ROCTEST PISA-M User manual

INSTRUCTION MANUAL
MEMS VERTICAL IPI SERIAL SENSORS
Model PISA-M
Roctest Limited, 2016. All rights reserved.
This product should be installed and operated only by qualified personnel. Its misuse is potentially dangerous. The Company makes no warranty as to the information furnished
in this manual and assumes no liability for damages resulting from the installation or use of this product. The information herein is subject to change without notification.
Tel.: [phone] • 1.877.ROCTEST (Canada, USA) • 33.1.64.06.40.80 (France) • 41.91.610.1800 (Switzerland)
www.roctest.com
E10350-161101

i
TABLE OF CONTENTS
1INTRODUCTION......................................................................................................1
1.1 VERTICAL IN-PLACE INCLINOMETERS.........................................................1
1.2 SENSOR COMPONENTS ................................................................................1
1.3 SERIAL SENSOR CABLE CONNECTIONS......................................................3
1.4 OTHER COMPONENTS...................................................................................4
1.5 SUSPENSION KITS..........................................................................................4
2PREPARATION FOR INSTALLATION....................................................................5
2.1 CHECK SENSORS...........................................................................................5
2.2 PREPARE SUSPENSION CABLE....................................................................5
2.3 ATTACH GAUGE TUBING ...............................................................................6
2.4 GATHER TOOLS..............................................................................................6
3INSTALLATION.......................................................................................................7
3.1 INSTALLATION OVERVIEW.............................................................................7
3.2 gather tools.......................................................................................................7
3.3 INSTALL THE FIRST SENSOR........................................................................7
3.4 INSTALL ADDITIONAL SENSORS...................................................................8
3.5 INSTALL THE TOP WHEEL..............................................................................9
3.6 SUSPEND THE SENSORS ..............................................................................9
3.7 NOTE ON RETRIEVING SENSORS.................................................................9
4DATA REDUCTION...............................................................................................10
4.1 INTRODUCTION.............................................................................................10
4.2 CALIBRATION SHEET ...................................................................................10
4.3CONVERTING VOLTS TO TILT .....................................................................10
4.4 CALCULATING TILT IN MM/M .......................................................................10
4.5 CALCULATING TILT IN DEGREES................................................................11
4.6 CALCULATING DEVIATION...........................................................................11
4.7 CALCULATING DISPLACEMENT...................................................................11
4.8 DIRECTION OF TILT AND DISPLACEMENT .................................................11
5CONNECTION TO DATALOGGERS.....................................................................12
5.1 Campbell Scientific CR6..................................................................................12

ii
5.2 WIRING DIAGRAM.........................................................................................13
5.3 LIMITATIONS .................................................................................................14

E10350-161101 IPI
Page 1
1 INTRODUCTION
1.1 VERTICAL IN-PLACE INCLINOMETERS
The in-place inclinometer system consists of the inclinometer casing and a string of in-
place inclinometer sensors (please see Figure 2 on next page).
The inclinometer casing provides access for subsurface measurements, controls the
orientation of the sensors, and moves with the surrounding ground.
In vertical installations, the casing is installed in a borehole that passes through a
suspected zone of movement into stable ground below. One set of grooves in the casing
is aligned with the expected direction of movement, as shown below.
Figure 1
Casing should be installed with one set of grooves aligned with the expected direction of
movement. The wheels of the sensors are inserted in these grooves.
The grooves in the casing control the orientation of the in-place inclinometer sensors. A
stainless steel cable keeps the sensors at the required depth.
The sensors measure inclination from vertical. As ground movement occurs, the casing
moves with it, changing the inclination of the sensors inside the casing.
The inclination measurements are then processed to provide displacement readings in
mm or inches.
In most applications, sensors are connected to a data acquisition system and data
processing is completed by a computer program.
1.2 SENSOR COMPONENTS
In-place sensors can be installed as a single sensor or as a string of linked sensors.
Figure 3 shows both.

E10350-161101 IPI
Page 2
An individual sensor includes a sensor body, a gauge tube, a top wheel, and a bottom
wheel.
A string of linked sensors includes nsensor bodies, ngauge tubes, a top wheel, a
bottom wheel, and n-1 middle wheels.
Sensor bodies can contain uniaxial or biaxial sensors, both look the same.
Gauge tubes are sized to make gauge lengths of 1, 2, or 3 m when joined to a sensor
Figure 2
Figure 3

E10350-161101 IPI
Page 3
body and wheels.
Top wheels have an eyelet for attaching a stainless steel suspension cable. They also
have a socket for connecting to a gauge tube.
Bottom wheels attach directly to the bottom of the sensor. They have no socket.
Middle wheels are used to link sensors. The middle wheel attaches directly to the
bottom of the sensor and has a socket for connecting to the gauge tube from the sensor
below.
1.3 SERIAL SENSOR CABLE CONNECTIONS
Figure 4

E10350-161101 IPI
Page 4
1.4 OTHER COMPONENTS
Figure 5
1.5 SUSPENSION KITS
Top suspension kit is used to suspend the IPI sensors from the top of the casing, as
shown on Figure 6. Stainless steel cable is ordered separately.
In-line suspension kit is used to suspend a string of deeper sensors from a string of
shallower sensors. This allows economical monitoring of two or more separate zones of
interest. Please refer to Figure 6.
Safety cable (not shown) is sometimes attached to the bottom sensor and used to
prevent loss of sensors downhole during installation. A safety cable is also helpful when
sensors are withdrawn from the casing.

E10350-161101 IPI
Page 5
Figure 6
2 PREPARATION FOR INSTALLATION
2.1 CHECK SENSORS
1. Check each sensor.
2. Identify the bottom sensor for each string. The bottom sensor will require a plug
for the bottom connector.
3. Make a note of the serial number of each sensor and its intended depth of
installation.
4. Mark sensors for order of installation.
5. Check length of jumper cable to make sure it will run from the top sensor to the
datalogger.
2.2 PREPARE SUSPENSION CABLE
1. Check project specifications for intended depth of top sensor.
2. Determine the required depth of the top wheels of the top sensor.

E10350-161101 IPI
Page 6
3. Determine the distance between the top wheels and the top of the casing. Cut
the stainless steel suspension cable to this length.
4. Connect suspension cable to top wheel as shown in Figure 7.
5. Connect suspension cable to the chain as shown in Figure 7.
Figure 7
2.3 ATTACH GAUGE TUBING
1. Remove screw from socket.
2. Align hole in gauge tube with hole in socket, then insert gauge tube into socket.
3. Insert screw and tighten to secure the gauge tube.
4. No further pre-assembly is recommended.
Figure 8
2.4 GATHER TOOLS
Vise-grips (clamping pliers) for holding gauge tubing while connecting adjacent
sensors.
Allen wrench for screws that secure gauge tubing.
Cable ties or vinyl tape to secure cable gauge tubing.
Optional: safety cable connected to bottom sensor to prevent loss of sensors
down hole. The safety cable is also helpful when the sensors are withdrawn from
the casing.

E10350-161101 IPI
Page 7
3 INSTALLATION
3.1 INSTALLATION OVERVIEW
1. Lay out sensors in the order of installation.
2. Insert the first sensor into the preferred set of grooves.
3. Lower the sensor into the casing. Using the vise-grip, clamp the top of the gauge
tube to hold the sensor while you connect the next sensor.
4. Align the next sensor with the preferred set of grooves as in step 2, and connect
it to the gauge tubing of the downhole sensor.
5. Lower the two sensors. Repeat steps 4 and 5 until all sensors have been
installed.
6. Connect the top wheel and suspension kit and lower the sensors to their final
elevation.
3.2 GATHER TOOLS
1. Vice grips (Clamping pliers) for holding gauge tubing while connecting adjacent
sensors.
2. Allen wrench for screws that securing gauge tubing.
3. Cable ties or vinyl tape to secure cable to gauge tubing.
4. Optional: safety cable connected to bottom sensor to prevent loss of sensors
down hole. The safety cable is also helpful when the sensors are withdrawn from
the casing.
3.3 INSTALL THE FIRST SENSOR
1. Check that bottom connector of first sensor is capped.
2. Optional: Attach safety cable to wheel assembly.
3. Insert first sensor in selected set of grooves. The fixed wheel should point to the
expected direction of movement, as shown on Figure 9.
4. Secure signal cable to gauge tubing and then lower sensor into casing. Clamp
the top of gauge tubing to hold it at the top of the casing.

E10350-161101 IPI
Page 8
Figure 9
3.4 INSTALL ADDITIONAL SENSORS
1. Connect next sensor to the gauge tubing of the sensor below. Always check that
fixed wheel points to expected direction of movement, as shown on Figure 10
2. Check that connectors are clean, and then connect the cables. Secure excess
cable to the gauge tubing with tape or a cable ties.
3. Continue adding sensors until the sensor string is complete.
Figure 10

E10350-161101 IPI
Page 9
3.5 INSTALL THE TOP WHEEL
1. Connect the data cable to top sensor. Cable runs from top sensor to data logger
(see Figure 11).
2. Connect top wheel to gauge tube.
Figure 11
3.6 SUSPEND THE SENSORS
1. Check that suspension cable is securely clamped.
2. Use the chain and S-hook to make fine adjustments to the final depth of the
sensor (see Figure 12).
Figure 12
3.7 NOTE ON RETRIEVING SENSORS
Withdraw the sensors one by one rather than trying to pull out the entire chain. If you try
to extract the entire chain at once, you will bend the gauge tubes and the wheels.
1. Draw each sensor upwards.
2. Clamp the gauge tube of the sensor below.
3. Disconnect the sensor, and repeat. If you intend to reinstall the sensors, check
that they are still numbered for order of installation.

E10350-161101 IPI
Page 10
4 DATA REDUCTION
4.1 INTRODUCTION
Data reduction is usually automated because it involves a large number of readings and
a large number of calculations.
In this section, we explain the sensor calibration sheet and provide an example of
converting a single reading in volts to tilt in mm per meter and tilt in degrees.
4.2 CALIBRATION SHEET
A calibration sheet is provided with each sensor. Use sensor serial numbers to match
sensors with their calibrations. Calibrations are unique for each sensor.
Factors for tilt are C0, C1, C2, C3, C4 and C5. A-axis factors have an A prefix: AC0,
AC1, AC2, AC3, AC4, AC5 and B-axis factors have a B prefix.
4.3 CONVERTING VOLTS TO TILT
To convert a reading in volts to tilt, use the following formula.
Tilt (mm/m)=C5*Volts2+C4*Volts+C3+C2*TdegC+C1*TdegC2+C0*Volts*TdegC
Where
C5…C0 are factors for A-axis or B-axis
Volts is the sensor reading in volts
TdegC is the temperature reading in degrees Centigrade
4.4 CALCULATING TILT IN MM/M
For example, Sensor 14384 gives an A-axis reading of 0.4137 V at 6.7°C. The
calibration sheet lists these factors for tilt in mm/m:
AC5 = -3.3789E-3
AC4 = 7.9648E1
AC3 = 5.4138
AC2 = -2.9838E-2
AC1 = -2.5159E-4
AC0 = 9.8415E-3
Tilt=C5*Volts2+C4*Volts+C3+C2*TdegC+C1*TdegC2+C0*Volts*TdegC
Tilt = 38.1797 mm/m

E10350-161101 IPI
Page 11
4.5 CALCULATING TILT IN DEGREES
For example, Sensor 14384 gives an A-axis reading of 0.4137 V at 6.7°C. Then to
convert the tilt in mm/m in degree, following formula must be applied.
Tilt (degrees) = arcsin(Tiltmm/m /1000)
With previous reading
Tilt (degrees) = arcsin(38.1797/1000)
Tilt = 2.188°
4.6 CALCULATING DEVIATION
To calculate deviation over the gauge length of the sensor, use either formula below:
Deviationmm = Tiltmm/m * gauge_lengthm
or
Deviationmm = sin(Tiltdeg) * gauge_lengthmm
For example, Sensor 14384 has a gauge length of 2 meters. The examples below use
the temperature corrected tilt values.
Deviationmm = 38.1797 mm/m * 2 m
Deviationmm = 76.3594
Deviationmm = sin(2.188) * 2000 mm
Deviationmm = 76.357
4.7 CALCULATING DISPLACEMENT
Displacement (movement) is the change in deviation:
Displacement = Deviationcurrent - Deviationinitial
4.8 DIRECTION OF TILT AND DISPLACEMENT
Uniaxial sensors respond to tilt in the plane parallel to the wheels of the sensor. This
plane is called the A axis. A-axis readings may be positive or negative. Positive readings
indicate that the sensor is tilted in the direction of the fixed wheel. Negative readings
indicate that the sensor is tilted in the direction of the sprung wheel. Please refer to
Figure 13.
Biaxial sensors respond to tilt in the plane of the wheels (A-axis) and the plane rotated

E10350-161101 IPI
Page 12
90 degrees to the wheels (B-axis). Positive A-axis readings show tilt in the direction of
the fixed wheels. Positive B-axis readings show tilt in the direction rotated 90 degrees
clockwise. Displacement directions follow the same convention. In the Figure 14, the
sensor is viewed from the top.
Figure 13
Figure 14
5 CONNECTION TO DATALOGGERS
5.1CAMPBELL SCIENTIFIC CR6
These instructions provide information needed for reading uniaxial and biaxial Pisa-M
with the Campbell Scientific CR6 datalogger system.
Wiring diagrams: The wiring diagram below shows how to connect serial Pisa-M to the
Campbell Scientific CR6 datalogger. Uniaxial and biaxial connections are identical.
B+
B-
A+ (Fixed wheel)
A- (Sprung wheel)

E10350-161101 IPI
Page 13
5.2WIRING DIAGRAM
Figure 15

E10350-161101 IPI
Page 14
5.3LIMITATIONS
The list below shows nominal limits for chain of serial sensors. The following table
assumes that the logger supplies 12 volts:
Cable Length of jumper cable
Limit of sensors in the chain
40 m
50 sensors
92 m
40 sensors
165 m
30 sensors
258 m
20 sensors
375 m
10 sensors