RODE Microphones NT1000 User manual

(EMC, LVD)
NT1000
Instruction Manual
www.rodemic.com

- 2 -
Introduction
I want to thank you for your purchase of the
NT1000 large diaphragm microphone.
With its ultra low 6 dBA self-noise and transformer less
SMT circuitry, the RØDE NT1000 exhibits exceptional
performance when recording both vocals and
instruments in the studio.
Voiced for ‘application versatility’, the NT1000 has been
hailed by many as the ultimate drum over-head and
grand piano mic selection.
The NT1000 is also equally at home as a first call
vocal mic. With its Australian made 1” HF-2 capsule
incorporating internal shock mounting, the NT1000
boasts a 134 dB dynamic range and 140 dBA SPL
capabilities as well as a 20 Hz - 20 kHz frequency
response.
Please take the time to visit www.rodemic.com and
register your microphone for a full ten year warranty.
While there you can view studio tips and techniques, as
well as browse the comprehensive range of accessories
for the NT1000 and other microphones.
Peter Freedman
Microphones
Sydney, Australia

- 3 -
Specifications
Acoustic
Principle:
Pressure gradient
Active
Electronics:
Unity-gain closed-loop
impedance converter; JFET
input with bipolar buffering
Directional
Pattern:
Cardioid
(see graph)
Frequency
Range:
20Hz ~ 20,000Hz
(see graph)
Output
Impedence:
100Ω
Sensitivity: -36dB re 1V/Pa @ 1kHz
(16mV @ 94dB SPL)
±1dB @ 1kHz
Equivalent Noise: 6dBA SPL
(per IEC651)
Maximum
Output:
+13 dBu
(@ 1kHz, 1% THD into 1kΩ)
Dynamic Range: >134dB (per IEC651)
Maximum SPL: >14 0 d B
(@ 1kHz, 1% THD into 1kΩ)
Signal/Noise: >88dB SPL
(@ 1kHz, rel 1Pa per IEC651)
Power
Requirement:
6mA @ Phantom P48
2mA @ Phantom P24
Output
Connection:
3-pin XLR, , balanced output
between pin 2 (+), 3 (-)
and pin 1 (ground)
Net Weight: 682g

- 4 -
Specifications
Frequency Response
Polar Response
Accessories
`ÊÀiÊ£Ê6É*>
ÊÓä
棊
Êä
Ê £ä
Ê Óä
Ê Îä
ÊÓäâÊ £ääÊ £äääÊ £äÊäääÊ ÓäÊäää
äÂ
ä ÓÇ
ä
£näÂ
Ó°ä
Óä°ä
Ê£ä°äÊÊ
ä°ä
Ó°ä
{°ä
È°ä
n°ä
£ä°ä
£Ó°ä
£{°ä
£È°ä
£n°ä
Óä°ä
ÓÓ°ä
Ó{°ä Óx°ä
`ÊÀi°Ê£6É*>
³x°ä
ÀiµÕiVÞ\
Ê xääÊâ\
£äääÊâ\
{äääÊâ\
–
–
–
RM2 Stand Mount
SM2 Shock Mount
(optional)
WS2 Windshield
(optional)
ZP1 Zip pouch

- 5 -
Features
• HF2 1” capsule with gold-plated diaphragm
• Ultra low noise transformerless circuitry
• Cardioid polar pattern
• Durable satin nickel finish
• High strength welded and heat-treated mesh head
• Internal capsule shock mounting
• True externally biased condenser
• Full frequency response
• Designed & manufactured in Australia
• Full 10 year guarantee*
Using the NT1000
• The NT1000 requires a power supply which for
optimum results should be a ‘P48’ standard,
48 Volt DC Supply.
Most professional mixing consoles have an internal
48 V supply; alternatively you can purchase a
separate supply. Ensure that the power supply you
use is a professional unit that is operating correctly.
Damage due to connection of the NT1000 to a
faulty power supply is not covered by the warranty.
• The NT1000 comes complete with a microphone
stand-mount (RM2). This should be used to attach
the microphone to a good quality stand.
*Online product registration required.

- 6 -
The stand-mount includes a thread adaptor
allowing connection to either 3/8” or 5/8”
stand thread.
• Always use a high quality microphone cable and
ensure that it is wired Pin 1 screen, Pin 2 (+), Pin 3 (-).
• We recommend that any connections made to the
mixer or recorder are made with the attenuation
(gain) set to OFF.
• When first switching the mixer on and phantom
power has been applied to the NT1000 you should
allow several seconds for the microphone to
stabilize.
• To ensure the lowest noise/distortion your mixer
input gain control should be set so that the Peak
Program Indicator (PPI) LED flashes ON during
peaks of the source (voice/instrument).
If there is no PPI, adjust the input gain while
listening for distortion of the sound. If distortion is
heard, gradually reduce the gain until it is no longer
present.
• Microphone technique, or how to get the sound
you want, requires experimentation.
We suggest that you start with the channel EQ
set to ‘OFF’ or ‘FLAT’ (no boost or cut). Try to get
the sound you want by placing either reflective or
absorbent panels at various angles adjacent to the
source being recorded.
Using the NT1000

- 7 -
• Changing the acoustic properties of the space
around the microphone is our recommended initial
approach for obtaining best sound quality.
Remember you cannot change a room’s acoustic
properties with EQ.
When the preferred sound has been achieved
(as above) then EQ and effects such as reverb
or indeed any signal processing can be used for
enhancement, but should be used sparingly.
Using the NT1000
• After use, the NT1000 should be removed from its
stand or shock mount, wiped with a dry, soft cloth
and placed in its protective zip pouch or case with
the supplied moisture-absorbent crystals.
• Be sure to place the moisture-absorbent crystals
(supplied) at the head of the microphone, so as to
absorb any moisture present.
Eventually this pack of crystals will need to be
dried. This is indicated by the crystals turning pink
in colour.
They can easily be re-used by placing them in an
oven at 100 - 150 degrees celsius for approximately
ten minutes. The crystals will operate effectively
again once they have turned blue.
Storage

- 8 -
Warranty
All microphones are warranted for one year
from date of purchase. You can extend that to a full
ten years if you register online at www.rodemic.com.
The warranty covers parts and labour that may be
required to repair the microphone during the warranty
period. The warranty excludes defects caused by
normal wear and tear, modification, shipping damage,
or failure to use the microphone as per the instruction
guide.
If you experience any problem, or have any questions
regarding your microphone, first contact the
dealer who sold it to you. If the microphone requires a
factory authorised service, return will be organised by
that dealer.
We have an extensive distributor/dealer network, but
if you have difficulty getting the advice or assistance
you require, do not hesitate to contact us directly.
Microphones
International
PO Box 6685
Silverwater NSW 2128 Australia
Ph: [phone]
Fax: [phone]
USA
P.O. Box 4189
Santa Barbara, CA 93140-4189
Ph: 805 566 7777
Fax: [phone]
Technical Support
For information and technical support questions contact:
[e-mail]
In the Unites States and Puerto Rico, contact
[e-mail] or call 805 566 7777
In Australia, contact [e-mail] or call [phone]
Anywhere except Australia, the United States and Puerto Rico,
contact [e-mail] or call [phone]