of
this xture with the input of the next xture until all xtures are connected to the DMX chain.
Caution: At the last xture, the DMX chain has to be terminated with a terminator. Solder a 120 Ωresistor
between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last xture.
Example:
DMX address=1 DMX address=46 DMX address=92
IP addres=002.168.002.002
Universe=0
DMX address=1 DMX address=46 DMX address=92
IP addres=002.168.002.003
Universe=1

14
4. Wireless DMX operation
The Robin 1200 LEDWash is equipped with the Lumen Radio CRMX module and antenna for receiving DMX
signal. CRMX module operates on the 2.4 GHz band.
The item " Wireless " from the menu "DMX Input" allows you to activate receiving of wireless DMX (Personal-
ity--> DMX Input -->Wireless.). First two options from the "DMX Input" menu are stated in DMX chart as well
(channel Power/Special functions , range of 10-19 DMX). If DMX input option is changed by DMX command,
the change is permanently written into xture´s memory.
DMX range of 10-19 switching xture to the wired/wireless operation is active only during rst 10 sec-
onds after switching the xture on.
After switching the xture on, the xture checks both modes of receiving DMX in the following order:
1. For the rst ve seconds, the xture receives DMX signal from the wired input. If the Power/Special functions
channel is set at some DMX input option, the xture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is nished. If DMX input option is
not set, the xture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the xture receives wireless DMX signal and again detects if the Power/Special
functions channel is set at some DMX input option, if not, the xture will take option which is set in the xture
menu "DMX Input".
To link the xture with DMX transmitter.
The xture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Wireless State“ (Information
-->Wireless State).
To unlink the xture from DMX transmitter.
The xture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter“ (Information--> Wireless
State --> Unlink Wireless Adapter.).
Note: If the option "Wireless In/XLR Out" is selected (Personality--> DMX Input -->Wireless In/XLR Out), the
xture receives wireless DMX and sends the signal to its wired DMX output. The xture behaves as " Wire-
less/Wired" adapter.
Example of using

15
5. Control menu map
Default settings=Bold print
i
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Addressing Settings DMX Address 001-255
Ethernet Settings Ethernet Mode Disable
ArtNet
gMAI
gMA2
Art2DMX
IP Address/NetMask Default IP Address
Custom IP Address
Net Mask
ArtNet Universe 0-255
MANet settings MANet I/IIUniverse 1-256
MANet Session ID 1-32
Information Fixture Times Power On Time Total Hours
Resetable Hours
Air Filters Elapsed Time
Alert Period 10-300
Fixture Temperatures LEDs 1Temperature Current
Maximum NonRes.
Maximum Res.
LEDs 2Temperature Current
Maximum NonRes.
Maximum Res.
AmbientTemperature Current
Maximum NonRes.
Maximum Res.
Base Temperature Current
Maximum NonRes.
Maximum Res.
DMX Values Pan
:
Dimmer Fine
Wireless State* Signal Qualityr
Unlink Wireless
Adapter
Software Versions Display System
Module M
Module L
Product IDs Mac Address
RDM UID
RDM Label
View Logs Fixture Errors
Fixture Status Power On
Power Off
Fixture Position
Fixture Temperatures LEDs Temperature
Ambient Temperature
Base Temperature
Personality User Mode User A Settings
User B Settings
User C Settings
DMX Presets Mode 1

16
Mode 2
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Mode 3
Mode 4
Mode 5,
Mode 6
View Selected Preset
DMX Input Wired
Wireless
Wireless In/XLR Out
Pan/Tilt Settings Pan Reverse Off, On
Tilt Reverse Off, On
Pan/Tilt Feedback Off, On
Pan/Tilt mode Time
Speed
Tilt Movemement range Stand.
Reduc.
Microphone Sen-
sitivity
1-10-20
Blackout Settings Blackout During M.C. Off, On
Blackout while: Pan/Tilt moving Off, On
Colour Mixing
mode
RGBW, CMY
Dimmer Curve Linear
Theatrical
Zoom Mode Beam
Wash
Colour Calibration
Mode
Off, On
Init Effect Positions Pan 0-255
:
Dimmer Fine 0-255
Screen Settings Display Intensity 1-10
Screen Saver Delay Off-10min.
Touchscreen Lock Off-10min.
Recalibrate Touch-
screen
Display Orientation Normal
Inverted
Auto
Temperature Unit °C,°F
Fan Mode Auto
High
Theatre mode On, Off
Date & Time Settings
Default Settings
Manual Control Reset Functions Total System Reset
Pan/Tilt reset
Zoom Reset.
Preset Effect Con-
trol
Pan Position 1-Position 5
:
Dimmer Position 1- Position 5
Manual Effect Con-
trol
Pan 0-255
:
Dimmer Fine 0-255

17
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Stand -Alone Test Sequences Dynamic Mode
Static Mode Pan 0-255
Tilt 0-255
Zoom 0-255
MusicTrigger Off, On
Preset Playback None
Test
:
Prog. 3
Play Program Play Program 1
Play Program 2
Play Program 3
Edit Program Edit Program 1 Start Step 1-100
End Step 1-100
Edit Program Steps Step 1 Pan (0-255)
: :
:Dimmer Fine
(0-255)
: Step Time
(0-25.5s)
Step 100 Pan (0-255)
:
Dimmer Fine
(0-255)
Fade Time
(0-25.5s)
Service Adjust DMX Values Pan 0-255
:
Dimmer Fine 0-255
Calibrations Calibrate Effects Pan 0-255
Tilt 0-255
Calibrate colours Red 0-255
Green 0-255
Blue 0-255
White 0-255
Load Default Calibra-
tions
Update Software

18
Robin 1200 LEDWash - DMX chart
Version 1.4
Mode/Channel Value Function Type of
control
1 2 3 4 5 6
1 1 1 1 1 1 0-255
Pan (8 bit)
Pan movement by 450° proportional
2 2 2 2 2 2 0-255
Pan Fine (16 bit)
Fine control of pan movement proportional
3 3 3 3 3 3 0-255
Tilt (8bit)
Tilt movement by 300° proportional
4 4 4 4 4 4 0-255
Tilt ne (16 bit)
Fine control of tilt movement proportional
5 5 5 5 5 5
0
1 - 255
1 - 255
Pan/Tilt speed, Pan/Tilt time
Max. speed (tracking mode)
P./T. speed-set Speed Mode in menu: P./T. Mode
Speed from max. to min. (vector mode)
P./T. time - set Time Mode in menu: Pan/Tilt Mode
Time from 0.1 s to 25.5 s.
step
proportional
proportional
6 6 6 6 6 6
0 - 9
10 - 14
15 - 19
20 - 29
30 - 39
40 - 49
50 - 59
60 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 114
115 - 119
120 - 139
140 - 149
150 - 179
180 - 189
190 - 199
200 - 209
210 - 255
Special functions
Reserved
To activate following functions , stop in DMX value
for at least 3sec. and shutter must be closed at least
3sec. (Shutter channel 43/19/14/9/9 must be at ran-
ge of 0-31DMX). Corresponding menu items are
temporily overrided except DMX input!
DMX input: Wired DMX *
DMX input: Wireless DMX*
* function is active only10 seconds after switching the xture on
Reserved
RGBW colour mixing mode
CMY colour mixing mode
Pan/Tilt speed mode
Pan/Tilt time mode
Blackout while pan/tilt moving
Disabled blackout while pan/tilt moving
Theatre mode On
Theatre mode Off
Zoom mode: Wash
Zoom mode:Beam
Reserved
To activate following reset function, stop in DMX
value for at least 3 sec.
Pan/Tilt reset
Reserved
Zoom reset
Reserved
Total reset
Reserved
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
The following colour channels will behave accordingly what colour mixing mode (RGB or CMY) is selected at
channel "Special Functions". RGBW mode is default.
- 7 7 - - - 0-255
Red/Cyan (8 bit) - all zones
Red or cyan colour saturation control (0-100%) proportional
- 8 - - - - 0-255
Red/Cyan ne(16 bit) - all zones
Fine red or cyan colour saturation control proportional
- 9 8 - - - 0-255
Green/Magenta (8 bit) - all zones
Green or magenta colour saturat. control (0-100%) proportional
- 10 - - - - 0-255
Green/Magenta (16 bit) - all zones
Fine green or magenta colour saturation control proportional

19
Mode/Channel Value Function Type of
control
1 2 3 4 5 6
- 11 9 - - - 0-255
Blue/Yellow (8 bit) - all zones
Blue or yellow colour saturation control (0-100%) proportional
- 12 - - - - 0-255
Blue/Yellow (16 bit) - all zones
Fine blue or yellow colour saturation control proportional
- 13 10 - - - 0-255
White (8 bit) - all zones
If RGBW mode is selected:
White colour saturation control coarse (0-100%)
If CMY mode is selected:
No function
proportional
- 14 - - - - 0-255
White (16 bit) - all zones
Fine white colour saturation control (RGBW mode) proportional
7 - - - 14 7 0-255
Red/Cyan(8 bit) - zone 1
Red or cyan colour saturation control (0-100%) proportional
8 - - - 15 8 0-255
Red/Cyan (16 bit) - zone 1
Fine red or cyan colour saturation control proportional
9 - - - 16 9 0-255
Green/Magenta (8 bit) - zone 1
Green or magenta colour saturat. control (0-100%) proportional
10 - - - 17 10 0-255
Green/Magenta (16 bit) - zone 1
Fine green or magenta colour saturation control proportional
11 - - - 18 11 0-255
Blue/Yellow (8 bit) zone 1
Blue or yellow colour saturation control (0-100%) proportional
12 - - - 19 12 0-255
Blue/Yellow (16 bit) zone 1
Fine blue or yellow colour saturation control proportional
13 - - - 20 13 0-255
White (8 bit) - zone 1
If RGBW mode is selected:
White colour saturation control coarse (0-100%)
If CMY mode is selected:
No function
proportional
14 - - - 21 14 0-255
White (16 bit) - zone 1
Fine white colour saturation control (RGBW mode) proportional
15 - - - 22 7 0-255
Red/Cyan ( 8bit) - zone 2
Red or cyan colour saturation control (0-100%) proportional
16 - - - 23 8 0-255
Red/Cyan (16 bit) - zone 2
Fine red or cyan colour saturation control proportional
17 - - - 24 9 0-255
Green/Magenta (8 bit) - zone 2
Green or magenta colour saturat. control (0-100%) proportional
18 - - - 24 10 0-255
Green/Magenta (16 bit) - zone 2
Fine green or magenta colour saturation control proportional
19 - - - 26 11 0-255
Blue/Yellow (8 bit) zone 2
Blue or yellow colour saturation control (0-100%) proportional
20 - - - 27 12 0-255
Blue/Yellow (16 bit) zone 2
Fine blue or yellow colour saturation control proportional
21 - - - 28 13 0-255
White (8 bit) - zone 2
If RGB mode is selected:
White colour saturation control coarse (0-100%)
If CMY mode is selected:
No function
proportional
22 - - - 29 14 0-255
White (16 bit) - zone 2
Fine white colour saturation control (RGBW mode) proportional
23 - - - 30 15 0-255
Red/Cyan (8bit) - zone 3
Red or cyan colour saturation control (0-100%) proportional
24 - - - 31 16 0-255
Red/Cyan (16 bit) - zone 3
Fine red or cyan colour saturation control proportional
25 - - - 32 17 0-255
Green/Magenta (8 bit) - zone 3
Green or magenta colour saturat. control (0-100%) proportional

20
Mode/Channel Value Function Type of
control
1 2 3 4 5 6
26 - - - 33 18 0-255
Green/Magenta (16 bit) - zone 3
Fine green or magenta colour saturation control proportional
27 - - - 34 19 0-255
Blue/Yellow (8 bit) zone 3
Blue or yellow colour saturation control (0-100%) proportional
28 - - - 35 20 0-255
Blue/Yellow (16 bit) zone 3
Fine blue or yellow colour saturation control proportional
29 - - - 36 21 0-255
White (8 bit) zone 3
If RGB mode is selected:
White colour saturation control coarse (0-100%)
If CMY mode is selected:
No function
proportional
30 - - - 37 22 0-255
White (16 bit) zone 3
Fine white colour saturation control (RGBW mode) proportional
31 - - - 38 23 0-255
Red/Cyan ( 8bit) - zone 4
Red or cyan colour saturation control (0-100%) proportional
32 - - - 39 24 0-255
Red/Cyan (16 bit) - zone 4
Fine red or cyan colour saturation control proportional
33 - - - 40 25 0-255
Green/Magenta (8 bit) - zone 4
Green or magenta colour saturat. control (0-100%) proportional
34 - - - 41 26 0-255
Green/Magenta (16 bit) - zone 4
Fine green or magenta colour saturation control proportional
35 - - - 42 27 0-255
Blue/Yellow (8 bit) zone 4
Blue or yellow colour saturation control (0-100%) proportional
36 - - - 43 28 0-255
Blue/Yellow (16 bit) zone 4
Fine blue or yellow colour saturation control proportional
37 - - - 44 29 0-255
White (8 bit) zone 4
If RGB mode is selected:
White colour saturation control coarse (0-100%)
If CMY mode is selected:
No functin
proportional
38 - - - 45 30 0-255
White (16 bit) zone 4
Fine white colour saturation control (RGBW mode ) proportional
39 15 11 - 12 31 0
1-255
CTC
No function
Colour temperature correction from 19000K to
2700K
step
proportional
40 16 12 7 13 32
0
1-2
3
4-5
6
7-9
10-12
13-15
16
17-55
56
57 - 95
96
97 – 134
135
136 - 174
175
176 -214
Virtual Colour Wheel
For detailed description see " Virtual colour wheel- colour mixing chart
No function
White 2700 K
White 2700 K (Halogen lamp mode*)
White 3200 K
White 3200 K (Halogen lamp mode*)
White 4200 K
White 5600 K
White 8000 K
Blue (Blue=full, Red+Green+White=0)
Red=0, Green->up,Blue =full, White=0
Light Blue (Red=0, Green=full, Blue =full, White=0)
Red=0, Green=full, Blue->down, White=0
Green (Red=0, Green=full, Blue =0, White=0)
Red->up, Green=full, Blue=0, White=0
Yellow (Red=full, Green=full, Blue=0, White=0)
Red=full, Green->down, Blue=0, White=0
Red(Red=full, Green=0, Blue=0, White=0)
Red=full, Green=0, Blue->up, White=0
step
step
step
step
step
step
step
step
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional