Roll-A-Shade Eclipse User manual

www.rollashade.com Rev: 06.25.2020 Page 1 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
RAS - Installation Instructions for Sun Sensor Eclipse
12101 Madera Way
Riverside, CA 92503
Phone: [phone]
Fax: [phone]
www.rollashade.com
A. Reawaken From Sleep Mode
1. Use paper Clip to press rest button
2. Check for Battery level on screen.
If low use usb charger to fully charge.
3. Test shades pairing with up or down buttons.
• If paired, move to Section “___” Installation
• If not paired, go to either Section “____” for
specic motor manufaturer
Note: Once plugged into Sun Sensor, you may plug the other
end into any port you have available.
Hardware Included Tools
Required
Phillips head
Drill
Sun sensor USB micro b
#8-18 x 3/4”
Screws
Eclipse screws
x2
x2
Sun sensor bracket
MICRO USB RESET BUTTON
MAIN MENU
Shade pairing
Position adjust
Sunshine
Tim er
Conguration
UP
BACK FORWARDSELECT
DOWN
If shades are paired (Both Somfy and RAS):
1. If shades are paired and sunshine is enabled there will be a
number next to the sun image on the screen with the arrows.
2. The shades will also be able to operate by using the arrows.
3. If both steps one and two work, then Date and Time can
be set.
a. Conguration > Date and Time
4. Eclipse can now be mounted in the window frame.
Click to Print
Click to Email

www.rollashade.com Rev: 06.25.2020 Page 2 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
1. Install Sun Sensor bracket into mullion vertically or horizon-
Note: Must be at least two screws in every bracket.
SIDE INSTALL ATION
TOP INSTALLATION BOTTOM INSTALLATION
B. Install Bracket

www.rollashade.com Rev: 06.25.2020 Page 3 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
C. Install Sun Sensor
1. Install Sun Sensor into bracket.
2. Sun Sensor installation check
Note: Must be at least two screws installed into Sun Sensor.
Note 2: Make sure screen and buttons are facing you.
Note: Make sure all screws are securely fastened into the
bracket and
Faces outside
BACK
Faces into room
FRONT
Note: Device is designed for interior installations only.
Correct - Perfect Placement
Correct - Sensor location clear of obstructing shadows
Incorrect - Sensor obstruction by shadows
Incorrect - Sensor obstruction by shadows
SUN SENSOR
SUN SENSOR
SUN SENSOR
SUN SENSOR
Roll-A-Shade Eclipse
FCC ID: 2AUXUECLIPSE-S1
Contains FCC ID: QOQMGM12P3
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
3. Test Sun Sensor

www.rollashade.com Rev: 06.25.2020 Page 4 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
Roll-A-Shade Eclipse Pairing:
WHEN SHADES ARE NOT PAIRED
1. To pair shades to Eclipse, go to Main Menu > Shade Pairing >
Pair with shade > Make sure shade is on > Either press button
on motor head OR press programming button on back of remote
8 times > shade will jog to show complete.
a. Shades will now be paired
Sun Sensor External Instructions
2. Make sure Sun Sensor is enabled to detect sun.
a. Main Menu > Sunshine > Enable
3. To conrm everything is set up, you will see a sun and a
number next to it on the a same screen with the arrows. You can
test the shades by conrming they raise and lower by manual
pressing the arrows.
4. Final step in programming is to set date and time.
a. Conguration > Date and Time
5. The Eclipse is now ready to be mounted into the window.

www.rollashade.com Rev: 06.25.2020 Page 5 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
Somfy Eclipse Pairing:
WHEN SHADES ARE NOT PAIRED BUT YOU HAVE A
REMOTE TRANSMITTER
1. Use your remote or wall switch to put shades in
programming mode.
a. Press the programming button on back of remote with
paperclip until shade jogs.
b. QUICKLY switch to Eclipse and go all the way to the left to
copy and paste the programming into the eclipse.
i. The screen with the arrows will quickly ash
“PROG” to show the Eclipse is in
programming mode.
c. The shades are now paired.
2. Make sure Sun Sensor is enabled to detect sun.
a. Main Menu > Sunshine > Enable.
3. To conrm everything is set up, you will see a sun and a
number next to it on the a same screen with the arrows. You
can test the shades by conrming they raise and lower by
manualpressing the arrows.
4. Final step in programming is to set date and time.
a. Conguration > Date and Time.
5. The Eclipse is now ready to be mounted into the window.

www.rollashade.com Rev: 06.25.2020 Page 6 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
Sun Sensor Warranty
Roll-A-Shade®warrants Eclipse to be free from defects in materials and workmanship for 5 years when used properly and
operated under normal conditions from the date of purchase. If Eclipse is found to be defective and covered by the warranty,
we will, at our option, repair or replace it free of charge. This product warranty does not cover any conditions or damages
resulting from misuse or abuse, accidents, alterations, neglect, damage by others, natural disasters, exposure to the elements,
or failure to follow Roll-A-Shade’s instructions with respect to installation, use and maintenance. The repair or replacement of
defective product is the purchaser’s sole remedy and the limit of Roll-A-Shade’s obligation. EXCEPT AS EXPRESSLY PROVIDED
IN THIS PARAGRAPH, ROLL-A-SHADE®MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND, NATURE OR
DESCRIPTION, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR
FITNESS OF ANY PRODUCTS FOR ANY PARTICULAR PURPOSE, AND HEREBY DISCLAIMS THE SAME. In no event shall
Roll-A-Shade®be liable or responsible for incidental or consequential damages or for any other direct or indirect damage, loss,
cost, expense or fee. WARRANTY Exclusions: • Installation and usage are not in accordance with our installation and operating
instructions. • Product has been opened, dismantled or returned with clear evidence of abuse or other damage. • Product has
been used to perform functions other than the functions it was designed to handle, namely motorizing window shades • Product
is used with electrical accessories (switches, relays, etc.) that have not been previously approved in writing by the Roll-A-Shade®.

www.rollashade.com Rev: 06.25.2020 Page 7 of 6© Copyright 2020 Roll-A-Shade Inc., All rights reserved. - Contractor #916075
ORIENTATION
Landscape
Landscape right
Port rait
Upside down
Note 2: Follwing images (F), (G), (H), (I) will be examples of each
display orientation.
LANDSCAPE
LANDSCAPE RIGHT
PORTRAIT UPSIDE DOWN
MAIN MENU
Shade pairing
Position adjust
Sunshine
Timer
Conguration
MAIN MENU
Shade pairing
Position adjust
Sunshine
Timer
Conguration
MAIN MENU
Pair
Adjust
Sun
Timer
Cong
(OPTIONAL) Sun Sensor Orientation
(A) Click the right button to access “Main Menu”. (B) Use navigation
buttons to access “Conguration”. (C) Navigate to “Display”. (D)
Click “Orientation”. (E) You will see four different options of display
orientations.
Note: Selection orientation in the display settings to adjust to
the following direction: top, bottom and/or side installation etc.
MAIN MENU
Shade pairing
Position adjust
Sunshine
Timer
Conguration
CONFIGURATION
Date/Time
Display
Version
Bluetooth
Sleep
DISPLAY
Orientation
100%
MAIN MENU
Pair
Adjust
Sun
Timer
Cong