Rokka Play Cornish Fishing Boat User manual

Instruction Booklet
The Rokka &
The Cornish Fishing Boat
Accessory Pack

00 01
Introduction 01
Product Information 02
Warnings - Installation & Usage 03
Warnings - Cleaning Care & Maintenance 04
Parts 06
Assembling the Rokka 08
Assembling the Cornish Fishing Boat Accessory Pack 15
Accessory Packs 20
Contents
Congratulations on the
purchase of your Rokka.
We hope that your
children (and all the
family) will have hours
of fun playing with it!
We would love to hear
about your children’s
adventures and any
feedback you may have.
We pride ourselves on the
versatility, durability and safety
of the Rokka and it is intended
to be assembled very easily.
However, please read the following
information carefully before
assembling your Rokka and keep
this guide for future reference.
If any components are missing or
damaged please contact Rokka
Play Ltd for a replacement before
allowing your child to play on
the Rokka.
This user guide is for the
Rokka and Cornish Fishing
Boat Accessory Pack, product
number RP/ROK01/002.
Introduction

02 03
• Adult assembly required.
• The Rokka is intended for
children age 1 year and above.
• Please ensure your child is
supervised when playing on
the Rokka at all times.
• Please ensure your child is at
a safe distance when turning
the Rokka over to prevent
trapping or crushing.
• Do not allow children
to push their legs under
the seat if sitting on the
foot rest when the Rokka
is being used as a see-saw,
to prevent trapping.
• When on its side, do not allow
children to stand on Rokka
sides in order to prevent tipping
and falling.
• To prevent injury to your child
or damage to the Rokka, do not
allow children to swing on or
pull on the spoons, either when
attached to the Rokka or when
being used freely.
• Ensure that the Rokka is used
on a level stable surface,
whichever way up the Rokka is
being used, to prevent tipping.
• Make sure your Rokka has
room to rock freely without
obstruction.
• Do not place the Rokka near
an open re or other sources of
strong heat, such as electric bar
res, gas res, etc due to the
risk of re.
• Keep plastic bags and other
packing materials that may
pose a suffocation hazard away
from children and safely discard
as soon as possible.
Warnings – Installation & Usage
The Rokka is made from quality
birch plywood and the spoons are
made from sustainably sourced
beech wood. The fabric accessories
are made from 100% cotton, using
azo free dyes.
The Rokka and its accessories have
been independently tested and
comply with EN 71 regulations
(Safety of Toys). Rokka Play Ltd
regularly checks the materials and
workmanship it employs to produce
its products.
Product Information

04 05
Warnings – Cleaning, Care & Maintenance
• Be certain that all components
are correctly engaged and
xtures fastened before
you allow a child to play
on the Rokka (see assembly
instructions).
• Do not use any replacement
parts not manufactured
by Rokka Play as this may
affect your child’s safety.
• Do not use the Rokka if any
part or component appears to
be broken, damaged or missing.
• Remember to check on and
re-tighten the screws if
necessary on a regular basis.
• Clean with a damp cloth. Do not
use abrasive or harsh cleaning
products, we recommend you
use warm soapy water. Ensure
that excess liquid is wiped off
immediately.
• Do not allow items which cause
staining to sit on the surface of
the Rokka.
• Due to the natural materials
used, colour variations will
occur in the wood, however,
if left for prolonged periods
in sunlight, the overall colour
may darken. The materials
have been chosen for their
quality and aesthetics, they
should grow older gracefully!
With regular care your Rokka
should last generations.
• Fabrics should be hand washed
or spot cleaned with a damp
cloth. As the fabrics are made
from 100% cotton, repeated
washing may cause the fabric
to stretch slightly.
• Prolonged exposure in
sunlight may cause fading
of the fabric colours.
Warnings – Cleaning, Care & Maintenance
DO NOT LEAVE THE ROKKA
OUTSIDE IN THE RAIN OR IN
DAMP CONDITIONS AS THIS
MAY DAMAGE THE PROPERTIES
OF THE MATERIALS.

06 07
A) 2 x side panels
B) 2 x seats
C) 2 x seat backs
D) 1 x foot rest
E) 4 x large wooden spoons
F) 1 x small wooden spoon
Parts – Please check that you have all of the following components in the box
Rokka and Cornish Fishing Boat parts:
G) 1 x sail
H) 2 x seat cushions
I) 4 x orange sh fasteners
J) 12 x metal screws
K) 12 x metal dowels
L) 1 x Allen key
A) B) C) D) E)
F)
(Illustrations not to scale)
K)J)I)G) L)H)

0900
Assembling
the Rokka
Step 1 Inserting the dowels
STEP 1
12 x
MAKE SURE THE HOLES IN THE DOWELS ALIGN
WITH THE CORRESPONDING SCREW CHANNELS.
Use a screwdriver to turn the dowels so the holes
align and the surface of the dowels are ush with
the wood surface. They should not present any
difculty when inserting the screws later on. If they
do, you may need to either turn the dowel so it aligns
or push out the dowel and re-insert it correctly.
Insert 4 of the dowels (K) into foot rest (D), ensuring
that the smooth edges of the dowels all face the
same direction. The foot rest side with the smooth
side of the dowels will become the table top.
Insert 2 dowels into each of the seats (B) (4 in total),
ensuring that the smooth edge of the dowels appear
on the seat side without the circular grooves.
Insert the remaining dowels into the seat backs (C),
ensuring that the smooth side of the dowels face
away from the seat, when the shallower arch of the
seatback is at the top.

10 11
Step 2 Attaching the seat backs
STEP 2
2 x
Take one of the Rokka side panels (A)
and hold in bridge format. Position one
of the seat backs (C) against it in the
vertical groove, so that the deeper arch
of the seat back faces upwards and the
screws line up. Secure with a screw (J)
and Allen key (L).
Repeat this step by placing the second
seat back at the other end of the Rokka
side panel.
Step 3 Attaching the seats
2 x
STEP 3
Take one of the seats (B) and place it on the
top of one of the seat backs (C), so that the
circular grooves are nearer the seat back and face
downwards. (The edge of the seat which meets
with the seat back, is squarer than the other edge.)
Secure the seat into the joining horizontal
groove in the Rokka side panel (A) using the
screws provided.
Repeat this step by placing the second seat, on
the remaining Rokka seat back, ensuring again
that the circular grooves on the seat are nearer
the seat back and facing downwards and both
parts t snugly into the grooves in the Rokka side.

12 13
Step 4 Attaching the table
STEP 4
2 x
Take the foot rest (D) and position into middle
groove in Rokka side panel (A) so that the
smooth surface of the dowels face upwards
and the screw holes align. It should be a snug
t, requiring a push to insert it.
Secure one side of the foot rest to the side
panel using two screws.
(You may have noticed smaller grooves on the inside of the Rokka by the
footplate. These are for shelving which comes with other accessory packs.)
STEP 5
6 x
Step 5 Attaching the remaining side
Turn everything onto its side so that Rokka side
panel (A) is resting on the oor.
Take the second side panel (A) and place it on top
with the grooves facing downwards. If the other
components have been correctly tted, this panel
should locate very easily.
Secure this panel (A) to the seats, seat backs and
foot rest using the remaining 6 screws.
Once in place check all the screws are sufciently
tight to prevent movement in the parts. (Do not
over tighten screws as this may cause damage
or prevent you from being able to dissemble the
Rokka at a later date.)
STEP 5
6 x

14 15
Assembling
The Cornish Fishing
Boat Accessory Pack
So, now the fun bit, adding the Cornish Fishing Boat accessories!
The grown ups often need help here so make sure at least one
child is close by to help you if you get stuck!
Step 1
Hurray!
You have now
built your Rokka
The children can now have active
fun rocking with friends or practicing
their balancing. Alternatively, they
might like to march ‘The Grand Old
Duke of York’ over the top, take turns
at jumping off, or maybe sit quietly
to draw or eat a picnic.
Position your Rokka as a see-saw rocker.

16 17
Step 2 Attaching the sh fasteners
Take one of the four bright orange
sh fasteners (I) and slot it into one
of the four grooves with the circle
facing inwards and twist so you can
see the hole.
Step 3 Attaching the boom to the mast
DETAIL
SCALE 1 : 5
Take one of the four large wooden
spoons (E) (aka ‘the mast’) and slot
it through the hole in the small
wooden spoon (F) (aka ‘the boom’).
Make sure that the curved head of
the small wooden spoon is facing
upwards, towards the head of the
large spoon.