Rockford Fosgate 1000 Owner's manual

p
owe
r
®
2-channel
2-channel
trans• ana
trans• ana
trans• ana
trans• nova
4-channel
2-channel
2-channel
trans• ana
4-channel
trans• ana
Power AMPLIFIER
INSTALLATION & OPERATION
® ®
car audio
fanatics
for

POWER 360 POWER 400 POWER 500 POWER 800 POWER 800 POWER 1000
2-channel 4-channel 2-channel 2-channel 4-channel 2-channel
Dynamic Power Rating
(IHF-202 Standard) - Measured at 14.4 Volts
Mono into a 4ΩLoad
481 Watts x 1 232 Watts x 2 710 Watts x 1 960 Watts x 1 525 Watts x 2 1460 Watts x 1
Per channel into a 2ΩLoad
242 Watts x 2 127 Watts x 4 330 Watts x 2 480 Watts x 2 270 Watts x 4 730 Watts x 2
Per channel into a 4ΩLoad
154 Watts x 2 84 Watts x 4 210 Watts x 2 240 Watts x 2 150 Watts x 4 450 Watts x 2
Continuous Power Rating
(Competition Standard) - Measured at 13.8 Battery Volts
RMS continuous power per channel,
90 Watts x 2 50 Watts x 4 125 Watts x 2 200 Watts x 2 100 Watts x 4 250 Watts x 2
both channels driven into a 4Ωload
from 20 to 20,000 Hz with less than
0.05% Total Harmonic Distortion (THD)
RMS continuous power per channel,
180 Watts x 2 100 Watts x 4 250 Watts x 2 400 Watts x 2 200 Watts x 4 500 Watts x 2
both channels driven into a 2Ωload
from 20 to 20,000 Hz, with less than
0.1% Total Harmonic Distortion (THD)
RMS continuous power mono into a
360 Watts x 1 200 Watts x 2 500 Watts x 1 800 Watts x 1 400 Watts x 2 1000 Watts x 1
4Ωload from 20 to 20,000 Hz, with
less than 0.1% Total Harmonic Distortion (THD)
Signal-to-Noise Ratio (A-weighted) >100dB >100dB >100dB >100dB >100dB >100dB
Crossover Slope (Butterworth) 24dB/octave 24dB/octave 24dB/octave 24dB/octave 24dB/octave 24dB/octave
Crossover Frequency
50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz
Specifications are subject to change without notice.
S
PECIFICATIONS
– i –

POWER 360 POWER 400 POWER 500 POWER 800 POWER 800 POWER 1000
2-channel 4-channel 2-channel 2-channel 4-channel 2-channel
Dimensions (end caps installed)
2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H
9.60" (24.38cm) W
9.60" (24.38cm) W
9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W
12.27" (31.16cm) L 13.27" (33.70cm) L 13.27" (33.70cm) L 18.27" (46.40cm) L 18.27" (46.40cm) L 18.27" (46.40cm) L
Heatsink Type (internal use only) #3 #4 #4 #6 #6 #6
Frequency Response (±0.5dB) 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz
Bandwidth (±3dB) 20Hz - 200kHz 20Hz - 200kHz 20Hz - 200kHz 20Hz - 200kHz 20Hz - 200kHz 20Hz - 200kHz
Damping Factor @ 4Ω(at output connector) >200 >200 >200 >200 >200 >200
Slew Rate 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs
IM Distortion (IHF) <0.05% <0.05% <0.05% <0.05% <0.05% <0.05%
Source Unit Compatibility (+15dB gain overlap)
17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA)
Input Sensitivity (+0dB gain overlap) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA)
Protection NOMAD - Internal analog-computer output protection circuitry limits power in case of
overload. Thermal switch shuts down the amplifier in case of overheating.
Battery Fuse Rating (External to Amplifier) 40A 50A 50A 60A* 60A* 2-50A or 1-100A*
Fuse Type ATC AGU AGU AGU AGU 2-AGU OR 1- ANL
Equalization (45Hz Punch Bass) Variable Rear Variable Variable Variable Rear Variable Variable
(0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB)
Input Impedance 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms
* recommended fuse not supplied with amplifier
Specifications are subject to change without notice.
– ii –

Dear Customer,
Congratulations on your purchase of the world's finest brand of car audio amplifiers.
AtRockfordFosgatewearefanaticsaboutmusicalreproductionatitsbest,andweare
pleasedyouchoseourproduct.Throughyearsofengineeringexpertise,handcraftsman-
ship and critical testing procedures, we have created a wide range of products that
reproduce music with all the clarity and richness you deserve.
For maximum performance we recommend you have your new Rockford Fosgate
product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized
training through Rockford Technical Training Institute (RTTI). Please read your
warranty and retain your receipt and original carton for possible future use.
Greatproductandcompetent installationsareonlyapieceofthepuzzle whenitcomes
to your system. Make sure that your installer is using 100% authentic installation
accessories from Connecting Punch in your installation. Connecting Punch has
everything from RCA cables and speaker wire to Power line and battery connectors.
Insist on it! After all, your new system deserves nothing but the best.
To add the finishing touch to your new Rockford Fosgate image order your Rockford
wearables,which include everything from T-shirts and jackets tohats and sunglasses.
To get a free brochure on Rockford Fosgate products and Rockford accessories, in the
U.S.call480-967-3565orFAX480-967-8132.Forallothercountries,call+001-480-
967-3565 or FAX [phone].
If, after reading your manual, you still have questions regarding this product,
we recommend that you see your Rockford Fosgate dealer. If you need further
assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial
number, model number and date of purchase available when you call.
PRACTICE SAFE SOUND™
CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB
MAY CAUSE PERMANENT HEARING LOSS.HIGH POWERED AUTOSOUND
SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER
130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.
The serial number can be found on the outside of the box. Please record it in
the space provided below as your permanent record. This will serve as
verificationofyourfactorywarrantyandmaybecomeusefulinrecoveringyour
amplifier if it is ever stolen.
Serial Number: ________________________________
Model Number:________________________________
– iii –

T ABLE OF C ONTENTS
Specifications.............................................................................................. i
Introduction................................................................................................1
Power Amplifier Accessory Pack ................................................................... 1
Feature Chart..............................................................................................2
Design Features .......................................................................................... 3
Installation Considerations ........................................................................... 7
Mounting Location ...................................................................................... 8
Battery and Charging ..................................................................................9
Wiring the System....................................................................................... 9
Using Passive Crossovers........................................................................... 11
Table of Component Values........................................................................ 12
Installation ...............................................................................................13
Operation................................................................................................. 21
System Diagrams...................................................................................... 24
Troubleshooting........................................................................................ 28
Dynamic Power Measurements................................................................... 31
Warranty Information ................................................................................ 33
International Information............................................................................34
Sections marked
ADVANCED OPERATION
include in-depth
technical information
Sections marked
TROUBLESHOOTING
include recommendations for
curing installation problems
Sections marked
INSTALLATION
include “slam dunk”
wiring connections
I
N
S
T
A
L
L
A
T
I
O
N
+ -
+ -
TROUBLE-S
H
O
O
T
I
N
G
?
Welcometo Rockford Fosgate! This manual is designedto provide information
for the owner, salesperson and installer. For those of you who want quick
information on how to install this product, please turn to the Installation
Section of this manual or refer to the icons listed below. Other information can
be located by using the Table of Contents. We, at Rockford Fosgate, have
workedveryhardtomakesurealltheinformationinthismanualiscurrent.But,
asweareconstantlyfindingnewwaystoimproveourproduct,thisinformation
is subject to change without notice.
GETTING STARTED
a
d
v
a
n
c
e
d
O
p
e
r
a
t
i
o
n
+

I NTRODUCTION
Rockford engineers designed the Power amplifiers to provide an awesome
amountofpowerwhiledeliveringsuperiorsoundqualityinaconvenientand
efficient package. The TRANS• ana & patented TRANS• nova topologies are
lowvoltagecircuitsusedinthepreampstageofthePoweramplifiersthatlet
the music sound crystal clear and very real, even when played at high
volumelevels.ThisismatchedwithTOPAZ,auniquegroundingcircuitused
to eliminate noise problems associated with car audio systems and their
installation. The use of a protection circuit called NOMAD, along with
MOSFET, DSM (Discrete Surface Mount) and innovative MEHSA heat
dissipating technologies improves amplifier efficiency. The result of these
components give the Power amplifier awesome sound quality in a “Bullet
Proof” package.
– 1 –
P OWER A MPLIFIER A CCESSORY P ACK
The accessory pack shipped with the Power amplifiers includes the mounting
hardware necessary to secure the amp to the vehicle.
Installation & Operation Manual
Punch Verification Certificate
(4) Amplifier mounting screws (#8 x 3/4" Phillips)
(4) Speaker/Power connector set screws (3/32" Allen)
(4) Endbell mounting screws (9/64" Allen)
(1) Allen wrench (3/32")
(1) Allen wrench (9/64")
(1)Inlinefuseholder(Power360,Power400 &Power5002-channelamps)
(1) AGU 40 amp fuse (Power 360 2-channel amp)
(1) AGU 50 amp fuse (Power 400 4-channel & Power 500 2-channel amps)
(1) Remote Punch Bass (replacement part #WP-2429)
(1) 15' Remote Punch Bass cable (replacement part #CC-2421)
(2) Remote Punch Bass bracket screws (4 x 7/16" Phillips)
NOTE: Refer to the specifications section for recommended fuse sizes on the
Power8002-channel,Power8004-channel&Power10002-channelamps.

POWER AMPLIFIER MODEL Power Power Power Power Power Power
360 400 500 800 800 1000
# of CHANNELS 2422 42
Stable Into: (stereo/mono) 2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω2Ω/4Ω
CIRCUITRY
1
TRANS• ana – circuit topology xxxx x–
TRANS• nova – patented circuit topology
2
–––– –x
DIAMOND – patented MOSFET driver stage
3
–––– –x
Class-G – high efficiency topology –––– ––
MEHSA – heat dissipating technology xxxx xx
TOPAZ – patented noise eliminating circuitry
4
xxxx xx
DSM – discrete surface mount xxxx xx
MOSFETs – power supply & output devices xxxx xx
NOMAD – protection circuit xxxx xx
FEATURES
Die Cast Heatsink
5
xxxx xx
Hi-Level Inputs – for factory radios –––– ––
RCA Inputs – for aftermarket radios xxxx xx
Input Switches – eliminates “Y” adaptors –x–– x–
Pass-Thru – feeds signal to aux. amp xxxx xx
Pwr/Spk Screw Terminals –––– ––
Pwr/Spk Block Terminals xxxx xx
4 Gauge PWR/GND xxxx xx
Variable Punch Bass (0dB ~+18dB @ 45Hz) Remote Remote Rear Remote Remote Remote Rear Remote
Variable Xover (50Hz ~ 210Hz) HP/FULL/LP
6
HP/FULL/LP
6
HP/FULL/LP
6
HP/FULL/LP
6
HP/FULL/LP
6
HP/FULL/ LP
6
Crossover Slope (Butterworth) 24dB 24dB 24dB 24dB 24dB 24dB
Phase Warp (0
0
~ 180
0
)–––– –x
1Additional information on features, specifications and system designs can be found at: www.rockfordfosgate.com
2Trans•nova is patented under "U.S. Patent No. 4,467,288"
3DIAMOND is patented under "U.S. Patent No. 5,673,000"
4TOPAZ is patented under "U.S. Patent No. 5,751,823"
5Diecast Heatsink is patented under "U.S. Patent No. D401,225"
6HP = 24dB/octave High-Pass / LP = 24dB/octave Low-Pass / FULL = Full Range
7Recommended fuses not supplied with amplifier – 2 –
P OWER A MPLIFIER F EATURE C HART

– 3 –
D ESIGN F EATURES
Power 360
2-channel
Power 400
4-channel
Speaker
+ L -
Crossover Frequency
Left Gain Input
Pass-Thru
LR
LR
Right
Gain Remote
Punch Bass
HP-Full-LP
Crossover
Speaker
+ R -
65
80
55
50
110
210 Hz
145
190
REM
B+ GND
LED
52
9
8
77
9
2
6
1
10 32
2
2
6
4571
LR+ LR- RR+ RR- B+ GND LF- LF+ RF+RF-
REM LED
Front
Crossover
HP-Full-LP
4/2
Input Front
Gain Front
Crossover
Frequency
65
80
55
50
110
210 Hz
145
190
Front Pass-Thru Rear
RR
LL
Rear
Crossover
Frequency
65
80
55
50
110
210 Hz
145
190
Rear
Gain
Rear
Crossover
HP-Full-LP Rear
Remote
Punch
Bass
98
79
10
32
99

– 4 –
Power 500
2-channel
Power 800
2-channel
Speaker
+ L -
Crossover Frequency
Left Gain Input
Pass-Thru
LR
LR
Right
Gain Remote
Punch Bass
HP-Full-LP
Crossover
Speaker
+ R -
65
80
55
50
110
210 Hz
145
190
REM
B+ GND
LED
52
9
8
77
9
2
6
1
10 32
10
21
2
3
6
8 99 572 7
B+ GND
LED
REM
Speaker
+ L -
Crossover Frequency
Left Gain Input
Pass-Thru
LR
LR
Right
Gain Remote
Punch Bass
HP-Full-LP
Crossover
Speaker
+ R -
65
80
55
50
110
210 Hz
145
190

– 5 –
Power 800
4-channel
1
2
6
899 774 59 9
310
2 2
LED
LR+ LR- RR+ RR- B+ GND LF- LF+ RF+RF-
REM
Front
Crossover
HP-Full-LP
4/2
Input Front
Gain Front
Crossover
Frequency
65
80
55
50
110
210 Hz
145
190
Front Pass-Thru Rear
RR
LL
Rear
Crossover
Frequency
65
80
55
50
110
210 Hz
145
190
Rear
Gain
Rear
Crossover
HP-Full-LP Rear
Remote
Punch
Bass
Power 1000
2-channel
21
2
8 99 572 7
3
6
10
11
65
80
55
50
110
210 Hz
145
190
HP–Full–LP
Crossover
Input
Pass-Thru
LR
LR
Crossover
Frequency
Speaker
+ L - Speaker + R -
Right
Gain
Left
Gain
Remote
Punch Bass
Phase
Warp
B+ GND
LED
REM