Rollerdor RD20X2ELL User manual

Rollerdor RD20X2ELL Control Box, Edition 2022/1
Installation Guide for Roller Garage Doors
RD20X2ELL Control Box
Edition 2022/1

2
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.1
fig.2

3
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
1. INSTALLING RECEIVER BOX
(SAFETY EDGE)
1 Remove white plastic light cover by squeezing in each
side and lifting away (fig.1).
2 Remove small plastic cover at the bottom of the unit to
reveal screws and then remove all 4 screws from cover
to reveal control board inside (fig.1) Warning: Take
care when removing front cover as there is a membrane
ribbon that connects it to the main circuit board.
3 Place the Receiver box on the wall with the cable
pointing downwards at a comfortable height to operate
the push buttons, but out of the easy reach of children.
Between 1500mm up from the floor and 300mm down
from the roof/ceiling is recommended, mark the 4
fixings, drill and secure the unit to the wall (fig.2).
4 If you have a safety brake with a cable then run the
two core cable from the safety brake end across to
the same end as the receiver box, making sure to
securely fix the cable out of the way of the working
mechanism.
5 The Glands at the bottom are for the cables to be
inserted, (1) motor wire (2) power wire (3) safety brake
if supplied.
6 Wiring as follows (fig.3 & 4):
Terminal 1 – Earth Motor Wire
Terminal 2 – Earth Power Wire
Terminal 3 – Power Brown Live Wire
Terminal 4 – Power Blue Neutral Wire
Terminal 5 – Motor Open Wire (left hand motor
Black / right hand motor Brown)
Terminal 6 – Motor Blue Neutral Wire
Terminal 7 – Motor Close wire (left hand motor
Brown / right hand motor Black
Safety Brake (fig.5 & 6):
Terminal 21 - Safety Brake = Blue Safety Brake
Wire / No safety Brake = Link cable to Terminal
22.
Terminal 22 - Safety Brake = Brown Safety Brake
Wire / No Safety Brake = Link wire to Terminal 21.
fig.3 - Right Hand Motor
fig.4 - Le Hand Motor
fig.5 - Safety Brake
fig.6 - No Safety Brake

4
Rollerdor RD20X2ELL Control Box, Edition 2022/1
2. ELECTRICAL CONNECTIONS
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

5
Rollerdor RD20X2ELL Control Box, Edition 2022/1
3. SETTING UP WIRELESS
SAFETY EDGE KIT
(OPTICAL EDGE)
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
CHECKING BASE RAIL UNIT
1 Your base rail unit is already installed on one
side of the last slat of your curtain (usually
nearest the motor) it is a small black unit,
there are 2 screws one each end, undo screws
and remove the lid (fig.8).
2 Check the wiring inside the base rail unit and
dip switch position (fig.9) Terminal 4: Green
wire [ signal ] Terminal 5: Brown wire [ power
supply + ] Terminal 6: White wire [ power
supply - ] dipswitch 1 should be on and dip
switch 2 off.
3 Batteries: The unit comes with Qty 2 AA size
3.6V lithium batteries but will work with Qty
2 AA 1.5v batteries, there is a sliding switch
to change the voltage from 3.6v to 1.5v
depending on which is used and must be
in the correct position to work. Please pay
attention to the polarity!
4 Test safety edge connection: the RED LED on
the base rail should be out, slide dip switch
2 into the ON position, you now have 30
seconds to test the connection by squeezing
the base rail rubber, when you squeeze the
rubber the RED LED should light up, this will
confirm a good circuit, return dip switch 2 to
off. If the RED LED doesn’t light up check the
wires to make sure all connections are good
and then retest, if the red light is constantly
on as soon as you slide the switch please
contact your provider as there may be a fault
with the Optics.
The control box is supplied in Hold to Run operation for open and close, if the limits of the motor have not been set then
please set them now using the PROG (P1/UP) & DEL (P2/Down) buttons, if when you press and hold either of the buttons
the unit just beeps then you will need to put the unit into Hold to Run by pressing and holding both PROG (P1) & DEL (P2)
buttons at the same time until you hear a single beep (fig.7). Once you have finished setting limits once again press and
hold both PROG (P1) & DEL (P2) buttons at the same time until you hear a single beep to return to single press operation.
fig.7
fig.8
fig.9

6
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.10
CHECKING CONTROL BOX
PROGRAMMING BASE RAIL UNIT
1 Control box Dip Switches: check dip switches on main board (fig.11) dip switch number 1 & 2 should be on
and number 3 off.
2 Inside the control box is a separate circuit board which is plugged into the main circuit board (fig.12)
check the RED LED L3 if this is intermittently flashing then the base rail unit has been paired, move onto
Programming Transmitter’s section, if LED 3 is flashing then continue to Programming Base Rail section.
1 Push and hold the red P1 programming button on the plug in circuit board (fig.12) for roughly 2 seconds
until L1 and L2 LED’s flash.
2 Go to the base rail unit on the curtain, press and hold the white button (fig.10) of the unit for 2 seconds.
The RED LED on the unit will flash.
3 Return to the control box and check that the LED L3 is intermittently flashing this will signify programming is
complete, if LED 3 it is still solid then repeat the process.
fig.12fig.11
White button

7
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
PROGRAMMING TRANSMITTER’S
Programming Transmitters 2 Channel:
1 Press P1 (PROG) button two times, on last press HOLD causing the buzzer to emit a continuous sound.
2 Whilst P1 (PROG) is still pressed, press the top button on the transmitter, you will hear a faster beeping sound.
Deleting ALL transmitters:
1 Press P2 (DEL) 5 times and on last press HOLD for at least 10 seconds, buzzer emits a rapid beeping sound.
2 Once the sound becomes continuous release the P2 button.

8
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
WIRELESS KEY PAD
1 Undo and remove the small screw at the bottom and lift off
the front cover.
2 Using the back-plate as a template, mark the positions
of two suitable fixing holes onto the wall then secure the
back-plate to the wall using the plugs and fixing screws
provided.
3 Install the 9v alkaline battery that has been supplied then once
set up and programming is completed push the keypad onto
the back-plate and secure in place with the screw.
INSTALLATION
1 The keypad is supplied with a factory access code number
"12345".
2 To pair keypad to receiver box, enter the Access code
“12345”, within 5 seconds press and release PROG (P1)
button, then press and hold PROG (P1) button. You will hear
a continuous beep from the control box, whilst holding
the button press and hold Number 1 on the keypad, the
continuous beep will change to faster beep on hearing this
release all buttons and the keypad is now programmed.
PAIRING USING ACCESS CODE
For security reasons it is essential that the access code num-
ber is changed to another 5 digit number these numbers can
be in any combination of numbers 0-9, excluding A and B.
To change access code follow this sequence: Enter access code
“12345”, press M1 button (white button on the back of the
keypad) a beep will be emitted, enter your new 5 digit code,
within 1 second enter this same code again, when you hear a
continuous beep for approx. 2 seconds this confirms the code
has been changed.
CHANGING ACCESS CODE
Enter your individual 5 digit code each number will emit
a short beep to signify it has been registered and the final
number will give a longer beep to say full code has been
entered, Press either number 1 to open or number 3 to close.
OPERATION

9
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
1 The curtain is supplied with stops at each end to stop an uneven floor having an eect (fig.13) but if the curtain
reopens having hit the floor the safety edge exclusion should be set to ‘turn o’ the edge 50mm before it hits the floor.
Please be aware the safety edge will have to return to the top limit before closing and the alarm will be disabled.
SAFETY EDGE EXCLUSION ZONE
fig.13

10
Rollerdor RD20X2ELL Control Box, Edition 2022/1
HOLIDAY MODE
ALARM FUNCTION
The “Holiday mode” allows the user to
temporarily lock the front cover buttons.
Note: when the mode is activated, wireless and
wired input commands are still enabled.
For the alarm function you must install the speaker that has been
supplied, this should be screwed in to replace one of the glands
at the bottom of the box and the cable will be plugged into the
board at the bottom right corner next to terminal 22 (fig.14).
To test your alarm function, once the door is closed and the
courtesy light has gone out, use the manual crank to wind the
door open a little, you may need to li and shake the base rail
to activate as the smooth motion of winding may not trigger the
alarm.
Press the STOP button in the front cover and keep
it pressed for 5 seconds.
The buzzer makes one beep.
ACTIVATION
Press STOP button in the front cover and keep it
pressed for 5 seconds.
The buzzer makes one beep and LED
starts to flash faster.
Press any button of any memorized transmitter
within 10 seconds.
The buzzer makes one beep and LED
turns o.
DEACTIVATION
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
fig.14

11
Rollerdor RD20X2ELL Control Box, Edition 2022/1
Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.
TROUBLESHOOTING (WHAT TO DO IF...)
ACOUSTIC SIGNALS FROM THE CONTROL UNIT
Press P1 eight times and keep it pressed.
The buzzer emits a continuous sound.
Activate the shock sensor.
Once the memorisation is successfully
completed, the buzzer emits a fast
intermittent sound.
...
( ) keep it pressed
continuous sound intermittent sound
ACTIVATE THE
SHOCK SENSOR
P1 8X

12
Rollerdor RD20X2ELL Control Box, Edition 2022/1
OTHER POSSIBLE ISSUES
LED IN THE FRONT COVER
ON: safety alarm activate (see the specific alarm).
OFF: normal functioning.
1 flash - pause: keypad locked (holiday mode).
Flashing slowly: low batteries in the bottom slat
transmitter (TCSP)
Led ON: The control unit is powered.
RADIO CARD (MASTER)
Flashing: normal functioning.
ON: transmission error or drained batteries.
ON: activated safety alarm, transmission error or
drained batteries.
OFF: normal functioning.
Not used.

Rollerdor RD20X2ELL Control Box, Edition 2022/1
Rollerdor Ltd
10 & 12 Jarrold Way
Bowthorpe Employment Area
Norwich
Norfolk NR5 9JD
[phone]
[e-mail]
www.rollerdor.net
Company Registration Number. 10676267
Registered Oice Address:
Rollerdor Ltd, Bankside 300 Peachman Way,
Broadland Business Park, Norwich,
Norfolk, United Kingdom, NR7 0LB
Edition 2022/1