Rompa 19424 User manual

Copyright ROMPA® Ltd
FLOATING COLOUR CHANGE SWITCH 19424, KH 8.10
FLOATING COLOUR CHANGE SWITCH 19424
CONTENTS
This product is supplied bagged and contains:
1 x Floating Colour Change Switch
1 x Battery charger
Please note: this product requires, but does not include, a Wi Fi or everysense®product with
provision for its colours to change – see Specification below for a list of compatible products
BEFORE USE
1. Charge the battery – see Care & Maintenance below.
2. Make sure the rubber cap covering the charging connector is properly closed.
USE
1. Turn ON the main switch.
2. This switch is wireless – it works from a distance and does not require direct connection to
the switch-activated product. Make sure that the product to be activated is plugged in, and

Copyright ROMPA® Ltd
FLOATING COLOUR CHANGE SWITCH 19424, KH 8.10
where appropriate switch on. If there are multiple Wi Fi products in the room they will all
be activated.
3. Press the coloured button clusters on the top of the switch to control the colour of your
switch-activated product e.g. to change the colour of the bubble tube. The button cluster
is large and could be activated by a foot, cheek, elbow etc – not just a hand. For example,
press the blue cluster to turn your bubble tube blue; the red button to turn it red etc.
4. If no buttons are pressed, all compatible Wi Fi products will revert back to their automatic
sequence after one minute.
5. Remember to turn the switch off after use.
6. Remember to take the switch out of the water after use. This avoids any potential damage
caused by pool chemicals.
CARE & MAINTENANCE
Wipe clean with a very slightly damp clean cloth
Avoid abrasive cleaning products which could scratch this product.
Do not attempt to open up the switch - there is no need to access the interior of the switch.
ALWAYS take the switch out of the water after use
Once this product is completely exhausted, please dispose of it appropriately.
Battery Charging
1. Use only the charger supplied to charge the battery.
2. Make sure the switch is turned OFF before charging.
3. Make sure the switch is dry and in a dry location before charging.
4. Connect the charger – please see images below.
5. Plug the battery charger into the wall socket and switch ON.
6. The battery will take 5½ hours to charger from flat.
SAFETY
Always supervise the use of this product.
TROUBLESHOOTING
In the unlikely event that your switch-activated product does not work with this switch, check:
•That this switch is ON
•That the battery is charged
•That your switch-activated device is plugged in and set to ON if it has an ON/OFF button

Copyright ROMPA® Ltd
FLOATING COLOUR CHANGE SWITCH 19424, KH 8.10
SPECIFICATION
Built to IP67 rating (‘protected from temporary immersion from 15cm to 1m for up to 30
minutes)
Size: 18cm long x 13cm wide x 6cmH
Weight: 650g
Battery: Ni-Mh 4.8v 500mA
Recharge from flat: 5½ hours
Estimated constant usage before charge required: 16 hours
Estimated intermittent usage before charge required: 5 days
Compatible with:
Colour Changing Panel by ROMPA®19214
Colour Match Panel by ROMPA®19209
Light Source by ROMPA®19210 (and therefore Milky Way Carpet, Star Cloth, Fibre
Optics etc)
Fireworks Panel by ROMPA®18544 (purchased 2009 onwards)
Catherine Wheel Panel by ROMPA®19603 (purchased 2009 onwards)
Ball-Bubble Tubes by ROMPA®19767-70
Midi Bubble Tube by ROMPA®19771
Giant Maxi Bubble Tube by ROMPA®19776
Maxi Bubble Tubes by ROMPA®19772-5
Aquatic Bubble Tube by ROMPA®19777-80
Multitube Bubble Tube by ROMPA®19781
Tranquility by ROMPA®16049
Snoezelen®Oasis 19096
Snoezette Unit by ROMPA®16046, 18120, 18709
The Vibro Tub by ROMPA®18549-50
Interactive ‘Talking’ Vibro Tub by ROMPA®18546, 19789
Mirrored Fibre Optic Light Panel by ROMPA®18539
Sparkling Carpet Panel by ROMPA®18542
Interactive Fibre Optic ‘Fountain’ Panel by ROMPA®18537
Colour Wall Controller 19005
Snow Panel 20132
For further information about any of the above products please see www.rompa.com
This product meets the requirements of EN60950