Roger ME-14-40VA User manual

Roger Access Control System
ME-14-40VA metal enclosure User Manual
Product version: 1.0
Document version: Rev. A

ME-14-40VA User manual.doc 2017-10-04
2/4
DESIGN AND APPLICATION
ME-14-40VA metal enclosure is dedicated to installation of RACS 5 modules and devices which require DIN
rail and 7Ah backup battery. The enclosure is equipped with DIN rail, 18VAC/40VA transformer and tamper
contact. The enclosure front panel is attached with screws. ME-14 is made of white powder coated stainless
metal sheet.
INSTALLATION
1. The enclosure must be installed indoors ensuring nominal environmental conditions as stated in the
Specification section.
2. All installation and maintenance works must be done with 230VAC power supply disconnected.
3. Power supply must be ensured with three wire cable including green-yellow PE.
4. Mains power supply cable must be fed into the enclosure through hole B.
5. L and N cable wires must be connected to L and N terminals of the transformer while green-yellow PE
wire must be connected to terminal C of the enclosure.
6. H connector must be connected to enclosure door.
7. The transformer in the enclosure is dedicated to continuous operation and is not equipped with on/off
switch. Therefore it is necessary to ensure overload protection in power supply circuit e.g. by applying
and indicating dedicated fuse in fuse box.
8. The user of system must be acquainted with power disconnection rules and conditions.
9. Transformer’s 18VAC power output must be connected to AC terminals of supplied device using
included cables.
10. Other connections must be done in accordance with manuals of installed devices.
11. Connection cables for installed devices must be fed into enclosure through hole D.
12. Starting, configuration and adjustments must be done in accordance with system procedures after
connection of 230VAC power supply.
13. Close the enclosure when installation and starting works are finished.
Caution
The installation can be done only by qualified person with all necessary
certificates concerning connection and maintenance of 230VAC and low
voltage networks.
Caution
It is forbidden to use the enclosure without properly executed and
operational earthing system.
Caution
Earthing system must be executed carefully, properly and effectively.
It is forbidden to use transformer without properly executed electric shock
protection.

ME-14-40VA User manual.doc 2017-10-04
3/4
Fig. 1 Arrangement of ME-14-40VA internal components
SPECIFICATION
Parameter
Value
TRP 40 transformer
16/18VAC; 40VA
Transformer standard
EN 61558-2-6
Tamper contact
NO/NC; 50mA/50VDC
DIN rail
1 x 250mm
Metal sheet
DC01; 0,7mm; anti-corrosion protection
Colour
RAL9003
Battery
Space for 7Ah battery
Environmental conditions
Indoor general conditions, relative humidity up to 90%;
temperature -10°C to +40°C
IP code
IP20
Internal dimensions (H x W x D)
250 x 250 x 80mm
External dimensions (H x W x D)
255 x 255 x 90 mm
Weight
2,7 kg

ME-14-40VA User manual.doc 2017-10-04
4/4
ORDERING INFORMATION
Product
Description
ME-14-40VA
Metal enclosure with 18VAC/40VA transformer
PRODUCT HISTORY
Product version
Date
Description
ME-14-40VA v1.0
07/2017
The first commercial version of the product
This symbol placed on a product or packaging indicates that the product
should not be disposed of with other wastes as this may have a negative
impact on the environment and health. The user is obliged to deliver
equipment to the designated collection points of electric and electronic
waste. For detailed information on recycling, contact your local authorities,
waste disposal company or point of purchase. Separate collection and
recycling of this type of waste contributes to the protection of the natural
resources and is safe to health and the environment. Weight of the
equipment is specified in the document.
Contact:
Roger sp. z o.o. sp.k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [e-mail]
Web: www.roger.pl