Rockwell Automation Allen-Bradley 2080-LC20 User manual

Micro800 Controllers Starter Pack Quick Start
Catalog Numbers Bulletin 2080-LC20, 2080-LC30, 2080-LC50
Quick Start
Original Instructions

Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are
required to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may
be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from
the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Labels may also be on or inside the equipment to provide specific precautions.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous
environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

3Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 3
Where to Start
Follow this path to learn how to use the Connected Components Workbench™ software with your Micro800™ controllers
and PanelView™ 800 terminals.
Chapter 1
Study Guide Overview
Chapter 2
Hands On Content
Chapter 3
Create and Save a Connected
Components Workbench Project
Chapter 4
Build and Download Project
Chapter 5
Connect the Input Simulator Board
Chapter 6
Monitor Your Micro800 Controller
Chapter 7
How to Create Variables
Chapter 8
How to Implement an Instruction Block
Chapter 9
How to Add a Plug-in Module
Chapter 10
Learn About User-Defined Functions
(UDF) and User-Defined Function Blocks
(UDFB)
Chapter 11
Import and Export Project
Chapter 12
Quick Tips
Chapter 13
PanelView 800 HMI Design Using
Connected Components Workbench
Chapter 14
Using HMI Tags
Chapter 15
Configure Micro800 Controller
Ethernet Settings
Chapter 16
HMI Tag Editor
Chapter 17
HMI Screen
Chapter 18
Configure PanelView 800 Terminal
Ethernet Settings
Chapter 19
Download HMI Application
Chapter 20
Test the HMI Application

4 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017
Where to Start
Notes:

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 5
Table of Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preface About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1
Study Guide Overview
Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Start Connected Components Workbench Software . . . . . . . . . . . . . . . . 11
Connected Components Workbench Design Environment. . . . . . . . . . 12
Project Organizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Workspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 2
Hands On Content
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3
Create and Save a Connected
Components Workbench
Project
Create a Connected Components Workbench Project . . . . . . . . . . . . . . 19
Save Your Connected Components Workbench Project. . . . . . . . . . . . . 25
Chapter 4
Build and Download Project
Build and Download the Project to your Micro800 Controller . . . . . . . 27
Chapter 5
Connect the Input Simulator
Board
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Chapter 6
Monitor Your Micro800
Controller Program
Monitor Your Program in
Connected Components Workbench Software . . . . . . . . . . . . . . . . . . . . . 33
View Real-time Changes in List Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Chapter 7
How to Create Variables
Create Local Variables for your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 8
How to Implement an
Instruction Block
Add a TON Instruction Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Enter Parameters for TON Instruction Block. . . . . . . . . . . . . . . . . . . . . . . 41
Add an ANY_TO_TIME Instruction Block . . . . . . . . . . . . . . . . . . . . . . . 44

6Rockwell Automation Publication 2080-QS004B-EN-E - October 2017
Table of Contents
Chapter 9
How to Add a Plug-in Module
Add a Plug-in Module to the Micro800 Controller. . . . . . . . . . . . . . . . . . 49
Chapter 10
Learn About User-Defined
Functions (UDF) and
User-Defined Function Blocks
(UDFB)
Create a UDF for your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Add the UDF to your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Get Sample Code from the
Rockwell Automation Sample Code Library . . . . . . . . . . . . . . . . . . . . . . . . 59
Import Sample Code into Your Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 11
Import and Export Project
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Chapter 12
Quick Tips
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Chapter 13
PanelView 800 HMI Design
Using Connected Components
Workbench
Add a PanelView 800 Terminal to Your Project. . . . . . . . . . . . . . . . . . . . . 69
Configure Your PanelView 800 Terminal Communication Settings . . 70
Chapter 14
Using HMI Tags
Create Global Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Edit Ladder Diagram Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chapter 15
Configure Micro800 Controller
Ethernet Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Chapter 16
HMI Tag Editor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Chapter 17
HMI Screen
Create a Screen for Your PanelView 800 Application. . . . . . . . . . . . . . . . 83
Create Objects for Your Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Chapter 18
Configure PanelView 800
Terminal Ethernet Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Chapter 19
Download HMI Application
Save and Download Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 7
Table of Contents
Chapter 20
Test the HMI Application
Run the HMI Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Test the HMI application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Appendix A
Set Up Serial Communication
Between PC and Micro820
Controller
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Connect the PC to the Micro820 Controller . . . . . . . . . . . . . . . . . . . . . . 108
Configure RSLinx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Restore Serial Port to Factory Default Setting
Using MicroSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

8Rockwell Automation Publication 2080-QS004B-EN-E - October 2017
Table of Contents
Notes:

9Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 9
Preface
About This Publication
Use this quick start to learn how to use a Micro800 controller with a PanelView 800 terminal. You will use the Connected
Components Workbench software.
Additional Resources
These documents contain additional information concerning related products from Rockwell Automation.
You can view or download publications at
http:/www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local
Allen-Bradley distributor or Rockwell Automation sales representative.
Resource Description
Micro800 Controllers Starter Pack Quick Reference,
publication 2080-QR003 Provides information for setting up the Micro800 controllers and input simulator boards.
PanelView 800 HMI Terminals User Manual, publication
2711R-UM001 Information in setting up and using the PanelView 800 terminals, and installing
the Connected Components Workbench software.
Micro820 20-point Programmable Controllers User
Manual, publication 2080-UM005 Information on setting up and using the Micro820™ controllers.
Micro830 and Micro 850 Programmable Controllers
User Manual, publication 2080-UM002 Information on setting up and using the Micro830®and Micro850®controllers.
Connected Components Workbench Software Website
http://www.rockwellautomation.com/global/support/c
onnected-components/workbench.page
Provides product information on Connected Components Workbench software
and links to download the software.
Connected Components Workbench Online Help Online Help that provides a description of the different elements of the
Connected Components Workbench software.

10 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017
Preface
Notes: