Romina 301 Nerva User manual

ASSEMBLY INSTRUCTIONS
FOR
3
YOUR
01 NERVA CRIB
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
WARNING:
.
THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY'S SAFETY. TO KEEP
YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE
DO NOT THROW THIS INSTRUCTION BOOKLET
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominakidsfurniture.com
Furniture
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
AND BY THE
AMERICAN SOCIETY FOR TESTING AND
MATERIALS
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINALLUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECUERLY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.

Please locate and confirm that
you have the following parts:
F. front panel = 1
B. back panel = 1
L. left panel = 1
R. right panel = 1
M. mattress support = 1
one bag of hardware with the following:
1. round head bolts (19/32" or 15 mm) = 4
2. Allen bolts (2 3/8" or 60 mm) = 10
3. one storage pouch and two plastic ties
4. Allen wrench = 1
5. round head bolts (1 3/16" or 30 mm) = 4
6. "butterfly" type nut = 4
7. bigger “internal star” lock washer = 10
8. smaller “external star” lock washer = 8
Required tools:
.
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included)
Do not use a power screwdriver which
can cause screws to break or strip
6
4
F
B
L
R
M
Note:
TIGHTEN COMPLETELY
During the assembly process whenever using screws or bolts, check
each by placing the screw / bolt on the upper diagram which is drawn in actual size.
Be sure to use the proper size and shape specified in the instructions.
Be sure to the screws / bolts when you are asked to do so.
The item
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number
in the event that you need to call
ROMINA FURNITURE or your local
distributor.
Note:
Thank you.
Note: The letter that identify
a part is the first letter of the
respective part name (such
method is employed to
facilitate parts recognition
between the drawings
and the parts list).
Phillips screwdriver (not supplied)
printed in full size
2
15
786
3
8
7

FIGURE 1
this shows how your crib should look
after completing STEP 1
STEP 1
Attach the right panel of your crib to the
back panel using 3 Allen bolts , 3
washers and the Allen wrench supplied
.
Do the same for the left panel .
(R)
(B) (2)
(7)
(4)
(L)
Do not tighten the bolts completely at this
step, you will be asked to do so later.
B
R
2
2
2
B
R
L
7
7
7

Assemble the result of with the front
panel using 4 Allen bolts ,
and the Allen wrench supplied .
STEP 2
STEP 1
(F) (2)
(4)
4 washers
(7)
Do not tighten the bolts completely at this
step, you will be asked to do so later.
FIGURE 2
this shows how your crib should look
after completing STEP 2
B
L
R
F
2
2
2
2
BR
LF
7
7
7
7

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger
round head bolts , 4
STEP 3
(5)
Do not tighten the bolts completely at
this step, you will be asked to do this later.
"butterfly" type nuts , 4
smaller lock washers and a Phillips screwdriver
(not supplied). The lock washer must be attached
to the bolt after the bolt passed through the frame
and the metallic bracket of the mattress support
and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see ).
(6)
(8)
FIGURE 3
NOTE: THE STYLE OF YOUR CRIB
OR OF YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION
SHEET
FIGURE 3
5
6
5
6
5
6
5
6
5
6
8
8
8
8
8
To adjust the vertical position of your mattress support you must remove all the four bolts & nuts
loosen all the four bolts , lower the frame and insert the bolts back into the corresponding holes,
according to the desired height (see ). Then, you must attach the lock washers and the nuts
as described in and tighten all the bolts completely.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(5+8+6),
(1+8) (5)
FIGURE 3 (8) (6)
STEP 3
ADJUSTED THE HEIGHT OF YOUR MATTRESS SUPPORT
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the inner wooden blocks. Before
tighten the bolts, you must slightly press the mattress support frame to make sure this position is
achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO TIGHTEN COMPLETELY ALL THE 8 BOLTS (5+8+6) &
(1+8) AFTER YOU HAVE .

Insert the mattress support into the crib and fix it
on the back panel through the wooden blocks
using 2 rounded head bolts , 2 washers and
the Phillips screwdriver (not supplied).
Fix the mattress support on the front panel
through the wooden blocks as described above.
STEP 4
(M)
(B)
(1) (8)
(F)
Tighten completely the four rounded head
bolts listed above.
The lock
washer must be attached to the bolt before inserting
the bolt through the metallic bracket of the mattress
support.
FIGURE 4
FLOOR
B
F
L
R
1
1
M
WARNING!
TIGHTEN COMPLETELY!
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE 4 BOLTS LISTED
IN .STEP 4
TIGHTEN THE SAME BOLTS ON
THE FRONT PANEL OF YOUR CRIB!
1
8
8
8

FIGURE 5
Turn your crib with its feet back on the floor.
STEP 5

U
STEP 6
tighten
completely (2+7)
FIGURE 6
(2+7) (B)
(2+7) (B)
(2+7) (L)
(2+7) (R)
all the Allen bolts remained untighten from
all previous steps (see ).
You have a total of 10 Allen bolts, distributed as following:
- 4 bolts in the bottom part of back panel ;
- 2 bolts in the upper part of back panel ;
- 2 bolts in the front of left panel ;
- 2 bolts in the front of right panel .
REMINDER
sing the Allen wrench supplied,(4) you must
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE 10 ALLEN BOLTS
LISTED IN .STEP 6
FIGURE 6
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
TIGHTEN THE SAME BOLTS ON
THE RIGHT SIDE OF YOUR CRIB!
2
2
2
2
2
2
2
2
2
2
7
7
7
7
7
7
7
7
7
7

this shows how your crib should look like after completing assembly
Once completed , attach the storage
pouch supplied to the mattress support
spring using two plastic ties (also supplied).
Store this instruction booklet in the storage
pouch for future use.
STEP 6

ASSEMBLY INSTRUCTIONS
FOR
3
DAY BED OPTION OF
YOUR 01 NERVA CRIB
WARNING (FOR DAY BED OPTION ONLY):
§
§
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN 50LB.
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
DO NOT THROW THIS INSTRUCTION BOOKLET.
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominakidsfurniture.com
Furniture

STEP A
Turn your crib and place it with the back
panel on the floor. Please, take care not to
scratch the finish of your crib.
completely all the 4 rounded
head bolts found on the back panel
and the front panel inside surfaces
(see ). Keep these bolts at your
hand for the following steps.
Remove the mattress support by
unscrewing
(M)
(1+8)
(B) (F)
FIGURE A
FIGURE A
STARTING FROM CRIB
B
1
1
L
R
F
M
FLOOR
8
8

STEP B
Remove all the 4 bigger round head bolts &
nuts located on your mattress
support, adjust this to it's lowest position
then all the 4 bolts &
nuts in their new position using a
Phillips screwdriver (not supplied).
(5+8+6)
tighten completely
(5+8+6)
For more
details about mattress support height
adjustment see
and
.
“ADJUSTING THE HEIGHT
OF YOUR MATTRESS SUPPORT”
FIGURE 3
FIGURE B
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE 4 BOLTS LISTED
IN .STEP B
WARNING!
TIGHTEN COMPLETELY!
5
6
5
6
6
5
5
6
5
6
5
6
5
6
5
6
this shows how your mattress support should look like
after completing STEP B
8
8
8
8
8
8
8
8

STEP C
Insert the mattress support as it was
adjusted at into the crib and fix it on the
back panel and the front panel using the
same tehnique described in .
(M)
STEP B
(B) (F)
STEP 4
Tighten completely
(1+8)
FIGURE C
the four rounded head
bolts involved in mattress support fixing
(see ).
FIGURE C
B
F
L
R
M
1
1
TIGHTEN THE SAME BOLTS ON
THE FRONT PANEL OF YOUR CRIB!
WARNING!
TIGHTEN COMPLETELY!
WARNING:
VERY IMPORTANT
TO KEEP YOUR
BABY SECURE AND SAFE, AND TO
AVOID POTENTIAL INJURY OR DEATH,
IT'S TO TIGHTEN
COMPLETELY ALL THE 4 BOLTS LISTED
IN .STEP C
8
8

STEP D
Using the supplied Allen wrench ,
unscrew completely the 4 Allen bolts and
washers (previously mounted in factory)
located 2 by 2 on the lateral sides of the
front panel . Then, remove the middle
panel resulted (see ). Store the
middle panel and the 4 Allen bolts resulted
in a proper place, taking care not to scratch
the panel.
(4)
(x)
(F)
FIGURE D
FIGURE D
x
x
x
x

this shows how your day bed should look like
after completing STEP D
STARTING FROM SCRATCH
§
§
FOLLOW FROM THE
CRIB ASSEMBLY INSTRUCTIONS.
WHEN YOU REACH , PLEASE
ADJUST YOUR MATTRESS SUPPORT TO
ITS LOWEST POSITION (YOU MUST
ALSO SEE FOR MORE
DETAILS).
FOLLOW FROM THE DAY BED
OPTION ASSEMBLY INSTRUCTIONS.
STEPS 1 TO 6
STEP 3
STEPS B & 3
STEP D
Please, store this instruction booklet in the
storage pouch for future use.

FULL SIZE BED OPTION OF
YOUR 01 NERVA CRIB3
NOTE:
CKC 301 C K
C 301 .
YOUR 301 NERVA CRIB CAN CONVERT INTO A
FULL SIZE BED WITH THE PURCHASE OF ROMINA
FURNITURE ITEM CODE ( ONVERSION IT
FOR RIBS, code )
ASSEMBLY INSTRUCTIONS FOR FULL SIZE BED
OPTION CAN BE FOUND INSIDE OF CKC PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.
NOTE: THE STYLE OF YOUR BED MAY VARY
FROM WHAT IS PICTURED IN THE INSTRUCTION
SHEET

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of this
fine finish of your Romina Furniture product.
Visit
for updates, special offers and more new designs.
www.rominakidsfurniture.com
Team
Thank you for beeing one of our distinguished clients.
Furniture