Rockford Fosgate iPod Interface Module Guide

Serial Number: Date of Purchase:
Installation & Operation
®
Interface Module
for selected BMW/Mini Cooper vehicles

2
Contents
Introduction and Precautions................................... 2
Supported iPod Models ............................................. 3
Pre-System Setup ...................................................... 4
Installation...............................................................5-6
Operation ................................................................6-8
Auxiliary Audio Source ............................................. 9
Troubleshooting ....................................................... 10
Warranty .................................................................. 11
Introduction and Precautions
Thank you for purchasing the Rockford Fosgate Interface Module for iPod.The Interface
Module was designed and manufactured to seamlessly integrate with your vehicle’s factory
system.To get the best performance from this device, read this manual before doing any
type of installation.
Practice Safe Sound™
Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss. High powered auto sound systems may produce sound pressure levels
well over 130dB. Use common sense and practice safe sound.
This symbol with “CAUTION” is intended to alert the user to the
presence of important instructions. Failure to heed the instructions can
result in injury, damage to the vehicle or unit damage.
CAUTION:To prevent injury and damage to the unit, please read and
follow the instructions in this manual.We want you to enjoy
this system, not get a headache.
CAUTION:If you feel unsure about installing this system yourself, have it
installed by a qualified Rockford Fosgate technician.
CAUTION:Before installation, disconnect the vehicle battery, both
positive (+) and negative (-) terminals, to prevent damage to
the unit, fire and/or possible injury.
CAUTION:For your safety, ensure the iPod interface module is mounted
in a location that will not interfere with the proper and safe
operation of the vehicle.
©2009 Rockford Corporation.All rights reserved.
Rockford Fosgate and the Rockford Fosgate logo, are either registered trademarks
or trademarks of Rockford Corporation.
iPod is a trademark of Apple, Inc.

3
Supported iPod Models
iPod Firmware
For proper operation of the interface module, ensure your iPod is updated with the
latest firmware. Free updates can be downloaded from http:/www.apple.com/ipod/
download/.The directions on the site will guide you through the update process.

4
Pre-System Setup
Interface Module DIP Switch Settings
Proper identification of your system and correct setting of the DIP switches will ensure the
interface module operates properly when installed.
NOTE: If you change the positions of the DIP switches after the module is installed, turn
off the vehicle ignition, disconnect the ‘Vehicle Harness’ from the interface module, then
wait one (1) minute before reconnecting the harness and turning the vehicle ignition on.
ON 12
Interface Module
DIP Switch Positions
12 ON 12
ON
OFF
Car
Switch
iPod
Switch
This setting provides slower text refreshing to allow
flawless operation of these radios.
Interface Module
12
ON
12
Car Switch iPod Switch
Switch 1
ON
Switch 2
OFF
Set Car Switches to;
12
Interface Module
CDC–1(CD Changer–1) setting
CDC–2(CD Changer–2) setting
12
ON
12
Car Switch
iPod Switch
Both
Switches
OFF
(Default)
Set Car Switches to;
12
Both
Switches
OFF
(Default)
Recommended for use when Text Display is
NOT supported by the radio.
Recommended for late model Business CD and
Navigation radio systems.
Recommended for early model Business CD and
Business cassette radio systems.
NOTE: The first button press only clears the text from the radio,
the second button press executes the command.
Recommended for use when Text Display is
supported by the radio .
˝Radio˝
Both
Switches
ON
˝iPod˝
Use this mode to browse within the contents of
the iPod by category as shown in the ‘Operation’ section.
Set iPod Switches to;
Content is selected on the iPod.
Content is only selected from
the radio and the iPod is locked.
Track numbers and times are not synchronized between the
iPod and radio. This mode has the fastest response time.
Interface Module
12
O
N
12
Car Switch iPod Switch
12
Set iPod Switches to; Interface Module
1
2ON
12
Car Switch iPod Switch
12
DIP Switch Setting for iPod Switch on the Interface Module
DIP Switch Setting for Car Switch on the Interface Module

5
Installation
It is recommended that installation only be performed by a qualified professional. Beware
of sharp edges to avoid injury and exercise caution when removing trims as they may
break.The module should be placed at an accessible location to allow an AUX cable to
be connected, such as in the glove box, the center console or under the front seat. Ensure
the mounting location does not interfere with the safe operation of the vehicle (i.e.. near
steering, foot pedal controls, parking brake or shifter).
1. Be sure to carefully read and understand the instructions before attempting to install
the unit.
2. Disconnect both battery terminals.These cables must be disconnected during
installation to ensure proper initialization of the interface module when it is connected.
NOTE: On some vehicles you will need to access the trunk area.
3.
Locate your CD Changer harness as follows;
In most vehicles this will be located in the trunk on the left hand side (driver’s).
BMW X3 – Harness is located underneath carpeting under the center console.
BMW Z4 – Harness is located between the seats, underneath subwoofer.
Mini Cooper/Cooper S – Harness is located on the right hand side (passenger)
of the trunk area.
4. DSP Integration – To see if your vehicle
has DSP look for a bare metal coax cable
and a 3-pin connector. If you don’t find
a coax cable and find a 6-pin connector
along with a 3-pin connector, your vehicle
doesn’t need this DSP kit.
NOTE: If your vehicle has Digital Signal
Processing (DSP), the purchase
of a RFIPOD-BMW-DSP kit may
be necessary..
5. Remove carpet and side cover to gain
access to CD Changer BUS harness.
If CD Changer is present, it will need
to be disconnected and/or removed.
IMPORTANT: Before connecting the interface harness, ensure that the 3 pin connector
on the vehicle harness does not have a brown wire in the middle
(pre-wire for phone). Proper connection is to a 3 pin connector with
the brown wire to the side (pre-wire for CD). Incorrect connection will
result in damage to the interface and not covered by warranty.
6. Locate both the 3-pin & 6-pin connectors in the trunk area. If the CD Changer is
present, disconnect the cables and set aside. If no CD Changer is present, the cables will
be bundled and tucked away in the rear trunk area.
IMPORTANT: Some vehicles will have the CD Changer harness in a protective sheath
which may make it more difficult to find.Vehicles sold outside the USA
may not be pre-wired.
7. Connect both 3-pin and 6-pin harnesses from the vehicle to the interface harness.
8. Fold down rear seats (if applicable) and route the interface harness to the rear seat
bottom cushion.
9. Remove bottom seat cushion by lifting up and route harness underneath.

6
Installation
10. Route the remainder of the interface harness in the best possible manner (e.g. under
the door sill or under the drivers seat) and connect it to the Vehicle connector on the
interface module.
NOTE: When routing harnesses or cables, ensure they are secured away from sharp
edges and moving parts by the use of cable ties.
11. Connect the iPod cable to the interface module and carefully route it to the location
where the iPod will be mounted (such as the glove box or center console).
12. Verify that all connections have been properly made.
13. Reconnect the vehicle battery, turn the ignition on and test the unit. Use the ‘Text
Display Settings’ proceedure below to make final adjustments before reinstalling any
panels/trim.
Text Display Settings
Make sure to select the appropriate text display setting during the initial setup of this kit.
To configure text display on BMW radios, press DISC 6 then select a Track number that
corresponds to the designated display from the chart below.
Operation
ConnectingYour iPod
Simply connect your iPod to the interface cable coming from the interface
module.The interface automatically charges the battery of the iPod when
connected and the key is in the ACC/ON position.The charging icon will
appear on the upper right corner of the iPod screen to indicate charging.
NOTE: We recommend disconnecting your iPod when not in use or when the vehicle is
turned off.
Charging Icon

7
Operation
iPod Hierarchy
By default, the interface creates a Playlist having a name that is the same
as the name of the iPod.This Playlist is the very first on the list of
Playlists shown while browsing in Playlist mode.This Playlist contains all
the songs on the iPod. Once a Playlist is active an Artist may be selected
within that Playlist using the Artist Mode. Albums by the selected Artist
and within the selected Playlist may be selected in Album Mode.
“ALL ARTIST” and “ALL ALBUM” designate all available content in
those categories.
Operating Controls
Press the MODE button to access the interface and its features. Pressing this button
repeatedly will cycle through sources present (internal CD if present, followed by external)
in your vehicle.When the iPod audio source is active (displayed as DISC 5,Track 1), use the
TRACK button to select next/previous song.
(Actual radio appearance may differ from that shown)
BMW business CD radio
(Actual radio appearance may differ from that shown)
BMW radio with Navigation
MODE
Source
Selector
MODE
Source
Selector
Buttons 1– 6
Press to
change DISC
Buttons 1– 6
Press to
change DISC
Source indicator TRACK
Press to change Track
Press and hold to RW (rewind)
or FFW (fast-forward)
NOTE: On some older BMW radios
the `m´ button must be pressed to
perform the same action.
TRACK
Press to change Track
Press and hold to
RW (rewind) or
FFW (fast-forward)
RND
Press to enable
Shuffle Song
Turn to
change Track
Jog Dial
NOTE: A 9 second timeout is engaged once any of the alternate display
buttons are pressed. If exiting from any of these sub-screens without
waiting for the normal timeout, you must wait 9 seconds before being
able to use the Jog Dial again to navigate content.
Playlist
Artist
Album
Song
More browsable content
Less browsable content

8
Operation
Mode Selection – Browsing
Interface Module set to ˝Radio˝
Once the iPod is connected and selected as the audio source, you can browse through
the modes by selecting the appropriate DISC button. Change Tracks within that mode
by pressing the TRACK button (depending on model, the Jog Dial can be rotated for this
function). One (1) second after releasing the button, your selection is executed. Browse
through the modes as shown;
NOTE: In DISC 5, you can select the audio source (iPod/AUX1) and in DISC 6, you can
set Text display (refer to Text Display Settings in ‘Installation’), and view firmware
version information.
Press TRACK
button
or
Rotate Jog Dial
to
select within
the modes

9
Auxiliary Audio Source
Connecting
The interface is equipped with a 1/8” AUX jack input to connect an auxiliary device, such as
an MP3 player, DVD player or other audio source.
NOTE: We recommend to only connect to the interface module when the vehicle ignition
is turned off.
Connect into the interface module from
your auxiliary device with a cable that
has a 1/8” mini stereo jack (not included).
Selecting AUX Input
To access the AUX audio source, select DISC 5, Track 2 or Preset 5, Channel 2 (depending
on the radio model).
AUX audio source settings
The auxiliary input has settings for Gain (volume), Bass, Mid and Treble for optimizing sound.
Gain (Volume) should be adjusted if the audio level from the auxiliary device is too low or
too high. If you hear distorted audio while playing the auxiliary device, you need to reduce (-)
the gain. If you notice that the audio is too quiet then the gain setting should be increased (+).
The default setting for gain is “68” and may be adjusted in increments between 01-99.
Bass, Mid and Treble default settings are “50” and can be adjusted between 01-99 to
compensate for the acoustic presets of the radio.
Making the adjustments
While listening to the auxiliary device, use the DISC or PRESET buttons (depending on the
radio model) to move between the settings as follows;
DISC (PRESET)-1 for Gain (Volume) DISC (PRESET)-2 for Bass EQ
DISC (PRESET)-3 for Mid EQ DISC (PRESET)-4 for Treble EQ
Then use the TUNE or SEEK button to adjust the setting (depending on the radio model
the TUNE knob can be rotated for this function).
NOTE: If you are using an auxiliary device that is using the vehicle’s power source and not its
own battery, you may have to use a GROUND-LOOP isolator to avoid engine and
grounding
noise.
1/8” AUX
connector Interface Module

10
Troubleshooting
Problem
Cannot select the interface.
Radio/NAV display only shows DISC
and Track number, but there is no iPod
control.
No audio from iPod source.
Radio/steering wheel controls do not
operate iPod.
Music is distorted or sound level is
too low.
No text displayed.
Correct DIP switch setting, but still no
text displayed.
iPod does not charge.
Solution
Check DIP switch settings (refer to
Pre-System Setup). With the ignition
OFF disconnect vehicle harness from
module for one (1) minute and reconnect.
Verify that the correct button is used to
access the interface.
Select DISC 5 and ensure it is set
to Track 01.
Reset the iPod.Verify proper connection
to iPod/interface.
Reset iPod and make sure most recent
iPod firmware is installed. Check vehicle
user manual on how steering wheel
controls work.
Check and make sure all EQ and BASS
boost options are turned off on your iPod
(refer to Auxiliary Audio Source).
Make sure DIP switch settings are
correctly set for text display (refer to
Pre-System Setup). Note: Early model
Mini Cooper vehicles do not support
text display.
Select DISC 6 to set text output to the
correct location (refer to Text Display
Settings in ‘Installation’).
Check all connections. Reset iPod and
make sure iPod charges while connected
to computer or wall charger.

11
Warranty
The Rockford Fosgate iPod Interface Module has a warranty of 1 Year.This warranty
covers only the original purchaser of Rockford product purchased from an Authorized
Rockford Fosgate Dealer in the United States. In order to receive service, the purchaser
must provide Rockford with a copy of the receipt stating the customer name, dealer name,
product purchased and date of purchase.
Products found to be defective during the warranty period will be repaired or replaced (with
a product deemed to be equivalent) at Rockford’s discretion.
What is Not Covered
1. Damage caused by accident, abuse, tampering, improper operations, water, direct sunlight,
excessive heat, theft, shipping.
2. Any cost or expense related to the removal or reinstallation of product.
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate
Service Center.
4. Any product which has had the serial number defaced, altered, or removed.
5. Subsequent damage to other components.
Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and merchantability are limited
in duration to the period of the express warranty set forth above. Some states do not allow
limitations on the length of an implied warranty, so this limitation may not apply. No person
is authorized to assume for Rockford Fosgate any other liability in connection with the sale
of the product.
How to Obtain Service
Contact the Authorized Rockford Fosgate Dealer you purchased this product from.
If you need further assistance, call 1-800-669-9899 for Rockford Customer Service.

12/08 B.M.
1230-55530-01 Printed in U.S.A
Rockford Fosgate
Rockford Corporation
600 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A., 480-967-3565
Customer Service 1-800-669-9899