ROSIERES RHP90TX User manual

RHP90TX
Cooker Hood
Instruction Manual
ENGLISH(EN)--------------------------------------------------------------------------------page 001
FRENCH(FR) --------------------------------------------------------------------------------page 014

1


RHP90TX
Hood
InstructionManual









2
Content
1…………………………………..………………………………Safety instructions
2…………………………………..………………………………Installation
3…………………………………..………………………………Start using your cooker hood
4…………………………………..………………………………Troubleshooting
5…………………………………..………………………………Maintenance and cleaning
6…………………………………..………………………………Environment protection

3
SAFETYINSTRUCTIONS
This manual explains the proper installation and use of your cooker hood, please read
it carefully before using even if you are familiar with the product. The manual should
be kept in a safe place for future reference.
Never to do:
● D o not try to use the cooker hood without
the grease filters or if the filters are
excessively greasy!
●Do not install above a cooker with a high
level grill.
●Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
●Never leave naked flames under the
cooker hood.
●If the cooker hood is damaged, do not
attempt to use.
●Do not flambé under the cooker hood.
●CAUTION: Accessible parts may become
hot when used with cooking appliances.
●The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest part of
the cooker hood. (When the cooker hood
is located above a gas appliance, this
distance shall be at least 65 cm)
●The air must not be discharged into a flue
that is used for exhausting fumes from
appliances burning gas or other fuels.
Always to do:
● Important! Always switch off the
electricity supply at the mains during
installation and maintenance such as light
bulb replacement.
●The cooker hood must be installed in
accordance with the installation
instructions and all measurements
followed.
●All installation work must be carried out
by a competent person or qualified
electrician.
●Please dispose of the packing material
carefully. Children are vulnerable to it.
● P ay attention to the sharp edges inside
the cooker hood especially during
installation and cleaning.
●Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker hood.
●Warning: Failure to install the screws or
fixing device in accordance with these
instructions may result in electrical
hazards.
●Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.

4
Always to do:
●Always put lids on pots and pans when
cooking on a gas cooker.
●When in extraction mode, air in the room
is being removed by the cooker hood.
Please make sure that proper ventilation
measures are being observed. The
cooker hood removes odours from room
but not steam.
●Cooker hood is for domestic use only.
●If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
●This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
Always to do:
● Caution: The appliance and its
accessible parts can become hot during
operation. Be careful to avoid touching
the heating elements. Children younger
than 8 years old should stay away unless
they are under permanent supervision.
● There shall be adequate ventilation of
the room when the cooker hood is used
at the same time as appliances burning
gas or other fuels.
●There is a fire risk if cleaning is not
carried out in accordance with the
instructions
●Regulations concerning the discharge of
air have to be fulfilled.
●Clean your appliance periodically by
following the method given in the chapter
MAINTENANCE.
●For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this
instruction manual.
●Regarding the details about the method
and frequency of cleaning, please refer to
maintenance and cleaning section in the
instruction manual.
●Cleaning and user maintenance shall not
be made by children without supervision.
●When the cooker hood and appliances
supplied with energy other than electricity
are simultaneously in operation, the
negative pressure in the room must not
exceed 4 Pa (4 x 10-5 bar).
●WARNING: Danger of fire: do not store
items on the cooking surfaces.
●A steam cleaner is not to be used.
●NEVER try to extinguish a fire with water,
but switch off the appliance and then
cover flame e.g. with a lid or a fir e blanket.

5
Please kindly be notedT-shaped plastic outlet and v-flaps can not be used at the same
time. You can use them in two ways :
1) Add v-flap on existing outlet;
2) Use T-shaped plastic outlet, no add v-flap.
INSTALLATION(VENTOUTSIDE)
MOUNTINGOFTHEV-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the half-parts
to its body.The images only show an example of how to mount the V-flap,the outlet may be
various according to different models and configuration.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6;
• a pin 3 should be top oriented;
• the axis 4 should be inserted in the holes 5 on body;
• repeat all the operations for the 2nd half-part.
Note: The product is provided with v-flap accessory. This accessory is not mandatory for
installation, operation and use of the product.


If you have an outlet to the outside, your cooker hood can be connected as below picture
by means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material
with an interior diameter of 150mm)
1. Before installation, turn the unit off and unplug it from the outlet.

6
2. The cooker hood should be placed at a distance of 65~75cm above the cooking
surface for best effect.
3. Install the hook on a suitable place once the installation height is fixed, and keep it in
line. The fixed position of the inside chimney bracket is the place of highest chimney.
See pic 2.
4. Install the v-flap,converter and expansion pipe on the cooker hood. Put the cooker
hood on to the hook. See pic 3 & pic 4.
5. Fix the outside chimney bracket on the outside chimney with 2 ST4*8mm screws, and
be sure that the inside chimney can be adjusted the height in it freely. Meanwhile lead
the expansion pipe to outdoor.See Pic 5 & Pic 6.

7
6. Adjust the height of the inside chimney to the position of the inside chimney bracket
and fix on it by screws, after adjusting the position, fix the body with safety screws.
Note: The two safety vents are positioned on the back housing, with diameter of
6mm.See pic 6 & 7.


InstallationofT-shapedplasticoutlet(optional)
1. As shown in pic 1,install the mounting bracket on the T-shaped plastic outlet with 4pcs
ST3*12mm screws.Then place the adjusted pipe to both sides of the outlet. Adjust to
the required distance of adjustment pipe,make sure the left and right sides are
symmetrical,and fix it well with 2 pcs ST3*12mm screws.
2. See pic 2,2 pcs ST4*8mm screws will be used to fix the T-shaped plastic outlet to the
inside chimney bracket.
3. See pic 3,fix the inside chimney bracket and T-shaped plastic outlet on the wall with
ST4*30mm screws and wall plugs.
4. See pic 4 & pic 5,use 2 pcs ST4*8mm screws to fix the inside chimney to the inside
chimney bracket.

8
HINTSFOREXHAUSTDUCTINSTALLATION
The following rules must be strictly followed to obtain optimal air extraction:
• Keep expansion pipe short and straight.
• Do not reduce the size or restrict expansion pipe.
• When using expansion pipe always install the pipe pulled taut to minimize pressure loss.
• Failure to observe these basic instructions will reduce the performance and increase
noise levels of the cooker hood.
• Any installation work must be carried out by a qualified electrician or competent person.
•Do not connect the ducting system of the hood to any existing ventilation system which is
being used for any other appliance ,such as warmer tube, gas tube , hot wind tube.
•The angle of the bend of the expansion pipe should not be less than 120º; you must direct
the pipe horizontally, or, alternatively, the pipe should go up from the initial point and
should be led to an outer wall.
•After the installation ,make sure that the cooker hood is level to avoid grease collection at
on end.
•Ensure the expansion pipe selected for installation complies with relevant standards and
is fire retardant.
WARNING: For safety reason, please use only the same
size of fixing or mounting screw which are
recommended in this instruction manual.
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.

StartUsingYourCookerHood
LED touch control

1.Press the “Power” button, the button control the “on” & “off ” of the hood.
2.Press the “Speed” button time after time, the motor runs as low / mid / high / low / mid…,
the speed runs circularly; and the LED display will indicate as 1-2-3-1-2… circularly.

Timer Lamp Speed Power

9
3.Press “Lamp” button, the light is on, press this button again, the light is off.Please note
the Lamp is not under control of the on/off button.
4.When the hood is working, if press the “Timer” button, the hood will go into the status of
acquiescent working (acquiescent time is 9mins), and then, LED display will be shown
9.8.7.6 ...decreasing by 1,when time is up, the hood will be off automatically and the lamp
will extinguish. If pressing “Timer” button, the hood will go in or go out “Timer” function.
TROUBLESHOOTING
Fault PossibleCause Solution
Light on, but motor
does not work
Fan switch turned off Select a fan switch position.
Fan switch failed Contact service center.
Motor failed Contact service center.
Light does not
work, motor does
not work
House fuses blown Reset/Replace fuses.
Power cord loose or
disconnected
Refit cord to power outlet.
Switch power outlet on.
Oil leakage
One way valve and the outlet
are not tightly sealed
Take down the one way valve
and seal with sealant.
Leakage from the connection of
chimney and cover Take chimney down and seal.
Lights not working Broken/Faulty globes Replace globes as per this
instruction.
Insufficient suction
The distance between the
cooker hood and the gas top is
too far
Refit the cooker hood to the
correct distance.
The Cooker hood
inclines
The fixing screw not tight
enough
Tighten the hanging screw and
make it horizontal.
NOTE:
Any electrical repairs to this appliance must conform to your local, state and federal
laws.Please contact the service centre if in any doubt before undertaking any of the
above.Always disconnect the unit from the power source when opening the unit.
CUSTOMERASSISTANCESERVICE
If you cannot identify the cause of he operating anomaly;switch off the appliance (do not
subject it to rought treatment.) and contact the Assistance Service.
PRODUCT SERIAL NUMBER.Where can I find it?
It is important that you to inform the Assistance Service of your product code and its serial
number(a 16 character code which begins with the number 3);this can be found on the
guarantee certificate or on the data plate located on the appliance.
It will help to avoid wasted journerys to technicaians,thereby (and most significantly)
saving the corresponding callout charges.