ROOMS TO GO HLVN A136-19 User manual

ASSEMBLY
INSTRUCTION
DUAL
POWER
RECLINER
HLVN A136 / A1360
Manufactured for Roo s To Go
HLVN
SKU
:
A136-19 15415602
A1360-19 11413604
LIST OF PARTS
NO. Description Item Qu ntity
A Backrest 1
B Seat 1
CWall plug
transfor er 1

ASSEMBLY INSTRUCTIONS
Step 1: Take out carefully the back cushions & seat fro the packing.
Step 2: Positing the fe ale etal receiver brackets over the ale etal posts. Push down the fe ale
brackets over ale posts si ultaneously until each side is locked into place an audile "click" is heard.
POWER CONNECTION
Step 3: Lift velcro flap located at the botto back. Latch ale wire plug fro backrest (headrest otor wire)
to fe ale wire receiver located at the botto back underneath the flap. This instruction is applicable to all
power headrest. Allow sufficient space between recliner and the wall behind it.
Step 4: Connect wall plug transfor er to transfor er switch.
And connect transfor er plug to electrical outlet.

ELECTRICAL CONTROLS
1 Press button to recline the recliner to desired position
2 Press button to raise the recliner to the upright position.
3 Press button to activate the headrest forward.
4 Press button to return headrest to the closed position.
WARNINGS
*
Keep
unit
at
least
6
"
fro
wall
.
*
Keep
unit
at
least
24
"
fro
all
heat
sources
.
* Avoid placing unit in areas where unit can be exposed to direct sunlight other powerful light sources, as
fading or discoloration ay occur.
*
Do
not
reach
under
seat
when
echanis
is
operating
or
serious
injury
ay
occur
.
*
Reclining
echanis
should
only
be
operated
while
seated
properly
.
*
Do
not
sit
on
ar s
or
backrest
.
*
Do
not
ju p
or
roughhouse
on
furniture
.
*
If
unit
ust
be
oved
,
do
not
drag
.
Unit
ust
be
lifted
in
order
to
be
oved
.
* Do not continuously operate echanis for ore than one inute or unit ay go into protection ode by
shutting down to prevent overheating.
*
Unplug
unit
fro
power
source
prior
to
cleaning
echanis
.
*
Do
not
allow
electrical
co ponents
to
co e
into
contact
with
any
liquids
.

CARE AND CLEANING
* Upholstered furniture is packaged tightly to protect it during transsit. This packaging can so eti es cause
creases or isshaped cushions when the furniture co es out of the packaging. These issues will correct
the selves over ti e as the fibers of the cushions are exposed to air. However, shaping the cushions with
your hands can alleviate the creases and co pressed fibers ore quickly.
* Use a vacuu cleaner to re ove dust and debris fro sea s and crevasses.
* Use a soft da p cloth to gently clean soiled areas and wipe clean. Do not rub.
* Do not use household cleaners or solvents. Such cleaners ay cause da age and/or discoloration.
* Do regularly use dedicated leather care product onto the leather furniture to prevent built up of body oils.
TROUBLE SHOOTING
PROBLEM SOLUTION
Headrest not working Ensure that wall power outlet is functional Step 4
Ensure that headrest power cable is plugged into the seat cable Step 3
Not Reclining Ensure that wall power outlet is opterational Step 4
Backrests gaps Ensure the backrests are properly clipped into the ale posts located on seat
echanis . Check that brackets are not loose, positioned i properly or bent.