Romina 9510 User manual

ASSEMBLY INSTRUCTIONS
FOR YOUR
9510 STATIONARY CRIB
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominafurniture.com
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
IMPORTANT: PLEASE, READ ALL
INSTRUCTIONS BEFORE
ASSEMBLING! PLEASE, SAVE
INSTRUCTIONS FOR FUTURE USE
WARNING: THE PROPER USE OF THIS CRIB IS IMPORTANT FOR
YOUR BABY'S SAFETY. TO KEEP YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH, CAREFULLY READ
AND FAMILIARIZE YOURSELF WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET. KEEP THIS
INSTRUCTION BOOKLET FOR FUTURE USE.
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
this picture shows how your crib
should look like after completing assembly
NOTE: THE STYLE OF YOUR CRIB,
MATTRESS SUPPORT OR
TODDLER RAIL MAY VARY FROM
WHAT IS PICTURED IN THE
INSTRUCTION SHEET

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINAL LUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECUERLY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.

9510 BOX CONTENT Please locate and confirm that
you have the following parts:
EP. end panel = 2
UP. upper panel = 2
LP. lower panel = 2
MS. mattress support = 1
BF. base frame = 1
WB. wooden block = 4
one bag of hardware with the following:
1. Allen wrench =
2. one storage pouch and two plastic ties
3. Allen bolt (40mm - 1 9/16") = 18
4. rounded head bolt (30mm - 1 1/8") = 4
5. rounded head bolt (15mm - 5/8") = 4
6. "butterfly" type nut = 4
7. bigger “internal star” lock washer = 18
8. smaller “external star” lock washer = 8
9. threaded metallic dowel = 8
10. cam fitting = 8
11. wooden dowel (40mm - 1 9/16") = 8
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
Do not use a power screwdriver which
can cause screws to break or strip.
1
Required tools:
CAUTION:
Note:
TIGHTEN
During the assembly process whenever using screws or
bolts, check each by placing the screw / bolt on the hardware
diagram which is drawn in actual size. Be sure to use the proper
size and shape specified in the instructions. Be sure to
the screws / bolts when you are asked
to do this.
COMPLETELY
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
Phillips screwdriver (not included)
printed in full size
4
5
6
8
7
1
Note: The item number of your product
is located on the inner side of the left
pannel, on a black and white label.
Please, refer to this number in the event
that you need to call ROMINA
FURNITURE or your local distributor.
Thank you.
9
10
11
9
10
EP UP
MS
WB
EP
UP
LP
LP
BF
3

FIGURE 1
STEP 1 (Two adults are required to complete this step)
(EP)
(9)
(10)
(LP) (EP).
(1)
(10)
Do not overtight the cams! This is not a fixture involved in
your child safety.
Take one of the end panels of your crib, place it on the
floor taking care not to scratch its finish and using a Phillips
screwdriver (not supplied) or just the hand insert four metallic
dowels into the lower threaded inserts. Please see the
assembly tip for dowel correct positioning.
Insert four cam fittings into the bigger holes located in the
lower panels taking care that the little arrow of the cam is
pointing to the end panel.
Attach the lower panels to the end panel
Then using the supplied Allen wrench and moderate force,
slightly rotate the cams clockwise (see the cam’s rounded
arrow) by about 90 deg to 120 deg until become tight.
9x 4
10 x 4
LP
little
arrow
r
o
u
n
d
e
d
a
r
r
o
w
REQUIRED
9
9
10
10
EP
LP
0+
-
assembly tip

3+7
3+7
LP
FIGURE 2 3x 4
7x 4
REQUIRED
STEP 2 (Two adults are required to complete this step)
(UP) (EP)
(LP) STEP 1
(3) (7)
(1)
Turn the end panel and the lower panels in normal position.
Attach the upper panels to the end & lower panels &
as they resulted after completing , using four Allen
bolts , four bigger washers and the Allen wrench supplied
.
Do not completely tighten the bolts at this step, you will be
asked to do this later.
UP
LP
UP
EP
3+7

9
EP
9x 4
10 x 4
little
arrow
r
o
u
n
d
e
d
a
r
r
o
w
REQUIRED
0+
-
assembly tip
10
10
9
3+7
3+7
3x 4 7x 4
FIGURE 3
STEP 3
REMINDER
(Two adults are required to complete this step)
(EP) STEP 1 & 2 (9)
(10) (3) (7) (1)
(9)
(EP)
(10)
(EP) (LP).
(1) (10)
Do not overtight the cams! This is not a fixture involved in your child safety.
completely tighten 8 (3+7)
STEPS 1 & 2
8
4 (3+7) (UP);
4 (3+7) (UP).
Attach the other end panel to the part of your crib as it resulted after completing , using four metallic dowels , four
cam fittings , four Allen bolts , four bigger washers and the Allen wrench supplied .
Using a Phillips screwdriver (not supplied) or just the hand insert four metallic dowels into the lower threaded inserts of the second
end panel . Please see the assembly tip for dowel correct positioning.
Insert four cam fittings into the bigger holes located in the lower panels taking care that the little arrow of the cam is
pointing to the second end panel. Attach the second end panel to the lower panels Then using the supplied
Allen wrench and moderate force, slightly rotate the cams clockwise (see the cam’s rounded arrow) by
about 90 deg to 120 deg until become tight.
all Allen bolts
remained untightened from .
You have a total of Allen bolts, distributed as following:
- bolts in one of the upper panels
- bolts in the other upper panel
Now, you must
WARNING:
VERY
IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL BOLTS LISTED IN .
COMPLETELY TIGHTEN
8 STEP 3

STEP 4
REMINDER
(Two adults are required to complete this step)
(WB) (LP)
(11) (3)
(7) (1)
(LP)
(BF) (3)
(7) (1)
completely tighten 10 (3+7)
STEP 4
10
4 (3+7) (WB);
6 (3+7) (BF)
Turn the crib upside down, taking care not to scratch its finish.
Attach the wooden blocks to the lower panels using
eight wooden dowels , four Allen bolts , four bigger
washers and the Allen wrench .
The smaller holes of the wooden blocks must facing towards the
middle part of the lower panels .
Attach the base frame using six Allen bolts , six bigger
washers and the Allen wrench .
all Allen bolts
used at .
You have a total of bolts, distributed as following:
- Allen bolts in the wooden blocks
- Allen bolts in the base frame .
Now, you must
WB
BF
3+7
WB
3+7
11
11
11
3+7
3+7
11
REQUIRED
x 10
7x 10 3
FIGURE 4
WB
WB
3+7
11
11
3+7
11
11
11 x 8
WARNING:
VERY
IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO
ALL BOLTS LISTED IN .
COMPLETELY TIGHTEN
10 STEP 4
3+7
3+7
3+7
3+7
3+7
3+7

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger
round head bolts , 4
STEP 5
(4) "butterfly" type nuts , 4
smaller lock washers and a Phillips screwdriver
(not supplied). The lock washer must be attached
to the bolt after the bolt passed through the frame
and the metallic bracket of the mattress support
and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see ).
(6)
(8)
FIGURE 5
Do not completely tighten the bolts at
this step, you will be asked to do this later.
NOTE: THE STYLE OF YOUR CRIB OR
OF YOUR MATTRESS SUPPORT MAY
VARY FROM WHAT IS PICTURED IN
THE INSTRUCTION SHEET
FIGURE 5
To adjust the vertical position of your mattress support you must remove the mattress support from the crib
remove all four bolts & nuts , lower the frame and insert the bolts back into
the corresponding holes, according to the desired height (see ). Then, you must attach the lock
washers and the nuts as described in , attach the mattress support to the crib
and tighten all the bolts.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(please see ),
(please see
) completely
TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH,
STEP 6
STEP
6
(4+8+6) (4)
FIGURE 5
(8) (6) STEP 5
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest position, the
mattress support frame must be placed directly over the inner wooden blocks. Before tighten the bolts, you must
slightly press the mattress support frame to make sure this position is achieved.
WARNING:
IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (4+8+6) &
(5+8) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
REQUIRED
4+8+6
4+8+6
4+8+6
4+8+6
4+8+6
4x 4 8x 4 6x 4

REQUIRED
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S TO
ALL BOLTS LISTED IN .COMPLETELY TIGHTEN 8 STEP 6
FIGURE 6
the mattress support to the inner wooden
blocks using four smaller rounded head bolts
STEP 6 (Two adults are required to complete this
step)
completely tighten 8 (4+8+6,
5+8)
8
4 (4+8+6)
(MS);
4 (5+8)
(Two adults are required to complete this
step)
Turn your crib with its side on the floor, taking care not to
scratch its finish.
all bolts
involved in mattress support fixing using a Phillips
screwdriver (not supplied).
You have a total of bolts, distributed as following:
- bigger rounded head bolts in the mattress
support
- smaller rounded head bolts in the wooden
blocks;
Turn your crib with its base frame back on the floor.
A
After completing assembly, your crib should look like the
one depicted on the first page of this manual
Attach (MS)
(5), four
smaller washers and a Phillips screwdriver (not
supplied). The lock washer must be attached to the bolt
before inserting the bolt through the metallic bracket of the
mattress support.
Now,
ttach the storage pouch supplied to the mattress support
spring using two plastic ties (also supplied). Store this
instruction booklet in the storage pouch for future use.
(8)
you must
REMINDER
STEP 7
MS
5x 4 8x 4
5+8
5+8
5+8
5+8
4+8+6
4+8+6
4+8+6
4+8+6
WARNING!
COMPLETELY TIGHTEN!

TODDLER RAIL OPTION OF
YOUR 9510 STATIONARY CRIB
(THE TODDLER RAIL IS SOLD SEPARATELY)
NOTE: Y
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL
CAN BE FOUND INSIDE OF TR 9510 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
OU CAN ATTACH A TODDLER RAIL TO
YOUR CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM ( ODDLER AIL ).TR 9510 T R 9510

DAYBED OPTION OF
YOUR 9510 STATIONARY CRIB
(THE CONVERSION KIT IS SOLD SEPARATELY)
NOTE: Y
ASSEMBLY INSTRUCTIONS FOR DAYBED RAILS
CAN BE FOUND INSIDE OF DB 9510 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
OU CAN ATTACH TWO DAYBED RAILS TO
YOUR CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM ( AY ED ).DB 9510 D B 9510

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
for updates, special offers and more new designs.
www.rominakidsfurniture.com
Team
Thank you for being one of our distinguished clients.
Furniture