Roca Z856584406 User manual

123
?
?
4
5 6 7
b
8mm
a
Place the cabinet in the desired position and
mark a line along the top
Assemble the Hang ‘N’ Lock
bracket and measure the
distance between the top of
the cabinet and the bottom
of the bracket.
Use that measurement to create a line
underneath the one previously marked.
Rest the Hang N Lock bracket on this new line
and mark the screw holes.
Drill screw holes and insert wall plugs.
Mount the bracket onto the wall. Do not insert
the screws fully. Make the bracket level by rotating the CAM mechanisms. Fully tighten the screws.
CAB 132 R01
bx5
cx1
ax4
d
ex1
fx1
gx1
hx1
ix2
x8 (x16)
FIXING PACK
x2 MAX
10kg
MAX
5kg
6mm8mm
image for reference only
Size of Hang ‘N’ Lock may be dierent
depending on the length of cabinet.

13 14 15 16
17 18 20
Ensure that the domestic electrical mains
supply to which the cabinet is to be connected
is turned o.
Connect the flexible mains supply cable on the
back of the cabinet to the domestic electrical
mains supply ensuring that the Live (Brown)
conductor is connected to the Live on the
domestic electrical mains supply, the Neutral
(Blue) conductor is connected to the Neutral on
the domestic electrical mains supply and the
Earth (Yellow/Green) conductor is connected
to the Earth/Ground on the domestic electrical
mains supply.
Note: connection of the product to the
domestic electrical mains supply must only be
carried out by a Building Regulations Part P
certified electrician or must be checked by your
Local Authority Building Control Department.
CONNECTING ELECTRICITY
e
g
f
h
i
1
0
19
d
910 11 12
Tape wire through
the gap in the
back bracket.
d
Tape wire through gap in the back bracket. Mount the overhead light to the top of the
cabinet and connect the wire. Hang the cabinet on the bracket. Mark screw hole at the bottom of the cabinet
Take the cabinet o the bracket. Drill screw holes and insert wall plugs.
6mm
Re-hang the cabinet. Lock the cabinet by inserting and rotating the
locking components. Insert the shelf brackets and shelves. If necessary adjust the door to make level.
b
Check to see
if electrics are
functioning.
CONNECTING ELECTRICITY

Please read all of the information carefully.
Safety & Care
1. Always take care when using power tools, particularly if there is any
water in the working area.
2.Do not use power tools for assembling or fitting the cabinet including
power drills and power screwdrivers.
3. The wall plugs supplied are for use on solid walls only. For cavity walls
or plasterboard use specialist fixings that are suitable for the type of wall
construction.
4. To retain the best quality finish, clean product regularly with a soft
damp cloth.
5. Do not use abrasive or chemical cleaners, as these will damage the
product.
6. The max load of the cabinet is 10kg when fitted to a solid wall and 5kg
when fitted to a cavity wall.
7. When drilling into a tiled surface do not use a hammer drill.
8. Always use a drill bit that is suitable for the surface that is being
drilled.
9. Do not slam the door open, as this may damage the hinge.
THIS IS A CLASS 1 APPLIANCE AND MUST BE CONNECTED TO EARTH
INPUT: 220-240Vac 5A IP RATING: IP44
HAZARDOUS VOLTAGES INSIDE – DO NOT REMOVE ANY COVERS
LAMP TYPE LED
In accordance with Statutory Instrument 2010 No. 2214 - The Building
Regulations 2010 the installation of this product must be either;
• carried out by an electrician who is a member of a competent person
self-certification scheme who will certify the work complies with the Building
Regulations and you do not need to notify your local authority, or,
• carried out after prior notification to the Local Authority Building Control
Department, which has responsibility for ensuring that the work is inspected and
tested.
In accordance with the Building Regulations 2010 Approved Document P,
connection to the fixed wiring of the mains electrical supply must comply with
the current revision of the IET Wiring Regulations BS 7671.
IMPORTANT WARRANTY INFORMATION
In accordance with Statutory Instrument 2010 No. 2214 - The Building
Regulations 2010 the installer must give the occupier of the premises in which
this product has been installed a certificate to confirm that the requirements of
regulations 4 and 7 have been satisfied within 30 days, or the installation of this
product must be inspected and tested by the Local Authority Building Control
Department who will issue a compliance certificate.
A copy of this certificate may be required for certain warranty claims. Failure to
provide a copy of the certificate may invalidate the warranty.
image for reference only
Roca Ltd.
Samson Road, Hermitage Industrial Estate, Coalville, Leicestershire, LE67 3FP
Telephone [phone]
www.uk.roca.com
This cabinet is rated IP44 and must only be installed with all electrical
connections and components in Zone 2 and Outside Zones, shown below.
Ensure that the access to the domestic mains electrical supply is located
behind the intended mounting position for the cabinet.

Declarations of conformity