Romina TR 4501 User manual

IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY INSTRUCTIONS
FOR TODDLER RAILTR 4501
(PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 4501 CONVERTIBLE CRIB”)
If you don’t have your assembly manual anymore, you can download a copy
from the “Assembly manuals” section of our website
or request one at
www.rominakidsfurniture.com
[email protected].
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
WARNING:
.
THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY'S SAFETY. TO KEEP
YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE
§
§
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 IN BY 51 5/8 IN BY 4 IN, WITH A
THICKNESS NOT EXCEEDING 6 IN.
THE MINIMUM AGE OF YOUR CHILD SHALL NOT BE
LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALL NOT BE GREATER THAN 50LB.
DO NOT THROW THIS INSTRUCTION BOOKLET
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominafurniture.com
Furniture
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION

Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
included).
Phillips screwdriver (not included)
STEP 1TR
STEP 2TR
Completely tighten
(Two adults are required to complete this step)
STEP A
( R) (FB) (2)
STEP 2TR
Transform your crib into a daybed by following from
arefully s
Attach the ail to the footboard of the crib using t e supplied Allen bolts Start the thread by hand to assure you don't strip the threads, then, use the Allen wrench.
After completing , your crib should look like the one depicted on the first page of this instruction booklet.
C
toddler r h
tore the resulted pieces in a proper place, taking care not to scratch the wood finish.
the Allen bolts.
T.
“ASSEMBLY INSTRUCTIONS FOR YOUR 4501 CONVERTIBLE CRIB” (WR)
STEPS B & C STEP 2
but don’t attach the wooden rail listed in
. Adjust the mattress support to its lowest position (see for details)
away from direct sunlight and moisture,
Remember: the resulted hardware is not a toy!
You must keep this hardware in a proper place, away from your children.
HARDWARE BOX CONTENT
1
2
Please locate and confirm that
you have the following parts:
TR. toddler rail = 1
one bag of hardware with the following:
. Allen wrench =
. Allen bolt (60 mm - 2 3/8") = 3
1
2
1

#2 x 3
TR
FIGURE 1
WARNING!
COMPLETELY TIGHTEN!
FB

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.