Romina 11510 User manual

ASSEMBLY INSTRUCTIONS
FOR YOUR
11510 STATIONARY CRIB
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominafurniture.com
IMPORTANT: PLEASE, READ ALL
INSTRUCTIONS BEFORE
ASSEMBLING! PLEASE, SAVE
INSTRUCTIONS FOR FUTURE USE
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
WARNING: THE PROPER USE OF THIS CRIB IS IMPORTANT FOR
YOUR BABY'S SAFETY. TO KEEP YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH, CAREFULLY READ
AND FAMILIARIZE YOURSELF WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET. KEEP THIS
INSTRUCTION BOOKLET FOR FUTURE USE.
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION
this picture shows how your crib
should look like after completing assembly

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH OR
REGULAR BED.
*USE OFAVAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELLAND FINISH TO PEEL.
*DO NOT STORE CRIB INAREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME, SUCH
AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS MAY
CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN STRUCTURAL
FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE MANUFACTURER
WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR CLEANING WITH MILD
SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN A DRY CLOTH, WILL
PRESERVE THE ORIGINAL LUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OFACRIB WATER MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING
REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT
EVERY COMPONENT IS PROPERLY AND SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO YOUR
CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT ALL
BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST CHECK
ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS NECESSARY.
PERIODICALLY INSPECT CRIB FOR DAMAGED HARDWARE,
LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE TO
HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU MAKE
CONTACT. THE MODEL CODE CAN BE FOUND ON A WHITE LABEL
LOCATED ON THE INSIDE OF YOUR CRIB ON THE SIDE PANEL.

11510 BOX CONTENT Please locate and confirm that
you have the following parts:
EP.
SS.
MS.
end panel = 2
stationary side = 2
mattress support = 1
BF.
DL.
1.
2.
5.
6.
7.
8.
9.
Required tools:
CAUTION:
bottom frame = 1
decorative leg = 4
and one bag of hardware with the following:
Allen wrench =
one storage pouch and two plastic ties
rounded head bolt (30mm - 1 1/8") = 4
rounded head bolt (15mm - 5/8") = 4
"butterfly" type nut = 4
“internal star” lock washer = 26
“external star” lock washer = 8
Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
Do not use a power screwdriver which can
cause screws to break or strip.
1
3.
4.
Allen bolt (40mm - 1 5/8" - w/o centering tip) = 14
Allen bolt (20mm - 3/4" - w/o centering tip) = 12
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
printed in full size
1
Note:
TIGHTEN
During the assembly process whenever using screws or
bolts, check each by placing the screw / bolt on the hardware
diagram which is drawn in actual size. Be sure to use the proper
size and shape specified in the instructions. Be sure to
the screws / bolts when you are
asked to do this.
COMPLETELY
Note: The item number of your product is
located on the inner side of the left panel,
on a black and white label. Please, refer to
this number in the event that you need to
call ROMINA FURNITURE or your local
distributor. Thank you.
3
4
56
7
8
9
EP
EP
SS
SS
BF
DL
MS
Phillips screwdriver (not included)
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

FIGURE 1
STEP 1 (Two adults are required to complete this step)
(SS) (EP) (3) (8)Attach the stationary sides to the end panels using eight bigger Allen bolts , eight bigger washers
and theAllen key. Take care to insert the washer between the bolt and the stationary side vertical post!
Do not completely tighten the bolts at this step, you will be asked to do this later.
3x 8 8x 8
3+8
3+8
3+8
3+8
3+8
3+8
3+8
3+8
EP
SS
SS
EP
REQUIRED
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

FIGURE 2
STEP 2
REMINDER
(Two adults are required to complete this step)
(BF) (SS)
(EP) (3) (8)
(DL) 12
(4) 12 (8)
Completely tighten 14 (3+8) 12
(4+8)
14 12
8 (3+8)
6 (3+8)
12 (4+8)
Turn the crib upside down, taking care not to scratch its finish.
Attach the base frame to the stationary sides and to the end
panels using six bigger Allen bolts , six bigger washers and
the Allen key. Take care to insert the washer between the bolt and the
base frame wooden components!
Attach the decorative legs to the crib using smaller Allen bolts
, washers and the Allen key. Take care to insert the washer
between the bolt and the metallic plate!
all bigger Allen bolts and all smaller
Allen bolts used before.
Turn the crib in its normal position, taking care not to scratch its finish.
You have to completely tighten bigger Allen bolts and smaller
Allen bolts, distributed as following:
- bigger bolts in the stationary sides;
- bigger bolts in the base frame;
- smaller bolts in the decorative legs.
BF
DL
DL
DL
DL
3+8
4+8
3+8
3+8
3+8
3+8
3+8
4+8
4+8
4+8
4x 12 8x 12 3x 6 8x 6
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
WARNING:
VERY IMPORTANT
TIGHTEN 26
STEP 2.
TO KEEP YOUR BABY SECURE AND
SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S TO
ALL BOLTS LISTED
IN
COMPLETELY
REQUIRED
WARNING!
COMPLETELY TIGHTEN!

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger round head
bolts , 4
STEP 3 (One adult is required to complete this step)
(5) "butterfly" type nuts , 4 smaller lock washers
and a Phillips screwdriver (not supplied).
The lock washer must be attached to the bolt after the bolt
passed through the frame and the metallic bracket of the
mattress support and before attaching the nut.
There are three positions for the mattress support (from
the highest one for a newborn to the lowest one for a
child that is maximum 35" tall - see caution note). You
must adjust the height of the mattress support
depending of your child height by inserting all
four bolts in the same position (see ).
(7)
(9)
FIGURE 3
Do not completely tighten the bolts at
this step, you will be asked to do this later.
FIGURE 3
To adjust the vertical position of your mattress support you must remove the mattress support from the crib
remove all four bolts & nuts , lower the frame and insert the bolts back into
the corresponding holes, according to the desired height (see ). Then, you must attach the lock
washers and the nuts as described in , attach the mattress support to the crib
and tighten all the bolts.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(please see ),
(please see
) completely
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest position, the
mattress support frame must be placed directly over the bottom frame. Before tightening the bolts, you must
slightly press the mattress support frame to make sure this position is achieved.
TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH,
STEP 4
STEP
4
(5+9+7) (5)
FIGURE 3
(9) (7) STEP 3
WARNING:
IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (5+9+7) &
(6+9) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
5x 4 9x 4 7x 4
5+9+7
5+9+7
5+9+7
5+9+7
5+9+7
REQUIRED
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
WARNING!
COMPLETELY TIGHTEN!

FIGURE 4
STEP 4
REMINDER
(Two adults are required to complete this step)
(MS) (BF)
(6)
Completely tighten 8 (5+9+7, 6+9)
8
4 (5+9+7)
4 (6+9)
Attach the mattress support to the bottom frame using
four smaller rounded head bolts
all bolts involved in mattress
support fixing using a Phillips screwdriver (not supplied).
You have to completely tighten rounded head bolts, distributed
as following:
- bolts in the mattress support;
- bolts in the bottom frame.
A
After completing assembly, your crib should look like the one
depicted on the first page of this manual
, four smaller washers and
a Phillips screwdriver (not supplied). The lock washer must be
attached to the bolt before inserting the bolt through the metallic
bracket of the mattress support.
ttach the storage pouch supplied to the mattress support spring
using two plastic ties (also supplied). Store this instruction booklet
in the storage pouch for future use.
(9)
.
6+9
6+9
6+9
6+9
5+9+7
5+9+7
5+9+7
5+9+7
MS
WARNING!
COMPLETELY TIGHTEN!
5x 4 8x 4
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
WARNING:
VERY IMPORTANT
TIGHTEN
STEP .
TO KEEP YOUR BABY SECURE AND
SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S TO
ALL BOLTS LISTED
IN
COMPLETELY 8
4
REQUIRED

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
for updates, special offers and more new designs.
www.rominafurniture.com
Team
Thank you for being one of our distinguished clients.
Furniture