Rose electronics RackView RV1-CAKVT21L/DVI/Kn User manual

RackView
Sideways
Sliding
KVM Drawer - 21” (1920 x 1080) and 24” (1920 x 1200)
Installation
and
Operation Manual
10707 Stancliff Road
Houston, Texas 77099
Phone: [phone]
[email protected]

LIMITED WARRANTY
Copyright Rose Electronics 2018. All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and
recording, without the prior written permission of Rose Electronics.
manual-rackview-sideways-2018-03-28
Rose Electronics®warrants the RackView Sideways KVM Drawer to be in good working order for one year
from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good
working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or
replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All
replaced parts become the property of Rose Electronics. This limited warranty does not include service to
repair damage to the Unit resulting from accident, disaster, abuse, or unauthorized modification of the Unit,
including static discharge and power surges.
Limited Warranty service may be obtained by delivering this unit during the one-year warranty period to Rose
Electronics or an authorized repair center providing a proof of purchase date. If this Unit is delivered by mail,
you agree to insure the Unit or assume the risk of loss or damage in transit, to prepay shipping charges to the
warranty service location, and to use the original shipping container or its equivalent. You must call for a return
authorization number first. Under no circumstances will a unit be accepted without a return authorization
number. Contact an authorized repair center or Rose Electronics for further information.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO A
PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS
OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE
REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL ROSE
ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS, LOST
SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR
THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER
PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE.

DECLARATIONS OF CONFORMITY
This is to certify that, when installed and used according to the instructions in this manual, the units listed and
described here are shielded against the generation of radio interferences in accordance with the application of
Council Directives 2014/30/EU and 2014/30/EU, as well as these standards:
■EN 55022: 2010/AC:2011 (Class B)
■EN 55024:2010 + A1:2015
This equipment has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at their own expense.
This equipment fully complies with the requirements of European Union Regulation (EC) 1907/2006
concerning the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH):
These devices comply with Directive 2011/65/EU of the European Parliament and of the council of 8 June
2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS 2, RoHS II). The device labels carry a respective marking.

TABLE OF CONTENTS
Contents
Disclaimer 1
System Introduction 1
Features 1
Package Contents 2
RackView Options 2
RackView Model 3
Front View - All Models 3
RackView Product Layout 3
RackView Rear Panel Connector Layout 4
RackView Left-Side and Right-Side Models 4
Installation Procedure 5
Installation of the RackView Sideways 5
Operation of the RackView Sideways 6
Cabling RackView to an External Device 7
Connection to a USB Server/CPU 7
Connection to an External KVM Switch 7
RackView Cables 8
RackView Operation 9
Power-On Procedure 9
Video Input Select Button 9
OSD Selection 9
OSD Operation 10
Picture in Picture and Picture by Picture Modes (PIP and PBP) 11
Troubleshooting 12
Safety 13
Maintenance and Repair 14
Technical Support 14
Figures
Figure 1. RackView Sideways Models 3
Figure 2. RackView product layout - key features 3
Figure 3. RackView rear panel connector layout 4
Figure 4. RackView with left-side or right-side opening 4
Figure 5. RackView installation procedure 5
Figure 6. RackView console drawer operation 6
Figure 7. RackView cable connectivity 7
Figure 8. RackView device interface cables 8
Figure 9. OSD menu selection 9
Figure 10. RackView OSD configuration and settings 10
Figure 11. PIP and PBP configuration 11
Figure 12. PIP and PBP settings and operation 12
Figure 13. RackView chassis dimensions (21" model) 17
Figure 14. RackView chassis dimensions (24" model) 18

TABLE OF CONTENTS
Figure 15 RackView integrated KVM switch models 19
Figure 16. RackView with HDMI video option 20
Figure 17. HDMI cable connection 20
Figure 18. RackView with the 3G/HD/SD-SDI video option 20
Figure 19. RackView with a DC power connector fitted 22
Tables
Table 1. RackView product and packaging dimensions ................................................................... 17
Table 2. RackView product and packaging dimensions (including a KVM switch)............................. 17
Table 3. Video resolution related to LCD specification .................................................................... 19
Table 4. DVI-D and VGA video formats............................................................................................ 21
Table 5. 3G/HD/SD-SDI video formats ............................................................................................ 21
Table 6. RackView DC power options.............................................................................................. 22
Appendices
Appendix A —Specifications 15
Appendix B —Part Numbers 16
Appendix C —RackView Dimensions 17
Appendix D —RackView with Integrated KVM Switch 19
Appendix E —RackView Video Options 20
Appendix F —RackView DC Power Options 22

INTRODUCTION
RackView Sideways (21" and 24") Manual 1
Disclaimer
While every precaution has been taken in the preparation of this manual, the manufacturer assumes no
responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting
from the use of the information contained herein. The manufacturer reserves the right to change the
specifications, functions, circuitry of the product, and manual content at any time without notice.
The manufacturer cannot accept liability for damages due to misuse of the product or other circumstances
outside the manufacturer’s control. The manufacturer will not be responsible for any loss, damage, or injury
arising directly or indirectly from the use of this product (See limited warranty).
System Introduction
Thank you for choosing the Rose Electronics RackView Sideways Console Drawer. This product is available in
two models; the 21" HD (1920 x 1080) and the 24" ultra-high resolution (1920 x 1200). The RackView is the
ideal product for managing one or more PC’s/Servers in a confined rack space.
RackView Sideways offers the latest and most efficient way to organize and streamline your server rooms or
multiple computers. Since the display is wider than a standard 19" rack, the rack mountable KVM station pulls
out via its slide rails and the hinged display opens at right angles to the rack. The easy-glide KVM station
contains a high-resolution bright active matrix TFT display that provides crisp images at up to 1920×1200, wide
viewing angles, a tactile keyboard, and a 2-button touchpad mouse or trackball.
There are several options available with the RackView Sideways, including the integration of a VGA/USB or
DVI/USB KVM switch for PC/Server management, providing an all-in-one console management solution.
The instructions in this manual assume a general knowledge of computer installation procedures, familiarity
with cabling requirements, and some understanding video display device operation.
Features
■Fold-forward LCD display, keyboard, and mouse in a 1U sliding rack-drawer package
■21" HD resolution up to 1920 x 1080, and 24" ultra-high resolution up to 1920 x 1200, VGA or DVI
■Front panel controls provide access to the OSD for set-up and quick adjustments of
color, brightness, contrast, position, and shape of the display
■USB or PS/2 touchpad/keyboard interface
■Full size 104 keyboard with a separate numeric keypad and a 2-button touchpad mouse
■Supports Windows, Linux, Unix, Sun, MAC OS
■Panel protected by tempered glass
■Active EDID monitor function
■The RackView drawer can be mounted at any height in a standard 19" rack
■Fold, tilt, and slide the LCD Monitor for optimum viewing position
■18 International keyboard versions available
■Mounting rails included
■Optional DVI/USB or VGA/USB KVM Switch

RackView Sideways (21" and 24") Manual 2
Package Contents
The RackView package contents consist of the following:

1 x RackView Sideways sliding KVM drawer

1 x Mounting bracket (sliding rails) set

1 x Set of screws/washers for assembly

1 x Combo interface cable (depending on the model selected)

1 x Power supply unit

1 x Power cable

1 x Manual
The above package content is only for the single console model. The contents can vary with options such as a
KVM switch, HDMI and 3G/SDI video and DC power.
Additional cables are usually ordered separately. If the package contents are not correct, contact Rose
Electronics or your reseller so the problem can be quickly resolved.
RackView Options

Integrated KVM switch, DVI USB Audio (12 port) or VGA USB (8 or 16 port)

HDMI (replaces the DVI interface)

3G/HD/SD-SDI video

PIP and PBP display options on the 24" ultra-high resolution model only

Front USB 2.0 port for device access, available with the KVM-Hub switch option only

Trackball mouse

DC power, 12, 24, 48, 125, 250V
Before Installation
It is very important to mount the equipment in a suitable cabinet or on a stable surface.
Make sure the mounting location has good ventilation, is out of direct sunlight, and away from sources of
excessive dust, dirt, heat, water, moisture, and vibration.

MODELS
RackView Sideways (21" and 24") Manual 3
RackView Model
The RackView is available as described below.
Front View - All Models
RackView Sideways 21-inch color LCD RackView Sideways 24-inch color LCD
Figure 1. RackView Sideways Models
RackView Product Layout
RackView Sideways Product Layout
Figure 2. RackView product layout - key features

RackView Sideways (21" and 24") Manual 4
RackView Rear Panel Connector Layout
The RackView rear panel includes an HD15(KB/MS) and DVI-D connector as standard. The HD15(KB/MS)
connector supports VGA video, and also the keyboard/mouse interface.
This diagram shows the approximate positioning of the DVI-D and KB/MS connectors on the rear panel.
Figure 3. RackView rear panel connector layout
RackView Left-Side and Right-Side Models
Figure 4. RackView with left-side or right-side opening
Select the RackView Sideways as either a left-side or right-side opening rack drawer to best fit the ergonomics
of your rack room. The rack mountable KVM drawer smoothly pulls out upon its slides and the hinged display
opens at right angles to the rack.
Add an [ L ] or [ R ] to the product part number to indicate the opening/sliding design of the RackView
.

INSTALLATION
RackView Sideways (21" and 24") Manual 5
Installation Procedure
Installation of the RackView Sideways
Step 1
Insert the Left and Right rear-mounting slides into
the RackView Console Drawer
Step 2
Measure the depth of the front and rear rack rails
Align each rear-mounting slide to a suitable length
(depth)
Step 3
Complete the Installation
Fix the RackView Console Drawer into the Rack
A set of mounting accessories is provided
Figure 5. RackView installation procedure

RackView Sideways (21" and 24") Manual 6
Operation of the RackView Sideways
Step 1
Hold the handle and slide out the RackView drawer
Step 2
Flip up the LCD to a suitable viewing angle
Step 3
Operate the RackView Console Drawer
Figure 6. RackView console drawer operation

RackView Sideways (21" and 24") Manual 7
Cabling RackView to an External Device
Connection to a USB Server/CPU
Connection to an External KVM Switch
Figure 7. RackView cable connectivity
Note: Cabling options include either a VGA/USB, or a DVI/USB cable.
Note: Please check cable details with your supplier.
Caution: The RackView KVM drawer is hot-pluggable, but components of connected devices, such as the
servers and KVM switch, may not be hot-pluggable. Plugging and unplugging cables while servers and KVM
switch are powered-on may cause irreversible damage to the servers, KVM and LCD console drawer. Before
attempting to connect anything to the RackView, we suggest turning off the power to all devices. Apply power
to connected devices only after the RackView has been powered-on. Rose Electronics is not responsible for
any product damage or warranty claims caused in this way.
RackView Sideways
DVI-D and
KB/MS
Console Cable
DVI-D
USB
USB Server
RackView Sideways
DVI-D and
KB/MS
Console Cable
USB
DVI-D
DVI-D + USB
KVM Switch

RackView Sideways (21" and 24") Manual 8
RackView Cables
There are 3 different combo connection cables available for RackView. The user should select one of these
cables at time of order placement. These cables are used to connect the RackView to either a PC or an
external KVM switch
Add either /K1, /K2 or /K3 onto the RackView part number
K1: VGA + USB K2: VGA + PS2
K3: DVI + USB
Figure 8. RackView device interface cables

OPERATION
RackView Sideways (21" and 24") Manual 9
RackView Operation
Power-On Procedure

Power on the RackView (see power switch on back panel)

Power on the KVM Switch or other connected product

Power on the CPU
Video Input Select Button

The RackView remembers the last valid video input selection, so if the CPU input has changed, the user
needs to re-select the video input.

Locate the “Video Input Select” button on the OSD display control panel

Push the Video Input Select button to toggle between VGA and DVI Input

Select the appropriate Video Input format (VGA or DVI)
OSD Selection
OSD Selection Panel
Figure 9. OSD menu selection

RackView Sideways (21" and 24") Manual 10
OSD Operation
OSD Configuration and Settings
Picture
Picture mode: Standard / Vivid / Soft / User mode to choose
Brightness: Adjust background black level of the screen image
Contrast: Adjust the difference between the image background
(black level) and the foreground (white level)
Hue: Adjust the screen hue value
Saturation: Adjust the saturation of the image color
Picture size: Adjust the image size
Color temp: Standard / Cool / Warm / User to choose
Noise reduce: Reduce the noise of the image
Sharpness: Adjust the image from weak to sharp
PC
Auto adjust: Automatically adjust sizes, centers and fine tunes
the video signal to eliminate waviness and distortion.
Clock: Adjust the clock value
Phase: Adjust the phase value
H. Position: Align the screen image left or right
V. Position: Align the screen image up or down
Audio
Audio mode: Movie / Voice / Normal / Music mode to choose
Volume: Adjust the volume of sound
Bass: Set the value of bass sound
Treble: Set the value of treble sound
Balance: Set the balance value of treble and bass sound
Analog TV audio: Set the value of analog TV audio sound
Mute: Turn off the surrounding sound
Misc.
Language: Select the language in which the OSD menu is
displayed - English
Sleep timer: Set the off time
PIP mode: Adjust picture in picture setting
PIP position: Enter into PIP position
PIP source: Enter into the Sub source and sound source
System reset: Return the adjustment back to factory setting
Information: Select for Help
Figure 10. RackView OSD configuration and settings

RackView Sideways (21" and 24") Manual 11
Picture in Picture and Picture by Picture Modes (PIP and PBP)
Note: Available on the RackView Sideways 24" model only.
PIP (Picture-In-Picture) and PBP (Picture-By-Picture) settings are available when two different video sources
are selected in the MISC option in the OSD.
PIP and PBP Settings
PIP Mode
Display the Sub screen in the Main screen.
OSD Menu →MISC →PIP Mode →Large / Small /
OFF
PIP Position
Adjust the position of the Sub screen (top left,
bottom left, top right, bottom right)
OSD Menu →MISC →PIP Position →top left / top
right / bottom left / bottom right
PIP Size
Adjust the size of the Sub screen (Large / Small)
OSD Menu →MISC →PIP Mode →Large / Small
PBP Mode
Display the Sub screen next to the Main screen.
OSD Menu →MISC →PIP Mode →PBP
Figure 11. PIP and PBP configuration

RackView Sideways (21" and 24") Manual 12
PIP and PBP Operation
PBP Size
Adjust the size of the Sub-screen (Large/Small)
OSD Menu --- MISC --- PBP Mode --- Large/Small
PIP / PBP Source
To select an input signal for PIP / PBP Sub screen.
OSD Menu →MISC
Figure 12. PIP and PBP settings and operation
Troubleshooting
If the RackView KVM Drawer fails to synchronize correctly with the attached product (PC, Switch, Extender),
and the monitor displays a distorted video pattern, press the screen power reset button once on the RackView
keyboard tray to re-synchronize the video signal

PRODUCT SAFETY
RackView Sideways (21" and 24") Manual 13
Safety
The RackView KVM Drawer, like all electronic equipment, should be used with care. To protect yourself from
possible injury and to minimize the risk of damage to the Unit, read and follow these safety instructions.

Follow all instructions and warnings marked on this Unit.

Except where explained in this manual, do not attempt to service this Unit yourself.

Do not use this Unit near water.

Assure that the placement of this Unit is on a stable surface.

Provide proper ventilation and air circulation.

Keep connection cables clear of obstructions that might cause damage to them.

Use only power cords, power adapter and connection cables designed for this Unit.

Keep objects that might damage this Unit and liquids that may spill, clear from this Unit. Liquids and
foreign objects might come in contact with voltage points that could create a risk of fire or electrical
shock.

Do not use liquid or aerosol cleaners to clean this Unit. Always unplug this Unit from the power source
before cleaning.
Remove power from the unit and refer servicing to a qualified service center if any of the
following conditions occur:

The connection cables are damaged or frayed.

The Unit has been exposed to any liquids.

The Unit does not operate normally when all operating instructions have been followed.

The Unit has been dropped or the case has been damaged.

The Unit exhibits a distinct change in performance, indicating a need for service.

SERVICE AND MAINTENANCE
RackView Sideways (21" and 24") Manual 14
Maintenance and Repair
This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance,
you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center.
This Return Authorization number must appear on the outside of the shipping container.
See Limited Warranty for more information.
When returning a Unit, it should be double-packed in the original container or equivalent, insured and shipped
to:
Rose Electronics
Attn: RA __________
10707 Stancliff Road
Houston, Texas 77099 USA
Technical Support
If you are experiencing problems, or need assistance installing your product, consult the appropriate section of
this manual. If, however, you require additional information or assistance, please contact the Rose Electronics
Technical Support Department at:
Phone: [phone]
E-mail: [email protected]
Web: www.rose.com
Technical Support hours are from: 8:00 am to 6:00 pm CST (USA), Monday through Friday.
Please report any malfunctions in the operation of this Unit or any discrepancies in this manual to the Rose
Electronics Technical Support Department.

APPENDICES
RackView Sideways (21" and 24") Manual 15
Appendix A —Specifications
Chassis Details RackView Sideways 21-inch RackView Sideways 24-inch
Display Monitor and Size 21.5" HD, 1U height 24.1" Ultra-HD, 1U height
Drawer Dimensions 17.4 x 26.4 x 1.73 inch
(441.6 x 670 x 44 mm)
17.4 x 27.6 x 1.73 inch
(441.6 x 700 x 44 mm)
Weight 32.3 lb (14.7Kg) 33.7 lb (15.3Kg)
Mounting Rail Depth (Distance) 24.8 – 33.9-inch (630-860mm) 26 – 35-inch (660-890mm)
Video Specification RackView Sideways 21-inch RackView Sideways 24-inch
Maximum Resolution 1920 x 1080 @60Hz 1920 x 1200 @60Hz
Brightness and Backlight Type 250 cd/m², LED 300 cd/m², LED
Color Support 16.7M 16.7M
Contrast Ratio (typical.) 1000:1 1000:1
Viewing Angle (H/V) 85/85/80/80 (L/R/U/D) 89/89/89/89
Dot Pitch 0.248mm 0.27mm
Display Area 476.64 H x 268.11 V mm 518.40 H x 324.0 V mm
Response Time 5ms 14ms
Surface Treatment Haze 25%, hard coating Anti-glare, hard coating
Surface Hardness 3H 3H
DVI Signal DVI-D, TMDS single-link DVI-D, TMDS single-link
HDMI Signal HDMI 1.3, CEA-861-D HDMI 1.3, CEA-861-D
VGA Signal Analog 0.7Vp-p Analog 0.7Vp-p
Plug & Play DDC (DVI and VGA) VESA EDID 1.3 VESA EDID 1.3
Connectors and Controls
Console Ports (standard model)
(one cable included)
1 x DVI-D
1 x KVM (for VGA video, keyboard and mouse signals)
Power 1 x IEC power connector
Display power switch 1 x Display power-off switch on the front panel
USB2.0 1 x USB2.0 port on the front panel with the USB-Hub switch option
Power
Power Input Auto-sensing 100 to 240VAC, 50 / 60Hz
Power Consumption RackView 21”: Screen ON = 32W or less, Power Saving Mode = 4W or less
RackView 24”: Screen ON = 40W or less, Power Saving Mode = 5W or less
Environmental, Approvals and Support
Operating Temp 0˚ to 55˚C Degree
Storage Temp -20˚ to 60 ˚C Degree
Operating Humidity Operating: 20~90%, non-condensing
Shock 10G acceleration (11ms duration)
Vibration 5~500Hz 1G RMS random vibration
Regulation/Approvals cUL, FCC, CE, RoHS2, REACH
Compatibility Multi-platform - Mix PCs, SUNs, IBMs, HPs and DELLs.
LCD Panel MTBF 30,000 hours