Robe Ambiane User manual

1
User manual
Ambiane TW
The unit generates colored light by means of high power LEDs. The product was designed for indoor use only.
1. Attention
  Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall
national and local electrical and construction codes and regulations.
Avoid looking directly into the LED light beam at close range!
  Donotinstalltheunitnearhighlyinammableliquidsormaterials.
Do not allow anything to rest on the unit.
Do not use the unit near high humidity or water or expose to rain.
  Donotinstalltheunitnearanopename.
Do not install the unit in dirty,dusty or badly ventilated location.
  Su󰀩cientairaccessingtothehousingoftheunithastobeensured,
there must not be any heat or anti-noise insulation within a 0.6m x 0.6m
  areaaroundtheunit(non-ICratedxture).
Alvays switch o󰀨 power suply of the unit before connecting or disconnecting the unit
2. Installation
1.Prepareacircularopeninginthelowerceiling(1)asshowninthepicturebelow.
2.InserttheAmbianeunitintotheopening.Fastenthexturebymeansoftwospringfasteners(2)totheopening

2
Toconnectneededcablestothexture,unscrewtwoscrews(4)fromtheplasticcover(3).
Theconnectionblocks(5)havethefollowingwiring:
Theprimarypowerinputservesforastandardpower(e.g.ArcPowerforAmbiane).
Thesecondarypowerinputservesforabackuppower(incasethatprimarypowerfailed).
If both power inputs are under voltage, the primary power has a priority and the secondary power is disabled.
In case of primary power loss, the secondary power is enabled.
Ifthextureissuppliedviathesecondarypower,thelightoutputofthextureisawhitecolour(3200K)andits
light intensity can be set by a trimmer.
Thexturecanbecontrolledbyoneofthefollowingmethods:DMX512
DALI
ThextureisequippedwithtwoDMXandDALIconnectionblocksforeasyconnectiontoDMXorDALIchain
(In/Outmethod).
DMX connection Power connection
PCB Function PCB Function
0V - Shield + Power +
 D+ Signal(+)    - Power-
 D- Signal(-)
3. DMX and DALI address setting and control
TheDIPswitch,locatednexttotheconnectionblocks,allowstorunatestlightandswitchthexturetothe
update mode in case of software update.

3
DIP10-ifswitchedtoON=testlight(thexturelightsat3200K)
DIP11-hastobeswitchedtoOFFpositiontoreceiveDMX512orDALI
DIP12-changefromOFFtoONpositionswitchesthexturetotheupdatemode.
DMX control
TheDMXstartaddress,istherstchannelusedtoreceiveinstructionsfromtheDMXcontroller.Theaddress
maybeanychannelfrom1to510.DMXaddresscanbeseteitherbyDIPswitchorbyRDM.DMXaddress
setbyRDMoverwritesaddresssetbyDIPswitchandviceversa.
DIP11hastobesetinOFFposition.DALIcommandshaveprioritytoDMXoperation.
ExampleofDMXaddresses:
DALI control
AddressingofthextureismadebymeansofanexternalDALIcontroller.TheexternalDALIcontrollerhasto
sendactivatingcommand(1=ON)tostartcontrolofthexture(anddeactivatingcommand(0=OFF)tostop
controlofthexture).
DIP11hastobesetinOFFposition.DALIcommandshaveprioritytoDMXoperation.
4.RDM
ThisxturesupportsRDMoperation.RDM(RemoteDeviceManagement)isabi-directionalcommunication
protocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512devicecongurationand
status monitoring.
RDMallowsyoutosetDMXaddressandreadoutsoftwareversionofthexture.
5. Anti-glare ring installation
Inserttheanti-glarering(1)intothextureuntilthreelocks(2)snapintoslots(3).

4
6.DMX protocol (version 1.1)
Channel Value Function Type of control
10-255
White colour selection
Whitefrom2700K-->6500K(128DMX=4000K) proportional
20-255
Dimmer coarse
Lightintensitycoarse0%-->100% proportional
30-255
Dimmer ne
Lightintensityne0%-->100% proportional
7.Technical specications
Inputvoltage:     24VDC
Max.powerconsumption:   40W
Beamangle:     67°,80°withanti-glarering
Colourtemperature:    2700K-6500K
Control:     DMX,DALI
      RDMcompatible
DMXchannels:     3
TypicalLumenmaintenance:   70%@50,000hours
Ledlifeexpectancy:    minimum50,000hours
Operatingambienttemp.range:  -20°C/+45°C(-4F/+113F)
Operatingtemperature:   75°C@Ambient+35°C(167°F@Ambient+95°F)
Totalheatdissipation:    136BTU/h(calculated)
Cooling:     convection
Totalheatdissipation:    136BTU/h(calculated)
Housing:     alluminium
Weight:     1.8kg
Installationmethod:    viatwospringfasteners
Protectionfactor:    IP20
ICrating:     non-ICrated
Power/DMX/DALIconnection:   screwconnectionblockDegsonDG306-5.0-02P
      (Wirerange:22-14AWG(UL),1.5mm2 (IEC))
8. Optional Accessories
ArcPowerforAmbiane(P/N10063035)
Anti-GlareRing(P/N10980386)
Di󰀨userGlassFrosted(P/N10980387)
AdapterRing(230-255mm)(P/N10980388)
9. Maintenance
Keepthextureclean,especiallylightsourceandtheribbedhousing.

5
10.Dimensions
mm [inch]
5
Version2.0June23,2017
Specications are subject to change without notice.
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici