Roger ME-43 User manual
Roger Access Control System
Metal Enclosure ME-43
Operating Manual
Product version: v1.0
Firmware version: –
Document version: Rev. B
ME-43 Operating Manual.docx 2023-08-16
Page 2 of 6
1. APPLICATION
The ME-43 enclosure is dedicated to RACS 5 modules and devices which require installation on DIN
rail along with a 17Ah battery. The enclosure is equipped with 2 DIN rails, tamper contact and
main fuse switch. Access to the internal space of the enclosure is protected by a door fixed by
screws. Optionally, the door can be equipped with a key lock. The ME-43 is made of a metal sheet
painted with an anthracite grey powder coating.
2. INSTALLATION
1. The enclosure shall be installed indoors ensuring nominal environmental conditions as
stated in the Specification section.
2. All installation and maintenance work inside the enclosure shall be done with the 230VAC
power supply disconnected.
3. 230VAC power supply should be made with a three-wire cable including green-yellow PE
wire.
4. Mains power supply cable shall be fed into the enclosure through hole B and fastened to G
detail by a cable tie.
5. Connect the mains power cable as shown in the figure below (Fig. 1).
Fig. 1 Connection of 230VAC mains power to the terminal block
6. Protective wire M connected to the terminal block A, should be connected to the F
connector of the anti-shock protection PE located on the enclosure door (Fig. 2).
7. Other connections should be made in accordance with the instructions of the devices to be
mounted in the housing. Connection cables for installed devices must be fed into the
enclosure through C holes.
8. In order to arrange the cables inside the enclosure, they should be placed with cable ties to
the G detail. In order to use the G details, they must be levered first (ex. with a
screwdriver) and bend to the vertical position, then use a cable tie to fasten the bundle of
cables (Fig. 3).
9. Configuration and adjustments of the modules installed in the enclosure should be done in
accordance with their manuals.
10. To introduce cables into the enclosure from the upper or lower wall of the enclosure, form
the cable holes as indicated in Fig. 4.
11. Close the enclosure when electrical installation and configuration/test process is
accomplished.
12. Users of the system should be familiarized with the rules of switching off the electrical
circuit used to power the device.
ME-43 Operating Manual.docx 2023-08-16
Page 3 of 6
Caution
The installation can be done by qualified person only and with all necessary
certificates concerning connection and maintenance of 230VAC and low
voltage networks.
Caution
It is forbidden to use the enclosure without properly assured and
operational protective earthing.
Caution
System earthing must be performed carefully, properly and effectively.
It is forbidden to use PSU/transformer without properly performed electric
shock protection.
Caution
Follow the instructions in the manual and/or data sheet.
Failure to do so may result in equipment damage, electric shock, fire, injury,
or other consequences.
ME-43 Operating Manual.docx 2023-08-16
Page 4 of 6
Fig. 2 Internal view of ME-43 enclosure
ME-43 Operating Manual.docx 2023-08-16
Page 5 of 6
Fig. 3 Cable fixing method
Fig. 4 Forming a cable entry hole in the bottom or top wall of the enclosure
3. SPECIFICATION
Parameter Value
Electric Protection Fused terminal block 5A/250V
Tamper Protection Tamper contact NO/NC; 50mA/50VDC
DIN Rail 2 × 396mm
Material Metal sheet 0,8mm; anti-corrosion protection
Colour Anthracite grey RAL7016MAT
Battery Space for 17Ah battery
Environmental Conditions Indoor general conditions, relative humidity up
to 90%; temperature -10°C to +40°C
ME-43 Operating Manual.docx 2023-08-16
Page 6 of 6
Ingress Protection IP20
Internal Dimensions (HWD) 398×545×100mm
External Dimensions (HWD) 405x552x121mm
Weight 4,9kg
Compliant CE; RoHS
4. ORDERING INFORMATION
Product Description
ME-43 Standard version of the product
5. PRODUCT HISTORY
Version Date Description
ME-43 v1.0 07/2023 The first commercial version of the product
This symbol placed on a product or packaging indicates that the product
should not be disposed of with other wastes as this may have a negative
impact on the environment and human health. The user is obliged to deliver
equipment to the designated collection points of electric and electronic
waste. For detailed information on recycling, contact your local authorities,
waste disposal company, or point of purchase. Separate collection and
recycling of this type of waste contributes to the protection of the natural
resources and is safe for human health and the environment. Weight of the
equipment is specified in the document.
Contact:
Roger sp. z o. o. sp. k.
82-400 Gościszewo 59
Tel.: +48 55 272 0132
Fax: +48 55 272 0133
Technical Support: +48 55 267 0126
E-mail: [email protected]
www.roger.pl
Table of contents
Other Roger Enclosure manuals
