RocwooD RS600 User manual

RS600
ELECTRIC PRESSURE WASHER
INSTRUCTION MANUAL
PLEASE RETAIN
DO NOT USE APPLIANCE WITHOUT
READING THIS FIRST

IMPORTANT SAFETY INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be grounded. In case it should malfunction or breakdown, grounding provides a
path of least resistance for electrical current to reduce the risk of electric shock. This product is
equipped with a cable with a grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is professionally installed and grounded in accordance with
all local codes and ordinances. DANGER - Improper connection of the grounding conductor can
result in a risk of electrocution. Check with a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the
product. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Do not
use any type of adapter with this product.
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground-fault circuit-interrupter (GFCI) built into the plug of
the power-supply cable. This device provides additional protection from the risk of electric shock.
Should replacement of the plug or cable become necessary, use only identical replacement parts
that include GFCI protection.
WARNING: When using this product, basic precautions should always be followed, including the
following:
1.
Read all the instructions before using the product.
2.
To reduce the risk of injury, close supervision is necessary when using this product near
children.
3.
Know how to stop the product and bleed pressure quickly. Be thoroughly familiar with the
controls.
4.
Stay alert - watch what you are doing.
5.
Do not operate the product when fatigued or under the influence of alcohol or drugs.
6.
Keep operating area clear of all persons.
7.
Do not overreach or stand on unstable ground. Always keep a good footing and balance.
8.
Follow the maintenance instructions specified in the manual.
9.
This product is provided with a ground fault circuit interrupter built into the power cable plug. If
replacement of the plug or cable is needed, use only identical replacement parts.
10.
WARNING: The temperature of the inlet water must not exceed 40 degrees.
11.
WARNING: Risk of Injection or Injury - Do Not discharge stream at people or animals.

EXTENSION CABLES
Use only 3-wire extension cables that have 3-prong grounding-type plugs and 3-pole cable
connectors that accept the plug from the product.
Use only extension cables that are intended for outdoor use. These extension cables are
identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in
use.”
Use only extension cables having an electrical rating not less than the rating of the product.
Do not use damaged extension cables.
Examine extension cable before using and replace if damaged.
Do not abuse extension cable and do not pull on any cable to disconnect.
Keep cable away from heat and sharp edges.
Always disconnect the extension cable from the receptacle before disconnecting the product
from the extension cable.
WARNING - To reduce the risk of electrocution, keep all connections dry and off the ground.
Do not touch plug with wet hands.
PREPARATION
1. On unpacking the unit, you discover damage has been caused during transportation, please
contact your dealer.
2.
Check to make sure that the packing list and the information paper are correct.
3.
Check whether the voltage shown on the rating plate corresponds to that of the power source:
voltage 220-240VAC, the current carrying capacity of the circuit should not be less than 10A.
INSTALLATION INSTRUCTIONS
1.
Make sure that the pressure washer is switched off and disconnected from the mains supply.
2.
Connect the pressure hose and trigger assembly.
3.
Locate the filter inside the water inlet.
4.
The inlet filter must always be fitted inside the water inlet to filter out sand, limestone, and
other
impurities as they will damage the pump valves. Caution: failing to fit the filter will invalidate
the
guarantee.
5.
Connect the water supply hose to the connector. The water supply hose is not provided in the
packaging.

OPERATING INSTRUCTIONS
STORAGE INSTRUCTIONS
1.Connect one side of the inlet hose with inlet nipple to the machine, another side to the
water tap, tighten with a clamp. (Note: there is a sealing ring inside nut, do not lose.)
2.Eye protection is advised.
3.Connect the water supply and the power source, turn the water supply on, making sure
that the tap is fully open. Then turn on the power switch of the machine-and the-gun
trigger, exhaust any air in the machine by squeezing the trigger. The unit is then ready for
operation.
4.The lance has an adjustable nozzle to allow you to vary the width of the spray. To
adjust the width of the spray, rotate the nozzle.
5.If using a water tank, the water level in the tank should not be lower than the machine
itself, and the inlet hose must be fitted with a filter and primed with water.
6.During cleaning, the distance between the nozzle and the object surface to be cleaned
should not be more than 30cm, as the impulsive force decreases with the increase of
distance.
7.You should hold the gun trigger firmly during cleaning.
8.The safety catch does not control the gun during operation, it only prevents it from
opening unintentionally.
9.Do not direct the spray at human beings or electric equipment.
10.Be careful where the power cable is placed so that it does not get damaged.
11.After the cleaning is finished, release the trigger, switch off the machine and unplug
the power cable from the mains. Close the water inlet and detach the appliance from the
water connection. Depress the trigger to release the pressure in the appliance and secure
the trigger with the safety button to prevent unintentional use.
USER MAINTENANCE INSTRUCTIONS
Monthly or as required, to maintain the appliance.
1.To clean the nozzle. Make sure the machine is disconnected from the power & any residual
pressure is released by squeezing the trigger, then remove the dirt from the nozzle hole with a
needle and rinse it with water.
2.Clean the strainer in the water connection. It can be easily removed with flat-nosed pliers.
Winter protection
Frost will destroy an appliance that has not been completely emptied of water. The correct
storage method is to separate the inlet hose from the water supply system. Turn on the machine
to run for about 30 seconds for water extraction then remove the high-pressure plastic hose to
remove the remaining water in it. The appliance is best stored in a warm room.

TECHNICAL CHARACTERISTICS
ELECTRIC SUPPLY AND MAINS WATER SUPPLY
Model
Rated voltage
Power
Protection degree
Max. input water
temperature
Max. input water
pressure
Cleaning solution
Hose Length
RS600
240V/ 50HZ
2000W
IPX5
40
0.6MPa
Household
detergent
10m
PERFORMANCE
Rated pressure 10MPa (100 BAR)
Rated ow 360 L/H
ACCESSORIES
1. GUN
2. WAND
3. MALE CONNECTOR
4. CLEANING PIN
5. INTEGRATED DETERGENT TANK
6. PATIO CLEANER
7. ROTARY BRUSH
8. FIXED BRUSH

PROBLEM SOLVING
Causes Solution
Problem
Appliance does
not work.
1. No power,
or condition in
the socket is not good.
2. The
connector
cable
is
damaged.
1. Check the power source
and the socket to see if the
plug is connected.
2. Change the cable.
Appliance does not
reach operational
pressure.
1. The
double
nozzle
is
worn out.
2. Air exists in the hose.
3. The
inlet
hose
leaks
or
is
blocked.
4. The inlet or outlet valve
is damaged.
5. The
sealed
ring
of
the
plunger is damaged.
6. The O-ring of the unload
valve is damaged.
7. Pump seat leaks.
1. Change
the
double
nozzle.
2. Start
the
motor,
turn
on
the
spray
nozzle
and
ll
the inlet hose with water to
exhaust air.
3. Clean
or
change
the
inlet hose.
4. Change the valves.
5. Change the sealed ring.
6. Change the O-ring.
7. change the pump seat.
The pump leaks.
1. The sealed ring is
damaged.
2. The bolt works loose.
1. Change the sealed ring.
2. Tighten the bolt.
No water ows or
ow rate too low.
1. The
new
pump
does not
take in water.
2. Dirt exists in the pump.
3. The inlet or outlet valve
is damaged.
1. Switch on, and open the
gun
trigger
valve,
then
fill
water into the inlet hose so
to exhaust air, place the
inlet hose into water tank.
2. Remove the dirt.
3. Change the valve.
If any problems are encountered that are not covered above, please refer to qualied service
personnel.
Table of contents
Other RocwooD Pressure Washer manuals
Popular Pressure Washer manuals by other brands

Kärcher
Kärcher G 2500 VH Operator's manual

Champion Power Equipment
Champion Power Equipment 76520 Owner's manual & operating instructions

Alto
Alto POSEIDON 5 DRIFTSVEJLEDNING

Craftsman
Craftsman 919.769063 owner's manual

Campbell Hausfeld
Campbell Hausfeld PW2220 product manual

Husky
Husky HU80522 Operator's manual