Rompa 19425 User manual

Page 1of 4Copyright ROMPA® Ltd
FLOATING COLOUR MIX SWITCH 19425, KH 10.10
FLOATING COLOUR MIX SWITCH 19425
CONTENTS
This product is supplied bagged and contains:
1 x Floating Colour Mix Switch
4 x AA batteries
Please note: this product requires, but does not include, a Wi Fi or everysense®product with
provision for its colours to change – see Specification below for a list of compatible products

Page 2of 4Copyright ROMPA® Ltd
FLOATING COLOUR MIX SWITCH 19425, KH 10.10
BEFORE USE
1. Locate the two battery holders on the short sides.
2. Twist open the tops and insert the batteries as shown.
Close the battery holders securely.
USE
1. This switch is wireless – it works from a distance and does not require direct connection to
the switch-activated product. Make sure that the product to be activated is plugged in, and

Page 3of 4Copyright ROMPA® Ltd
FLOATING COLOUR MIX SWITCH 19425, KH 10.10
where appropriate switch on. If there are multiple Wi Fi products in the room they will all
be activated.
2. Make sure the large rocker switch is switched ON (there is a large ON/OFF rocker switch
along one side).
3. Press the buttons on the top of the switch to control the colour of your switch-activated
product e.g. to change the colour of the bubble tube. For example, press the blue buttons
to turn your bubble tube more or less blue; the red button to turn it more or less red etc.
Mix colours or adjust their intensity.
4. Remember to turn the switch off after use.
5. Remember to take the switch out of the water after use. This allows the switch to dry out
thoroughly and avoids any potential damage caused by pool chemicals.
CARE & MAINTENANCE
Wipe clean with a very slightly damp clean cloth.
Avoid abrasive cleaning products which could scratch this product.
Do not attempt to open up the switch - there is no need to access the interior of the switch.
ALWAYS take the switch out of the water after use
Once this product is completely exhausted, please dispose of it appropriately.
SAFETY
Always supervise the use of this product.
TROUBLESHOOTING
In the unlikely event that your switch-activated product does not work with this switch, check:
•That this switch is ON and that the batteries are installed and do not need replacing
•That your switch-activated device is plugged in and set to ON if it has an ON/OFF button
SPECIFICATION
Built to IP65 rating
Power: 4 x AA batteries (included)
Size: 22cm long x 14.5cm wide x 5.5cmH
Moisture-resistant – usable in dry or wet environments
Compatible with:
Colour Changing Panel by ROMPA®19214
Colour Match Panel by ROMPA®19209
Light Source by ROMPA®19210 (and therefore Milky Way Carpet, Star Cloth, Fibre
Optics etc)
Fireworks Panel by ROMPA®18544 (purchased 2009 onwards)
Catherine Wheel Panel by ROMPA®19603 (purchased 2009 onwards)
Ball-Bubble Tubes by ROMPA®19767-70
Midi Bubble Tube by ROMPA®19771
Giant Maxi Bubble Tube by ROMPA®19776
Maxi Bubble Tubes by ROMPA®19772-5
Aquatic Bubble Tube by ROMPA®19777-80
Multitube Bubble Tube by ROMPA®19781
Tranquility by ROMPA®16049
Snoezette Unit by ROMPA®16046, 18120, 18709
The Vibro Tub by ROMPA®18549-50
Interactive ‘Talking’ Vibro Tub by ROMPA®18546, 19789
Mirrored Fibre Optic Light Panel by ROMPA®18539
Sparkling Carpet Panel by ROMPA®18542

Page 4of 4Copyright ROMPA® Ltd
FLOATING COLOUR MIX SWITCH 19425, KH 10.10
Interactive Fibre Optic ‘Fountain’ Panel by ROMPA®18537
Colour Wall Controller 19423
For further information about any of the above products please see www.rompa.com
This product meets the requirements of EN60950