Roger ME-15 User manual
Roger Access Control System
ME-15 metal enclosure User Manual
Product version: 1.2
Document version: Rev. B
ME-15 User Manual.doc 2019-05-30
2/4
DESIGN AND APPLICATION
ME-15 metal enclosure is dedicated to installation of RACS 5 modules and devices which require DIN rail
and 7Ah backup battery. The enclosure is equipped with DIN rail, tamper contact and mounting bracket for
PS2D/PS4D/PS8D (Roger) power supply units. The enclosure front panel is attached with screws. ME-15 is
made of white powder coated stainless metal sheet.
INSTALLATION
1. The enclosure must be installed indoors ensuring nominal environmental conditions as stated in the
Specification section.
2. All installation and maintenance works must be done with 230VAC power supply disconnected.
3. Power supply must be ensured with three wire cable including green-yellow PE.
4. Insert mains power supply cable into enclosure through hole B.
5. Attach the power supply unit to the bracket E using included screws.
6. L and N cable wires must be connected to adequate terminals of the PSU while green-yellow PE wire
must be connected to terminal block A in the enclosure.
7. Terminal block A must be connected to PSU’s terminal with symbol.
8. F connector must be connected to enclosure door.
9. The PSU in the enclosure is dedicated to continuous operation and is not equipped with on/off switch.
Therefore it is necessary to ensure overload protection in power supply circuit e.g. by applying and
indicating dedicated fuse in fuse box.
10. The user of system must be acquainted with power disconnection rules and conditions.
11. PSU DC power output must be connected to adequate terminals of supplied device using included
cables.
12. Other connections must be done in accordance with manuals of installed devices.
13. Connection cables for installed devices must be fed into enclosure through hole C.
14. Starting, configuration and adjustments must be done in accordance with system procedures after
connection of 230VAC power supply.
15. Close the enclosure when installation and starting works are finished.
Caution
The installation can be done only by qualified person with all necessary
certificates concerning connection and maintenance of 230VAC and low
voltage networks.
Caution
It is forbidden to use the enclosure without properly executed and
operational earthing system.
Caution
Earthing system must be executed carefully, properly and effectively.
It is forbidden to use the PSU without properly executed electric shock
protection.
ME-15 User Manual.doc 2019-05-30
3/4
Fig. 1 Arrangement of ME-15 internal components
SPECIFICATION
Parameter
Value
Tamper contact
NO/NC; 50mA/50VDC
DIN rail
1 x 250mm
Metal sheet
DC01; 0,7mm; anti-corrosion protection
Colour
RAL9003
Battery
Space for 7Ah battery
PSU
Mounting bracket for PS2D, PS4D, PS8D power supply unit
Environmental conditions
Indoor general conditions, relative humidity up to 90%;
temperature -10°C to +40°C
IP code
IP20
Internal dimensions (H x W x D)
290 x 280 x 80mm
External dimensions (H x W x D)
295 x 285 x 90 mm
Weight
2,6 kg
ME-15 User Manual.doc 2019-05-30
4/4
ORDERING INFORMATION
Product
Description
ME-15
Metal enclosure
PS2D
Power supply unit 13.8VDC/2.5A
PS4D
Power supply unit 13.8VDC/5.4A
PS8D
Power supply unit 13.8VDC/10.8A
PRODUCT HISTORY
Product version
Date
Description
ME-15 v1.0
08/2017
The first commercial version of the product
ME-15 v1.1
03/2018
DIN rail relocated
ME-15 v1.2
05/2019
PE terminal block installed
This symbol placed on a product or packaging indicates that the product
should not be disposed of with other wastes as this may have a negative
impact on the environment and health. The user is obliged to deliver
equipment to the designated collection points of electric and electronic
waste. For detailed information on recycling, contact your local authorities,
waste disposal company or point of purchase. Separate collection and
recycling of this type of waste contributes to the protection of the natural
resources and is safe to health and the environment. Weight of the
equipment is specified in the document.
Contact:
Roger sp. z o.o. sp.k.
82-400 Sztum
Gościszewo 59
Tel.: +48 55 272 0132
Fax: +48 55 272 0133
Tech. support: +48 55 267 0126
E-mail: [email protected]
Web: www.roger.pl
Other Roger Enclosure manuals
