Rose electronics VideoSplitter CAT5 User manual

CrystalView Plus USB
ENHANCED CAT5 KVM EXTENDER
10707 Stancliff Road Phone: 281) 933-
7673
Houston, Texas 77099 Internet: WWW.ROSE.COM
INSTALLATION AND OPERATIONS
MANUAL

LIMITED WARRANTY
Copyright Rose Electronics 2004. All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any
means, electronic or mechanical, including photocopying and recording, without the prior written permission
of Rose Electronics.
Rose Electronics Part # MAN-CRVPUSB
Printed In the United States of America – Revision 1.5
Rose Electronics
®
warrants the CrystalView Plus™ USB to be in good working order for one year
from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to
be in good working order at any time during this one-year warranty period, Rose Electronics will, at its
option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either
reconditioned or new. All replaced parts become the property of Rose Electronics. This limited
warranty does not include service to repair damage to the Unit resulting from accident, disaster,
abuse, or unauthorized modification of the Unit, including static discharge and power surges.
Limited Warranty service may be obtained by delivering this unit during the one-year warranty period
to Rose Electronics or an authorized repair center providing a proof of purchase date. If this Unit is
delivered by mail, you agree to insure the Unit or assume the risk of loss or damage in transit, to
prepay shipping charges to the warranty service location, and to use the original shipping container or
its equivalent. You must call for a return authorization number first. Under no circumstances will a unit
be accepted without a return authorization number. Contact an authorized repair center or Rose
Electronics for further information.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO
WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE
REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL
ROSE ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST
PROFITS, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OF OR THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE
ELECTRONICS OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY
TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
IBM, AT, and PS/2 are trademarks of International Business Machines Corp. Microsoft and Microsoft
Windows are registered trademarks of Microsoft Corp. Any other trademarks mentioned in this
manual are acknowledged to be the property of the trademark owner.

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY
FEDERAL COMMUNICATIONS COMMISSION
AND INDUSTRY CANADA
RADIO-FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses and can radiate radio frequency energy
and if not installed and used properly, that is in strict accordance with the
manufacturer’s instructions may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A digital
device in accordance with the specifications of Part 15 of FCC rules, which
are designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which
case the user at his own expense will be required to take whatever
measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise
emission from digital apparatus set out in the Radio Interference Regulation
of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe A
prescrites dans le Règlement sur le brouillage radioélectrique publié par
Industrie Canada.

EUROPEAN UNION DECLARATION OF CONFORMITY
ACCORDING TO COUNCIL DIRECTIVE 89/336EEC & 73/23EEC
This equipment is in conformity with the
protection requirements of the following
Council Directives:
The Declaration of Conformity is based upon
compliance of the product with the following
harmonized standards:
EN55022: Class A
EN55024

TA LE OF CONTENTS
Contents
Disclaimer ...................................................................................................... 1
System introduction ....................................................................................... 1
Features.................................................................................................... 2
Compatibility ............................................................................................. 3
Package contents ..................................................................................... 3
Dual video Local models................................................................................ 4
Dual video Remote model ............................................................................. 5
Cables ............................................................................................................ 6
Serial cable ............................................................................................... 6
Audio cable ............................................................................................... 6
Installation ...................................................................................................... 8
Connecting the cables .............................................................................. 9
Keyboard commands.............................................................................. 11
Keyboard command descriptions ........................................................... 12
Local unit Keyboard commands ............................................................. 15
Adjusting the video ................................................................................. 16
Operating instructions- All units ................................................................... 19
Operating instructions .................................................................................. 19
KVM Switching........................................................................................ 19
Private mode........................................................................................... 19
Troubleshooting ........................................................................................... 22
Service Information ...................................................................................... 24
Maintenance and Repair......................................................................... 24
Technical Support ................................................................................... 24
Safety ........................................................................................................... 25

Figures
Figure 1. Dual Video Local models) ............................................................. 4
Figure 2. Dual Video Remote models) ......................................................... 5
Figure 3. Dual Video Connections................................................................. 9
Figure 7. Color skew delay compensation................................................... 16
Figure 8. Video Test Card............................................................................ 17
Figure 9 HF / LF adjustment guide. ............................................................. 17
Tables
Table 1. Keyboard Commands.................................................................... 11
Table 2. Channel select ............................................................................... 12
Table 3. Private mode commands............................................................... 19
Appendices
Appendix A. General specifications............................................................. 27
Appendix B. Parts and cables ..................................................................... 29
Appendix C. Rack mount instructions.......................................................... 30
Appendix D. Rack mount illustration............................................................ 30
Appendix E. Quick Installation/Setup Guide................................................ 31

INTRODUCTION
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
1
Disclaimer
While every precaution has been taken in the preparation of this manual, the
manufacturer assumes no responsibility for errors or omissions. Neither
does the manufacturer assume any liability for damages resulting from the
use of the information contained herein. The manufacturer reserves the
right to change the specifications, functions, or circuitry of the product
without notice.
The manufacturer cannot accept liability for damages due to misuse of the
product or other circumstances outside the manufacturer’s control. The
manufacturer will not be responsible for any loss, damage, or injury arising
directly or indirectly from the use of this product.
System introduction
Thank you for choosing the Rose Electronics

CrystalView Plus USB
enhanced KVM station extender. The CrystalView Plus USB is the result of
Rose Electronics commitment to providing state-of-the-art solutions for
today’s demanding workplace. The CrystalView Plus USB has proven to be
a valuable investment for any business, big or small, that has a need to
access CPUs from Remote locations.
The CrystalView Plus USB is available in a single or dual video model.
Serial/Audio features are also an option on all models. The single and dual
video models have local and remote access. The local access allows an
additional KVM station to be connected to the Local Unit.
The CrystalView Plus USB system consists of two Units, a Local Unit and a
Remote Unit. The Local Unit connects to your CPU with one or two video
sources or to a Rose switch. The Remote Unit connects to a USB keyboard,
one or two video monitors and a USB mouse. The Local and Remote Units
are connected together with industry standard CAT-5, CAT-5e, or CAT-6
shielded or unshielded, solid core twisted-pair cable terminated with RJ45
connectors. All models can extend the distance from the CPU up to 1,000
feet. CAT-x cable can be ordered from Rose Electronics in 25-1,000 foot
lengths.
Using the CrystalView Plus USB to remotely access your computer has
several applications that make it convenient for the users. You can locate
your computers in a secure area and access them from other unsecured
areas. Computers used in hazardous industrial environments can be
accessed remotely, keeping the users safe and unexposed to any hazards.

2
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Features
 Available in single and dual video models
 Extend a KVM station from a CPU using a single CAT-x cable. Up to
650 feet at resolutions of 1600 x 1200 @ 60Hz,
1,000 feet for the resolutions of 1280 x 1024 @ 75Hz.)
 Supports Serial, and full stereo audio
 Compatible with any USB 1.1 or 2.0 host
 Supports a maximum of 7 USB devices including USB hubs
 The CrystalView Plus USB uses a microprocessor to emulate the
keyboard and mouse for plug and play operation. The keyboard and
mouse on the Remote Unit do not have to be connected for the PC to
boot; only the Local Unit must be connected to the PC
 Integrated skew compensation adjusts all colors
 Low frequency LF) and high frequency HF) equalization adjustments
for optimum video tuning
 Compatible with Rose Electronics family of KVM switches such as
ServeView Pro, UltraView Pro and UltraMatrix
 Compatible with Windows, Windows NT, OS/2, Unix, Linux and other
operating systems
 Fully automatic KVM sharing on a first-come first-serve basis
 The computers video is displayed on both the local and remote KVM
stations monitors except in the private mode
 Local or Remote KVM station can inhibit the other
 Serial and Bi-directional full stereo audio options. Stereo audio can be
transmitted in either direction across the CAT-x link simultaneously
 Many serial devices like a Touchscreen can plug directly into the
Remote Unit
 Status indicator LEDs on each RJ45 connector
 Surge protection on each RJ45 port
 All settings and video tuning performed from the remote unit and saved
in flash memory
 Remote unit is flash upgradeable
 Rack mount kits available in 19”, 23” and 24” sizes

CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
3
Compatibility
Computers PCs with standard USB keyboards and
USB mice
Monitors VGA to UXGA
HV, Composite, Sync-on-green,
Keyboards USB type keyboard.
Mouse USB Wheel mouse
Serial Devices
Serial/Audio model
only)
Touchscreens, Graphic Tablets,
Serial printers/plotters, Computer terminals
Serial mice, Other standard asynchronous
serial devices.
Audio Devices
Serial/Audio model
only)
Compatible sound cards
Amplified or non-amplified microphone
Amplified computer stereo speakers
Other audio devices that transmit/receive
signals less than 5 volts peak-to-peak.
USB Devices
7 maximun)
Composite keyboard/mouse devices
PS/2 to USB converters
USB Hubs
Package contents
The package contents consist of the following:
 The CrystalView Plus USB Units as ordered
 Power adapter for Remote Unit. Auto-switching transformer)
 Gender changer factory installed)
 Installation and operations manual.
Video, serial, audio and CAT-x cables are usually ordered separately.
Rose Electronics web site
Visit out web site at www.rose.com for additional information on the
CrystalView Plus USB and other products that are designed for data center
applications, classroom environments and other applications.
About this manual
This manual covers the installation and operation of the CrystalView Plus
USB, single and dual video models.

MODELS
4
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Dual video Local models
Front view
Rear view
Figure 1. Dual Video Local models)
Connectors:
Front
 RJ45 2) CATx cable connection front panel)
Rear
 HD15F CPU video connection.
2) to CPU Video card / 2) to local monitors
 USB USB Type B
NOTE: The CrystalView Plus USB is available with single or dual video,
Local KVM access, and serial / audio options

CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
5
Dual video Remote model
Front view
Rear view
Figure 2. Dual Video Remote models)
Connectors:
Front
 RJ45 CATx cable connection front panel)
Rear Remote
 HD15F 2) KVM video connection.
 USB 4) USB Type A
Keyboard / mouse / USB device or hub connections
 Power 5V power adapter connector

CA LES
6
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Cables
Local Unit to CPU cables
Video - HD15MM cable for each CPU video output 1 or 2)
USB – Standard USB Type B to Type A
Remote Unit to KVM station cable
The USB keyboard, video monitor, and USB mouse cables on the remote
KVM station can connect directly to the CrystalView Plus USB Remote unit
Stereo speakers and a microphone can also connect directly to the remote
unit’s audio ports.
Local Unit to Remote Unit cable
The Local Unit is connected to the Remote Unit with up to 1,000 feet of
standard CAT-x UTP/STP “solid core” cable terminated with RJ45M
connectors. Rose Electronics cable part number CAB-08UTPnnn.
The unit uses two CAT-x cables from the local unit to the remote unit.
Serial cable
To connect the Local Unit to the CPUs DB9 serial port, you can use a
standard DB9MF serial 1:1 DTE-DCE) cable. The Remote Units “SERIAL”
port is wired as DTE the same as the CPUs serial port). To connect a serial
printer or other DTE devices to the Remote Unit, you will need a Null-
modem crossover) cable between the Remote Unit and the device. Select
Xon/Xoff software flow control on the printer and PC. A serial Touchscreen
can be directly connected to the Remote unit’s serial port.
Audio cable
CrystalView Plus USB models with the audio option are configured with two
3.5mm stereo audio jacks on both the Local and Remote Unit. Standard
3.5mm stereo audio cables can be used to connect between the Local Unit’s
“LINE IN” connector and a sound card’s “LINE OUT” connector. The
Remote Units “LINE OUT” connects to a pair of powered computer
speakers.

CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
7
If you want to use a microphone on the remote unit, there are two ways to
set this up:
1. Method #1
a) Connect the “LINE OUT” connector on the local unit to the “MIC”
input on the CPUs sound card
b) Connect a microphone to the remote units “LINE IN” connector
c) Adjust the sound card to provide an additional +20dB of
amplification.
2. Method #2 use the Remote unit for additional amplification)
a) Remove the Remote units power and cover and locate the jumper
labeled “MIC” and connect a jumper across the pins
b) Replace the Remote units cover and restore power
c) Connect a non-powered microphone to the Remote units “LINE IN”
connector and the Local units “LINE OUT” to the CPUs sound cards
“MIC IN” connector.
NOTE: If you are using a powered microphone, connect it directly to the
“LINE IN” connector on the remote unit and connect the Local units “LINE
OUT” connector to the sound cards “LINE IN” connector DO NOT INSTALL
THE “MIC” JUMPER)
The video performance will vary with different cable types. The CrystalView
Plus USB makes it easy to adjust the skew and video compensation with
simple keyboard commands.

INSTALLATION
8
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Installation
Please refer to the safety section first before proceeding with any installation
or configuration of the CrystalView Plus USB.
Installation of the CrystalView Plus USB consists of three easy steps.
1. Connect the cables to the equipment.
2. Applying power.
3. Adjust the video channels if needed).
More advanced users can refer to Appendix E for a quick installation and
video compensation adjustment guide.
For systems that only require running Video through the CrystalView Plus
USB with no keyboard or mouse or use extended cable lengths between the
local unit and a computer or KVM switch, supplemental power should be
supplied to the Local Unit. The Local Unit gets its power from the USB port
of the CPU. Rose Electronics can supply a power transformer that connects
to the Local Unit to provide this power. This power transformer can be
ordered from Rose Electronics P/N TFR-05D400FSUB)
When installing the CrystalView Plus USB, locate the Local unit as close as
possible to the CPU. Keep the USB and video cables as short as possible
but still give some freedom of movement. Using shorter cables keeps the
video noise to a minimum and reduces installation costs. You can mount
the CrystalView Plus USB in a CPU rack with the optional rack shelf kit.
When mounting in a rack, follow the instructions in Appendix C and
Appendix D and assure that the operating temperature of the Local and
Remote Units do not exceed the maximum ratings. Provide adequate air
circulation to assure that the maximum operating temperature is not
exceeded.
Wherever the CrystalView Plus USB Local and Remote Units are located,
they should be on a secure surface and free from obstructions and objects
that may cause damage to the units.

CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
9
Connecting the cables
Figure 3. Dual Video Connections
Local unit to CPU cabling
Use standard HD15MM cables to connect the primary and secondary video
outputs from the video card to the local unit’s HD15F connectors. A type A
to Type B USB cable connects from the computer to the units Type A
connector. Connect a primary and secondary monitor to the HD15F
connectors for local viewing of both video signals. For local access to the
computer, connect a USB keyboard and USB mouse to any available USB
port on the computer.
Remote Unit to KVM Station cabling
The USB keyboard and USB mouse connect directly to the CrystalView Plus
USB remote unit. The primary and secondary video monitors also connect
directly to the unit.
Serial/audio models
For the serial/audio models, connect the serial DB9M port on the CPU to the
DB9F serial connector on the CrystalView Plus USB using a DB9F to DB9M
serial cable.
The line out of the CPU’s sound card connects to the Line in port on the
CrystalView Plus USB. The line in connects to the CrystalView Plus USB
line out port.
Connect to the remote unit a pair of stereo speakers to the line out port, a
microphone to the line in port, and a compatible serial device to the DB9
connector.
LOCAL REMOTE
KVM STATION
CATx CA LE
Dual Video +
US connection

10
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Serial port
The serial port is a DB9F on the local unit and DB9M on the remote unit.
The serial port on the remote unit is the same as the DB9M serial connector
on your computer. Serial devices such as Touchscreens can connect
directly to the serial port on the remote unit
.
Audio ports
A set of powered computer speakers can connect directly to the CrystalView
Plus USB remote unit’s line level audio out connector. A powered or non-
powered microphone can connect to the Line level audio in MIC) connector.
If you are using a non-powered microphone on the Remote Unit, install the
“MIC” jumper, if needed, to provide additional amplification.
Applying power
(All models)
Plug in the power adapter to a 100/240-volt source and to the power
connector on the Remote Unit. Only use the power adapter provided
with the CrystalView Plus USB. Boot up the connected CPU and wait for
it to completely boot-up. The Local Units power is supplied from the
CPUs USB port. If additional power is required at the local unit due to
extended cable lengths or only passing video through the CrystalView
Plus USB, connect the optional +5V DC power adapter to the local units
+5V DC power jack.
With power applied, you should see the primary and secondary video on
the remote unit’s monitors. Verify that the keyboard and mouse
connected to the remote unit function properly. The video can be fine
tuned to correct for patch panels and cable differences with simple
keyboard commands. Table 1 shows the keyboard commands and key
sequences used to initiate the command.
DO NOT
INSTALL THE “MIC” JUMPER IF USING A
POWERED MICROPHONE.

KEY OARD COMMANDS
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
11
Keyboard commands
Note: Use only the numeric keys above the keyboard to initiate the keyboard
commands from the remote unit. Do not use the numeric keypad.
NOTE: All keyboard commands are initiated from the Remote unit.
Before any keyboard command can be issued, the unit must
be in the command mode and a channel selected.
Command Key Sequence
Command Mode [L-Ctrl] + [L-Shift] + [F10]
Exit Command Mode and save [ESC]
Exit Command Mode without saving [L-Shift] + [ESC]
Select Channel 1or 2 [1] / [2]
Select Channel 0 [0] select all channels)
Reset EQ & Delay values [L-Ctrl] + [Home]
Next Assisted EQ setting [L-Ctrl] + [PgUp]
Previous Assisted EQ setting [L-Ctrl] + [PgDn]
Increase RED delay [R] + [R-arrow]
Decrease RED delay [R] + [L-arrow]
Increase Green delay [G] +[R-arrow]
Decrease Green delay [G] + [L-arrow]
Increase Blue delay [B] + [R-arrow]
Decrease Blue delay [B] + [L-arrow]
Toggle RED delay [L-Ctrl] + [R]
Toggle GREEN delay [L-Ctrl] + [G]
Toggle BLUE delay [L-Ctrl] + [B]
Reset EQ values [L-Ctrl] + [End]
Increase LF EQ Course) [L] + [Up Arrow]
Decrease LF EQ Course) [L] + [Dn Arrow]
Increase LF EQ Fine) [L] + [R-Arrow]
Decrease LF EQ Fine) [L] + [L-Arrow]
Increase HF EQ Course) [H] + [Up Arrow]
Decrease HF EQ Course) [H] + [Dn Arrow]
Increase HF EQ Fine) [H] + [R-Arrow]
Decrease HF EQ Fine) [H] + [L-Arrow]
Reset keyboard and mouse [F1]
Send NULL mouse byte [F3]
Reset to factory defaults [L-Ctrl] + [F9]
Toggle Unit Private Mode [Scroll Lock]
Table 1. Keyboard Commands

12
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Keyboard command descriptions
Command mode – [L-Ctrl] + [L-Shift] + [F10]
Entering the command mode sends the remote units keyboard instructions
to the CrystalView Plus USB Local unit instead of the connected computer.
In the command mode, the yellow LED on the remote units RJ45 connector
for channel 1 will light indicating that the unit is in the command mode. The
keyboard status LEDs Num lock, Caps Lock, and Scroll Lock) will flash
indicating which channel is selected. The Command mode automatically
times out after 30 seconds of inactivity, saves all settings, and returns the
keyboard to normal functions.
Number of keyboard
status LED flashes Video channel selected
1 Channel 1 Default, all models)
2 Channel 2
Slow flashes Channel 0 All channels)
Table 2. Channel select
Exit Command mode and save – [Esc]
Pressing the Esc key while in the command mode will save all configuration
changes made and exit the command mode.
Exit Command mode without saving – [L-Shift] + [ESC]
Pressing the left shift key and the Esc key while in the command mode will
exit the command mode without saving any configuration changes.
Select Channel 1 – [1]
Pressing 1 while in the command mode selects channel one and all
configuration adjustments apply to channel 1 only. Keyboard status LEDs
flash once.
Select Channel 2 – [2]
Pressing 2 while in the command mode selects that channel and all
configuration adjustments apply to the selected channel only. Keyboard
status LEDs flash twice for channel 2.
Select Channel 0 – [0] Dual video model only)
Pressing 0 zero) while in the command mode selects all channels and all
configuration adjustments are applied to all channels.
This is especially helpful if all cable lengths and types used for all channels
are the same.

CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
13
Reset EQ & Delay values – [L-Ctrl] + [Home]
Issuing this command resets the LF and HF equalization and the red, green,
and blue delay values for the selected channel.
Next Assisted EQ setting – [L-Ctrl] + [PgUp]
This command resets the LF and HF equalization settings, then each time
the command is issued, incrementally steps through a table of preset LF
and HF equalization values for different cable lengths in 25m increments
from 0 to 375m. After finding the best setting, fine tuning of the HF and LF
equalization may be needed. Perform the fine tuning after adjusting for any
color skew.
Previous Assisted EQ setting – [L-Ctrl] + [PgDn]
This command decreases the LF and HF equalization settings by 25m. Use
this command in conjunction with the Next Assisted EQ setting command to
obtain the best setting for the select channel.
Increase RED delay – [R] + [R-Arrow]
Each time this command is issued, the RED video component is delayed an
incremental step from 0 to 42ns max. in 2.8 ns steps.
Decrease RED delay – [R] + [L-Arrow]
Use this command along with the increase RED delay to properly align the
RED video component.
Increase GREEN delay – [G] + [R-Arrow]
Each time this command is issued, the GREEN video component is delayed
an incremental step from 0 to 42ns max. in 2.8 ns steps.
Decrease GREEN delay – [G] + [L-Arrow]
Use this command along with the increase GREEN delay to properly align
the GREEN video component.
Increase LUE delay – [B] + [R-Arrow]
Each time this command is issued, the BLUE video component is delayed
an incremental step from 0 to 42ns max. in 2.8 ns steps.
Decrease LUE delay – [B] + [L-Arrow]
Use this command along with the increase BLUE delay to properly align the
BLUE video component.
Toggle RED delay – [L-Ctrl] + [R]
Each time this command is issued, the RED video component delay is
toggled between 0 and 19ns.

14
CRYSTALVIEW PLUS USB INSTALLATION AND OPERATIONS MANUAL
Toggle GREEN delay – [L-Ctrl] + [G]
Each time this command is issued, the GREEN video component delay is
toggled between 0 and 19ns.
Toggle LUE delay – [L-Ctrl] + [B]
Each time this command is issued, the BLUE video component delay is
toggled between 0 and 19ns.
Refer to Figure 6 for LF and HF adjustments)
Reset EQ values – [L-Ctrl] + [End]
Issuing this command will reset the HF and LF equalization values for the
selected video channel to zero. Color delay values are not affected.
Increase LF EQ (Course) – [L] + [Up Arrow]
Use the Increase LF EQ adjustment to remove black smears to the right of
large objects.
Decrease LF EQ (Course) – [L] + [Dn Arrow]
Use the Decrease LF EQ adjustment along with the Increase LF EQ to
obtain the sharpest image.
Increase LF EQ (Fine) – [L] + [R-Arrow]
Use the Increase LF EQ adjustment to remove black smears to the right of
large objects.
Decrease LF EQ (Fine) – [L] + [L-Arrow]
Use the Decrease LF EQ adjustment along with the Increase LF EQ to
obtain the sharpest image
Increase HF EQ (Course) – [H] + [Up Arrow]
Use the Increase HF EQ adjustment to sharpen the image.
Decrease HF EQ (Course) – [H] + [Dn Arrow]
Use the Decrease HF EQ adjustment along with the Increase LF EQ to
obtain the sharpest image.
Increase HF EQ (Fine) – [H] + [R-Arrow]
Use the Increase HF EQ adjustment to sharpen an image.
Decrease HF EQ (Fine) – [H] + [L-Arrow]
Use the Decrease HF EQ adjustment along with the Increase LF EQ to
obtain the sharpest image.