Romina 8501 User manual

IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY INSTRUCTIONS
FOR YOUR 8501 & 8501 SP
CONVERTIBLE CRIBS
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION
20 Corporation Row, Edison, NJ 08817
Phone [phone], Fax [phone]
www.rominafurniture.com
Furniture
DO NOT THROW OUT THIS INSTRUCTION BOOKLET
this picture shows how your crib
should look like after completing assembly
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
T H E Y C A N C A U S E S U F F O C A T I O N .
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

INFANTS CAN SUFFOCATE ON SOFT
BEDDING. NEVER ADD A PILLOW OR
COMFORTER. NEVER PLACE ADDITIONAL PADDING UNDER AN
INFANT. FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
CAUTION: ANY MATTRESS USED
IN THIS CRIB SHALL BE AT LEAST
27 BY 51 IN. WITH A THICKNESS
NOT EXCEEDING 6 IN.
- TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS BE
PLACED ON THEIR BACKS TO SLEEP, UNLESS OTHERWISE ADVISED BY YOUR PHYSICIAN.
STRANGULATION HAZARD:
- STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS
OVER A CRIB OR ATTACH STRINGS TO TOYS.
- TO HELP PREVENT STRANGULATION TIGHTEN ALL FASTENERS. A CHILD CAN TRAP PARTS
OF THE BODY OR CLOTHING ON LOOSE FASTENERS.
- DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
FALL HAZARD:
- WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD
SERVE AS STEPS FOR CLIMBING OUT.
- STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN.
(89 CM).
- CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR
OTHER FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY
AND FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER
FASTENERS. DO NOT USE CRIB IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN.
CONTACT ROMINA FURNITURE FOR REPLACEMENT PARTS AND INSTRUCTIONAL
LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
- IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
- FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB.
- READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE
USE. A STORAGE POUCH & 2 PLASTIC TIES HAVE BEEN PROVIDED IN THE HARDWARE BAG.
ATTACH POUCH TO MATTRESS SUPPORT WITH PLASTIC TIES AND STORE THE
INSTRUCTIONS THERE.
- NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CAN CAUSE SUFFOCATION.
- INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS TOO
SMALL. - DO NOT USE A WATER MATTRESS WITH THIS CRIB.
- BEFORE USING THIS CRIB RECHECK ALL SCREWS AND BOLTS TO BE SURE THEY ARE
FASTENED SECURELY. A PERIODIC CHECK SHOULD BE MADE TO BE SURE THESE ITEMS
REMAIN TIGHT.
- TO AVOID HEAD INJURY, DO NOT ALLOW ANY CHILD TO PLAY UNDERNEATH CRIB.
WARNING!

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL. *DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
A DRY CLOTH, WILL PRESERVE THE ORIGINAL LUSTER AND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS. *LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!

Please locate and confirm that
you have the following parts:
HB. headboard = 1
FB. footboard = 1
LP. left panel = 1
RP. right panel = 1
SB. stabilizing bar = 2
MS. mattress support = 1
WR. wooden rail = 1
WB. wooden block = 2
one bag of hardware with the following:
1. Allen wrench = 1
2. one storage pouch and two plastic ties
3. Allen bolt (50 mm - 1 31/32") = 4
4. Allen bolt (60 mm - 2 1/4") = 8
5. rounded head bolt (30 mm - 1 3/16") = 4
6. rounded head bolt (15 mm - 19/32") = 4
7. "butterfly" type nut = 4
8. screw-in dowel = 2
9. cam fitting = 2
10. bigger “internal star” lock washer = 12
11. smaller “external star” lock washer = 8
12. wood screw (20mm - 3/4”) = 3
Required tools: Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
CAUTION: Do not use a power screwdriver which
can cause screws to break or strip
Note: During the assembly process whenever using screws or bolts, check
each by placing the screw / bolt on the upper diagram which is drawn in actual
size. Be sure to use the proper size and shape specified in the instructions.
Be sure to COMPLETELY TIGHTEN the screws / bolts when you are asked to do this.
Phillips screwdriver (not included)
N o t e :
T h e i t e m
number of your
product is located on
the inner side of the left
panel, on a black and white
label. Please, refer to this number in
the event that you need to call ROMINA
FURNITURE or your local distributor. Thank
you.
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
1
7
8
9
MS
SB
RP
LP FB
HB
2
WR
WB
12
10 11
printed in full size
3
4
11
10
7
56
8
9
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

FIGURE 1
HB
FB
RP
LP
SB
SB
REQUIRED
4+10
4+10
4+10
4+10
4+10
4+10
4+10
4+10
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET
3+10
3+10
3+10
3+10
STEP 1 (Two adults are required to complete this step)
Take the footboard of your crib (FB) and carefully place it on the floor
with the drilled side on top, taking care not to scratch its finish.
Align the tenons attached at the end of the stabilizing bars (SB) with
the lower holes existing on the inner faces of the left and right panels
of the crib (LP) & (RP).
Be sure that the metallic inserts faces of the stabilizing bars are facing
towards the inside of the crib (follow the instructions attached to the
stabilizing bar).
Attach the stabilizing bars (SB) to the left and right panels using all
smaller Allen bolts (3), 4 washers (10) and the Allen wrench supplied
(1).
Do not completely tighten the bolts at this step, you will be asked to do
this later.
Carefully, take the assemble consisting of left an right panels and both
stabilizing bars (LP + SB + SB + RP) and put it over the footboard
(FB).
Using 4 bigger Allen bolts (4), 4 washers (10) and the Allen wrench
supplied (1), fix the right and left panels (RP) & (LP) to the footboard
(FB).
Take the headboard (HB) and carefully place it over the part of your
crib as resulted after completing the above steps.
Using 4 bigger Allen bolts (4) , 4 washers (10) and the Allen wrench
supplied (1), fix the headboard to the right and left panels (RP) & (LP).
Always start the threads by hand to assure you don't strip the
threads.
Do not completely tighten the bolts at this step, you will be asked
to do this later.

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
STEP 2
Assemble the mattress support using 4 bigger
round head bolts (5), 4 "butterfly" type nuts (7), 4
smaller lock washers (11) and a Phillips
screwdriver (not supplied). The lock washer must
be attached to the bolt after the bolt passed
through the frame and the metallic bracket of the
mattress support and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all four bolts in the same position (see
FIGURE 2).
Do not completely tighten the bolts at
this step, you will be asked to do this later.
FIGURE 2
5
7
5
7
5
7
5
7
5
7
11
11
11
11
11
A D J U S T I N G T H E H E I G H T O F Y O U R M A T T R E S S S U P P O R T
To adjust the vertical position of your mattress support you must remove all four bolts & nuts (5+11+7),
loosen all four bolts (6+11), lower the frame and insert the bolts (5) back into the corresponding holes,
according to the desired height (see FIGURE 2). Then, you must attach the lock washers (9) and the nuts (7)
as described in STEP 2 and completely tighten all bolts.
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the stabilizing bars. Before tighten
the bolts, you must slightly press the mattress support frame to make sure this position is achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (5+11+7)
& (6+11) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

STEP 3
Mount the mattress support (MS) on the stabilizing
bars as these resulted after STEP 2, using all four
smaller rounded head bolts (6) and four washers (11)
supplied and a Phillips screwdriver (not supplied).
The lock washer must be attached to the bolt before
inserting the bolt through the metallic bracket of the
mattress support.
Now, you must completely tighten all 8 bolts
(5+11+7, 6+11) involved in mattress support fixing
using a Phillips screwdriver (not supplied) and all 12
Allen bolts remains not tightened from all previous
steps (see FIGURE 3).
REMINDER
You have a total of 20 bolts, distributed as following:
- 4 smaller Allen bolts (3+10) in the stabilizing bars
(SB);
- 8 bigger Allen bolts (4+10) in the headboard and
footboard (HB) & (FB);
- 4 smaller rounded head bolts (6+11) in the stabilizing
bars (SB);
- 4 bigger rounded head bolts (5+11+7) in the mattress
support (MS).
STEP 4 (Two adults are required to complete this
step)
Turn your crib with its feet back on the floor.
Attach the storage pouch supplied to the mattress
support spring using two plastic ties (also supplied).
Store this instruction booklet in the storage pouch for
future use.
After completing assembly, your crib should look like
the one depicted on the first page of this manual
HB
FB
RP LP
SB
MS
WARNING!
COMPLETELY TIGHTEN!
REQUIRED
WARNING: TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL 20 BOLTS LISTED IN STEP 3.
FIGURE 3
4+10
5+11+7
6+11
4+10
4+10
4+10
4+10
4+10
5+11+7
5+11+7
5+11+7
6+11
6+11
6+11
3+10
3+10
4+10
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

ASSEMBLY INSTRUCTIONS
FOR DAYBED OPTION
OF YOUR 8501 & 8501 SP
CONVERTIBLE CRIBS
WARNING (FOR DAY BED OPTION ONLY):
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN 50LB.
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
DO NOT THROW OUT THIS INSTRUCTION BOOKLET.
20 Corporation Row, Edison, NJ 08817
Phone [phone], Fax [phone]
www.rominafurniture.com
Furniture
this picture shows how your daybed
should look like after completing STEP E
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

SB
MS
FB
FIGURE A
REQUIRED
STEP A (Two adults are required to complete this step)
Take your crib and carefully place it on the floor with the footboard (FB) on top,
taking care not to scratch its finish.
Remove all four bigger Allen bolts and washers (4+10) used to fix the footboard
(FB).
Adjust the mattress support (MS) to its lowest position (see STEP 2 for details).
Now, you must completely tighten all 8 bolts (5+11+7, 6+11) involved in mattress
support fixing using a Phillips screwdriver (not supplied).
REMINDER
You have to completely tighten a total of 8 bolts, distributed as following:
- 4 smaller rounded head bolts (6+11) in the stabilizing bars (SB);
- 4 bigger rounded head bolts (5+11+7) in the mattress support (MS).
4+10
4+10
4+10
4+10
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET
WARNING!
COMPLETELY TIGHTEN!
WARNING: TO KEEP
YOUR BABY SECURE AND
SAFE, AND TO AVOID
POTENTIAL INJURY OR
D E AT H , I T ' S V E R Y
I M P O R T A N T T O
COMPLETELY TIGHTEN
ALL 8 BOLTS LISTED IN
STEP A.

y
x
y
x
x
x
FB
top rail
FB middle
panel
STEP B
Take the footboard of your crib and carefully hold it in vertical position, with its feet on
the floor.
Using the supplied Allen wrench (1) completely unscrew all four Allen bolts and
washers (x) (previously mounted in factory) then remove the top rail.
You will find another factory mounted Allen bolts and washers (y), one for each leg of
your footboard. Remove two smaller Allen bolts (y) and then the footboard middle
panel resulted by pulling it upward (see FIGURE B). Please, store the top rail, the
middle panel and the Allen bolts resulted in a proper place, taking care not to scratch
the wood finish.
FIGURE B
REQUIRED

6
8
STEP C
Using a Phillips screwdriver (not supplied) or just the hand, insert two dowels (8) into the metallic inserts holes found into each leg’s top (please see the
assembly tip for dowel correct positioning).
Insert two cam fittings (9) into the bigger holes found into the wooden blocks (WB), taking care that the little arrow of the cam is pointing downwards, to the
drilled face of the wooden block (see FIGURE C for details).
Using the factory installed wooden dowels, align the wooden blocks and attach them to the legs.
Then using the supplied Allen wrench (1) and moderate force, slightly rotate every cam fitting (9) clockwise (see the cam’s rounded arrow) by about 90 deg
to 120 deg until become tight. Don’t over-tight the cams! This is not a fixture involved in your child safety.
Take the supplied wooden (WR) rail and attach it to your footboard using a Phillips screwdriver (not supplied) and three wood screws (12).
FIGURE C
6
8
WB
WB
WR
12
12
12
8
6
WB
REQUIRED
FB
0+
-8
8
8
assembly tip
little
arrow
r
o
u
n
d
e
d
a
r
r
o
w

STEP D
Take the footboard of your crib (FB) as resulted after
completing STEP C and carefully place it back over the
rest of the crib. Using 4 bigger Allen bolts (4), 4
washers (10) the and the Allen wrench supplied (1), fix
footboard (FB) to the right and left panels (RP) & (LP).
Now, you must completely tighten all 4 Allen bolts
remains not tightened from all previous steps.
REMINDER
You have to completely tighten a total of 4 bolts,
distributed as following:
- 4 bigger Allen bolts (4+10) in the footboard (FB);
STEP E (Two adults are required to complete this
step)
Turn the resulted daybed with its feet back on the floor.
After completing assembly, your daybed should look
like the one depicted on the first page of this section.
FIGURE D
WARNING!
COMPLETELY TIGHTEN!
WARNING: TO KEEP
YOUR BABY SECURE AND
SAFE, AND TO AVOID
POTENTIAL INJURY OR
D E AT H , I T ' S V E R Y
I M P O R T A N T T O
COMPLETELY TIGHTEN
ALL 4 BOLTS LISTED IN
STEP D.
REQUIRED
4+10
4+10
4+10
4+10
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

TODDLER RAIL OPTION OF
YOUR 8501 & 8501 SP
CONVERTIBLE CRIBS
(THE TODDLER RAIL IS SOLD SEPARATELY)
NOTE: YOU CAN ATTACH A TODDLER RAIL TO
YOUR CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM TR 8501 (TODDLER RAIL 8501).
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL
CAN BE FOUND INSIDE OF TR 8501 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

FULL SIZE BED OPTION OF
YOUR 8501 & 8501 SP
CONVERTIBLE CRIBS
(THE CONVERSION KIT IS SOLD SEPARATELY)
NOTE: YOUR 8501 CONVERTIBLE CRIB CAN CONVERT INTO A FULL SIZE
BED WITH THE PURCHASE OF ROMINA FURNITURE ITEM CODE CKC
8501 (CONVERSION KIT FOR CRIBS, code 8501).
ASSEMBLY INSTRUCTIONS FOR FULL SIZE BED OPTION CAN BE FOUND
INSIDE OF CKC PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR LOCAL
DISTRIBUTOR FOR MORE INFORMATION.
NOTE: THE STYLE OF YOUR
CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
P I C T U R E D I N T H E
INSTRUCTION SHEET

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as beautiful and unique as you and your baby are. · To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for being one of our distinguished clients.
Furniture