Roto-Mix 354-12 Guide

441904 06/2021 Printed in U.S.A.
354-12, 354-12B
FEED MIXER
OPERATION AND PARTS MANUAL
ROTO-MIX
P.O. BOX 1724
2205 E. Wyatt Earp Blvd.
Dodge City, Kansas 67801
[phone]
© ROTO-MIX 2006
SERIAL NUMBER ____________

2
TABLE OF CONTENTS
PAGE #
WARRANTY.............................................................................................................................................3
SCALES WARRANTY & SERVICE POLICY...........................................................................................4
OPERATOR QUALIFICATIONS..............................................................................................................5
SAFETY INFORMATION........................................................................................................................6-8
OPERATION..........................................................................................................................................6-20
LUBRICATION CHART...........................................................................................................................24
354-12 SPECIFICATIONS......................................................................................................................25
PTO CHART ...........................................................................................................................................26
354-12 STATIONARY DIMENSIONS.....................................................................................................27
354-12 TRAILER DIMENSIONS.............................................................................................................28
354-12 TRAILER DIMENSIONS (W / CONVEYOR)...............................................................................29
354-12 TRUCK DIMENSIONS................................................................................................................30
354-12 MOUNTING DIMENSIONS.........................................................................................................31
TRUCK HYDRAULIC SHCEMATIC........................................................................................................32
JOYSTICK ASSEMBLY.......................................................................................................................... 33
WIRING SCHEMATIC FOR DISCHARGE DOOR.................................................................................. 34
SPOUT RUBBER.................................................................................................................................... 35
17” SPOUT ASSEMBLY .........................................................................................................................36
SPOUT MAGNET ASSEMBLY............................................................................................................... 37
CHAIN CONVEYOR ASSEMBLY.........................................................................................................38-39
CONVEYOR HYDRAULIC ASSEMBLY (SINGLE CYLINDER).............................................................. 40
STAGGERED ROTOR ASSEMBLY.......................................................................................................41
3-ARM ROTOR ASSEMBLY (BEFORE SERIAL #890473440)..............................................................42
3-ARM ROTOR ASSEMBLY (FROM SERIAL #890473440).................................................................. 43
5-ARM ROTOR ASSEMBLY (BEFORE SERIAL #890473440)..............................................................44
5-ARM ROTOR ASSEMBLY (FROM SERIAL #890473440).................................................................. 45
12” STANDARD AUGER ASSEMBLY (BEFORE SERIAL #890473440) ............................................... 46
12” STANDARD AUGER ASSEMBLY (FROM SERIAL #890473440) ................................................... 47
12” OPTIONAL AUGER ASSEMBLY...................................................................................................... 48
SCALE INDICATOR ASSEMBLY...........................................................................................................49
OIL BATH DOOR ASSEMBLY................................................................................................................50
DISCHARGE DOOR ASSEMBLY........................................................................................................... 51
HANDWHEEL ASSEMBLY..................................................................................................................... 52
354 AUGER FLOAT ASSEMBLY ........................................................................................................... 53
354 FRONT END ASSEMBLY (BEFORE SERIAL #890473440)...........................................................54
354 FRONT END ASSEMBLY (FROM SERIAL #890473440)............................................................... 55
354 TRUCK & STATIONARY LOADCELL FRAME................................................................................ 56
354 TRUCK & STATIONARY WEIGH BAR FRAME .............................................................................. 57
TRAILER WEIGH BAR ...........................................................................................................................58
354-12 TRAILER ASSEMBLY ................................................................................................................59
10-BOLT HUB & SPINDLE ASSEMBLY................................................................................................. 60
TRAILER DRIVELINE.............................................................................................................................61
TRUCK DRIVELINE ASSEMBLY (STANDARD TRANSMISSION)........................................................ 62
TRUCK DRIVELINE ASSEMBLY (AUTOMATIC TRANSMISSION)....................................................... 63
200 SER. HUB CITY 2:1 GEARBOX ASSEMBLY..................................................................................64
LUBRICATION ASSEMBLY....................................................................................................................65
STATIONARY DRIVE ASSEMBLY (SINGLE MOTOR)........................................................................66-67
STATIONARY DRIVE ASSEMBLY (DUAL MOTOR) ...........................................................................68-69
354 DRIVE ASSEMBLY (BEFORE SERIAL #890473440)...................................................................70-71
354 DRIVE ASSEMBLY (FROM SERIAL #890473440).......................................................................72-73
354 TRAILER DRIVESHAFT.................................................................................................................. 74
354 TRUCK DRIVESHAFT REAR, AUTOMATIC TRANSMISSION.......................................................75
354-12 TRUCK DRIVELINE (FRONT & REAR) .....................................................................................76
ROTO-HAY PROCESSOR ASSEMBLY.................................................................................................77
ROTO-HAY PROCESSOR (CABLE OPTION)....................................................................................... 78
ROTO-HAY PROCESSOR (HYDRAULIC OPTION) .............................................................................. 79
FENDERS & MUD FLAPS......................................................................................................................80
LADDER ASSEMBLY.............................................................................................................................81

3
ROTO-MIX LLC warrants to the original purchaser all products manufactured by it to be free from defects in
material and workmanship under normal use and service.
ROTO-MIX’s obligation under this warranty is limited to repairing or replacing, as the company may elect,
free of charge and without charge for installation, at the place of business of a dealer or distributor author-
ized to handle the equipment covered by this warranty or at a ROTO-MIX facility, any parts that prove, in the
company’s judgment, to be defective in material or workmanship within one (1) year after delivery to the
original purchaser, and still owned by the original purchaser. This warranty shall in no way make ROTO-MIX
liable to anyone for personal injuries or damages, loss of time, or expense of any kind either direct or indi-
rect resulting from part failure or defect. This warranty is subject to acts of God, fire and existing conditions
of supply and demand, or production, or ability or inability to deliver, or for any other valid reason beyond
the reasonable control of ROTO-MIX, to obtain materials, manufactured replacement parts, or make delivery
thereof. No distributor, dealer, agent, or ROTO-MIX employee (other than the CEO or President in writing) is
authorized to extend any other or further express or implied warranty or incur any additional obligation on
ROTO-MIX’s behalf in connection with the sale of this product.
If ROTO─MIX, or its duly authorized representative, shall find that such returned part or parts are defective
and such defects, or defect, are included in and covered by said warranty, then such defective part or parts
shall promptly be replaced without charge to the purchaser, F.O.B. the ROTO─MIX plant.
Product Registration - It is a condition of this warranty that the original purchaser must fill out the warranty
card furnished by ROTO-MIX and that it be returned to ROTO-MIX within 10 days of purchase and be re-
corded in ROTO-MIX’s owner file for this warranty to be valid. In the event an owner’s card is not on file at
the ROTO-MIX office, the warranty period will extend only from date equipment was picked up or shipped
from the ROTO-MIX plant.
Maintenance - It is the customer’s responsibility to maintain their equipment in accordance with the instruc-
tions provided in the Operator’s Manual. ROTO-MIX recommends that you keep records and receipts; you
may be asked to prove that maintenance instructions have been followed.
Operation –It is the customer’s responsibility to operate the equipment only for the purpose for which it
was designed and in accordance with all safety and operational recommendations contained in the Opera-
tors Manual. If a defect in materials or workmanship occurs, it is the customer’s responsibility to cease oper-
ating the equipment until authorized repairs are made. Damage, which occurs from continued operation,
may not be covered by this warranty.
What this Warranty Covers
This warranty covers failures caused by defects in materials or workmanship only.
This Warranty does not cover failures caused by:
-Improper operation
-Natural calamities
-Unauthorized modifications
-Unauthorized repairs
-Use of Non ROTO-MIX parts
-Neglected maintenance
-The use of PTO Shaft
Adaptors
-Usage contrary to the
intended purpose of the
product
Warranty continues on the next page.

4
SCALES WARRANTY & SERVICE POLICY
DIGI-STAR SCALE SYSTEMS
Digi-Star, LLC warrants for a period of one year from date of installation, to correct by repair or replacement,
at Digi-Star’s option, any defect in material or workmanship in any part of this product. In the event of
replacement, Digi-Star’s sole obligation shall be to provide replacement products or parts. F.O.B. Digi-Star,
LLC, W5527 Hwy 106, Fort Atkinson, WI 53538 USA.
WEIGH-TRONIX SCALE SYSTEMS
WEIGH-TRONIX warrants for a period of one year from date of installation, to correct by repair or
replacement, at Weigh-Tronix’s option, any defect in material or workmanship in any part of this product. In
the event of replacement, Weigh-Tronix’s sole obligation shall be to provide replacement products or parts.
F.O.B. Avery Weigh-Tronix, 1000 Armstrong Drive, Fairmont, MN 56031-1439 USA.
Limited Warranty Statement continued
This Warranty does not cover replacement of Wear or Maintenance Items including, but not limited to.
This Warranty does not cover:
-Pickup and delivery of the equipment
-Service Calls or Travel Time to and from sites
-Rental of replacement equipment during repair period
-Products that have been declared a total loss and subsequently salvaged
-Overtime labor charges
-ROTO-MIX is not responsible and will not be liable for damage caused to persons or property, commercial
loss, loss of time or production, loss of use by reason of the installation or use of ROTO-MIX products or
their mechanical failure.
Right to Make Changes
ROTO-MIX reserves the right to make any changes to a ROTO-MIX product at any time without incurring any
obligation with respect to any product previously ordered, sold or shipped, with or without notice.
Parts Warranty
ROTO-MIX warranties replacement parts against defects in materials or workmanship for a period of 90
days or the remainder of the product warranty, whichever is longer. Remedy for defective replacement
parts for units that are beyond the original product warranty, will be limited to replacement of the failed
part. Failures that are due to damage, improper installation, lack of maintenance or improper operation will
not be covered.
ROTO-MIX 2205 East Wyatt Earp Blvd., Dodge City, KS 67801 [phone] Fax: [phone]
-Lubricants
-Filters
-Hoses
-Tires
-Augers
-Wipers
-Chains
-Idlers
-Batteries
-Blades
-Belts

5
Operation Of this mixer/feeder shall be limited to competent and experienced persons. In addition,
anyone who will operate or work around a mixer/feeder must use good common sense. In order to be
qualified, he or she must also know and meet all other qualifications, such as:
1. Some regulations specify that no one under the age of sixteen (16) may operate power machinery.
It is your responsibility to know what these regulations are in your area and/or situation.
2. Current OSHA regulations state in part: At the time of initial assignment and at least annually
thereafter, the employer shall instruct EVERY employee in the safe operation and servicing of all
equipment with which the employee is, or will be involved.
3. Unqualified persons are to
STAY OUT OF THE WORK AREA.
4. A person who has not read and understood all operating and safety instructions is not qualified to
operate the machinery.
FAILURE TO READ THIS MIXER/FEEDER MANUAL AND ITS SAFETY
INSTRUCTIONS IS A MISUSE OF THE EQUIPMENT.
OPERATOR QUALIFICATIONS

6
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED
TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND
THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN
INJURY OR DEATH.
SAFETY
THIS SYMBOL MEANS
-ATTENTION!
-BECOME ALERT!
-YOUR SAFETY IS INVOLVED!
SIGNAL WORDS: Note the use of the signal words DANGER, WARNING, and CAUTION with the
safety messages. The appropriate signal word for each has been selected using the following guidelines:
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in serious
injury or death. This signal word is to be limited to the most extreme situations typically for machine
components which, for functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided, will result in serious
injury or death, and includes hazards that are exposed when guards are removed. It may also be used
to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
If you have questions not answered in this manual or require additional copies or the manual is damaged,
please contact your dealer or ROTO-MIX, 2205 E. Wyatt Earp, Dodge City, Kansas, 67801. (Telephone)
620-225-1142 (Fax) 620-225-6370

7
REMEMBER: The careful operator is the best operator. Most accidents are caused by human error.
Certain precautions must be observed to prevent the possibility of injury or death.
SAFETY FIRST
DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR
NEAR THE MACHINE.
NEVER START MACHINE UNTIL ALL GUARDS AND SAFETY SHIELDS ARE IN
PLACE.
DO NOT CLEAN, ADJUST OR LUBRICATE THE MACHINE WHILE IT IS IN
MOTION.
BEFORE STARTING TRACTOR ENGINE, BE SURE PTO SHIELDS TURN FREELY.
LOOSE OR FLOPPY CLOTHING SHOULD NOT BE WORN BY THE OPERATOR.
OPERATING PRECAUTIONS & INSTRUCTIONS:
A. Check to see that no obstructions are present in the mixer prior to start up.
B. Before loading, run the mixer empty and check all operations.
C. Do not overload the mixer, as the mixing efficiency may be reduced and unit damage may
occur. (See loading instructions).
D. Remove all moisture drain plugs if the mixer is going to set in the rain or snow.
E. Be sure all shields are in place before operation.
F. Use common sense when operating.

8
EQUIPMENT SAFETY GUIDELINES
Safety of the operator is one of the main concerns in designing and developing a new piece of
equipment. Designers and manufactures build in as many safety features as possible. However,
every year many accidents occur which could have been avoided by a few seconds of thought and
a more careful approach to handling equipment. You, the operator, can avoid many accidents by
observing the following precautions in this section. To avoid personal injury, study the following
precautions and insist those working with you, or for you, follow them.
In order to provide a better view, certain photographs or illustrations in this manual may show an
assembly with a safety shield removed. However, equipment should never be operated in this
condition. Keep all shields in place. If shield removal becomes necessary for repairs, replace the
shield prior to use.
Replace any CAUTION, WARNING, DANGER or instruction safety decal that is not readable or
is missing. Location of such decals are indicated in this manual.
Do not attempt to operate this equipment under the influence of drugs or alcohol.
Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The operator
should be a responsible adult familiar with farm machinery and trained in this equipment’s operations.
Do not allow persons to operate or assemble this unit until they have read this manual and have
developed a thorough understanding of the safety precautions and of how it works.
To prevent injury or death, use a tractor equipped with a Roll Over Protective System (ROPS). Do
not paint over, remove or deface any safety signs or warning decals on your equipment. Observe all
safety signs and practice the instructions on them.
Never exceed the limits of a piece of machinery. in its ability to do a job, or to do so safely, is in
question - DON’T TRY IT.
LIGHTING AND MARKING
It is the responsibility of the customer to know the lighting and marking requirements of the local
highway authorities and to install and maintain the equipment to provide compliance with the
regulations. Add extra lights when transporting at night or during periods of limited visibility.

KEEP ALL SHIELDS IN PLACE
Do not operate mixer/feeder without safety shields in place.
Rotating parts can crush or dism ember causing personal injury or
death.
Disconnect PTO driveline before removing shields for adjustment
or service.
OPERATE MIXER/FEEDER SAFELY
Rotating parts can ent angle or stri ke people, resulting in personal
injury or death.
Never enter a mixer/feeder while in operation.
Operate the mixer/feeder from the operator’s seat only.
Do not exceed load capacit y of the mixer/feeder. (Se e loading
instructions).
Reduce speed when turning or traveling on rough terrain.
KEEP RIDERS OFF MIXER/FEEDER
Keep riders off.
Riders are subject to injury such as being struck by foreign
objects and being thrown off. Riders also obstruct the
operator’s view resulting in the machine being operated in
an unsafe manner.
9

10
STAY CLEAR OF ROTATING DRIVELINES
Entanglement in rotating driveline can cause serious injury or death.
Keep tractor m aster shield and dr iveline shields in place at all
times. Make sure rotating shields turn freely.
Wear close f itting clothing. St op the engine and be sure PT O
driveline is stopped bef ore making adjustments, connections, or
cleaning out PTO driven equipment .
PREVENT BATTERY EXPLOSIONS
Keep sparks, lighted matches, and open flame away from the top of
battery. Battery gas can explode.
Never check batter y charge b y placing a metal object across the
posts. Use a volt-meter or hydrometer.
Do not charge a frozen battery; it may explode. Warm battery to
16C (60F)
AVOID HIGH-PRESSURE FLUIDS
Escaping fluid under pressure can penetrate t he skin causing seriou s
injury or death.
Avoid the hazard relieving pressure before disconnecting hydraulic
or other lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and body
from high pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid injected
into the skin must be surgically removed within a few hours or
gangrene may result. Doctors unfamiliar with this type of injury
should reference a knowledgeable medical source.

PREPARING TRACTOR FOR TRAILER MIXER
POSITIONING DRAWBAR
IMPORTANT: Drive components can be damaged from
excessive speed. Under no circumstances
should a feed mixer equipped with 540 RPM be
operated by a tractor with 1000 RPM PTO.
Feed mixers are available with either 540 or 1000 RPM
driveline. Match tractor PTO with the feed mixer driveline.
IMPORTANT: To prevent driveline damage, adjust tractor
drawbar to recommended setting. Disengage tractor
PTO before turning.
Remove clevis if equipped. Turn offset drawbar down.
Adjust drawbar length:
PTO SPEED DIMENSION (A)
540 RPM 14 inches (356 mm)
1000 RPM 16 inches (406)
ADJUST TRAILER HITCH CLEVIS
Mixer should be approximately level when attached to tractor.
Adjust clevis by changing hole location on tongue.
Hitch Pin Size — 1” x 7”
11

12
SAFETY SIGNS
(A) #440827
(B) #4408321
(C) #440819
(D) #440818
(E) #440826
(B)
(A)
(C)
(D)
(E) (E)
(D)
(A)
(B)

13
SAFETY SIGNS
(A) #440828
(C) #440826
(B) #440831
(A)
(B)
(B) (A)
(C) (C)

14

15
SAFETY DECAL CARE
Keep safety decals and signs clean and legible at all times.
Replace safety decals and signs that are missing or have become illegible.
Replaced parts that displayed a safety sign should also display the current sign.
Safety decals or signs are available from your dealer or the ROTO-MIX manufacturing plant.
How to Install Safety Decals:
Be sure that the installation area is clean and dry.
Decide on the exact position before you remove the backing paper.
Remove the smallest portion of the split backing paper.
Align the decal over the specified area and carefully press the small portion with the exposed sticky
backing in place.
Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in
place.
Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing
paper.

16
REMEMBER
Your best assurance against accidents is a careful and responsible operator. If there is
any portion of this manual or function you do not understand, contact your dealer or the
ROTO-MIX plant.
BEFORE OPERATION:
Carefully study and understand this manual.
Do not wear loose-fitting clothing which may catch in moving parts.
Always wear protective clothing and substantial shoes.
Keep wheel lug nuts or bolts tightened to specified torque.
Assure that agricultural implement tires are inflated evenly.
Give the unit a visual inspection for any loose bolts, worn parts or cracked welds, and make
necessary repairs. Follow the maintenance safety instructions included in this manual.
Be sure that there are no tools lying on or in the mixer/feeder.
Do not use the unit until you are sure that the area is clear, especially children and animals.
Because it is possible that this mixer/feeder may be used in dry areas or the presence of
combustibles, special precautions should be taken to prevent fires and fire fighting equipment
should be readily available.
Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar with
your new mixer/feeder.
Practice operation of your mixer/feeder and its attachments. Completely familiarize yourself and
other operators with its operation before using.
Securely attach to towing unit. Use a high strength, appropriately sized hitch pin with a mechanical
retainer.
Do not allow anyone to stand between the tongue or hitch and the towing vehicle when backing up
to the mixer/feeder.

17
DURING OPERATION:
Beware of bystanders, particularly children! Always look around to make sure that it is safe to
start the engine of the towing vehicle or move the unit. This is particularly important with higher
noise levels and quiet cabs, as you may not hear people shouting.
NO PASSENGERS ALLOWED - Do not carry passengers anywhere on, or in, the tractor or
equipment, except as required for operation.
Keep hands and clothing clear of moving parts.
Do not clean, lubricate or adjust your mixer/feeder while it is moving.
Be especially observant of the operating area and terrain - watch for holes, rocks or other hidden
hazards. Always inspect the area prior to operation.
Do not operate near the edge of drop-offs or banks.
Do not operate on steep slopes as overturn may result.
Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.
Pick the levelest possible route when transporting across fields. Avoid the edges of ditches or
gullies and steep hillsides.
Be extra careful when working on inclines.
Periodically clear the equipment of brush, twigs or other materials to prevent buildup of dry
combustible materials.
Maneuver the tractor or towing vehicle at safe speeds.
Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury
or death.
Avoid loose fill, rocks and holes; they can be dangerous for equipment operation or movement.
Allow for unit length when making turns.
Do not walk or work under raised components or attachments unless securely positioned and
blocked.
Keep all bystanders, pets and livestock clear of the work area.
Operate the towing vehicle from the operator’s seat only.
Never stand alongside of the unit with engine running. Never attempt to start engine and/or operate
machine while standing alongside of unit.

18
DURING OPERATION (CONT.)
Never leave running mixer/feeder unattended.
As a precaution, always recheck the hardware on mixer/feeder following every 100 hours of
operation. Correct all problems. Follow the maintenance safety procedures.
FOLLOWING OPERATION:
Following operation, or when unhitching, stop the tractor or towing vehicle, set the brakes, disengage
the PTO and all power drives, shut off the engine and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of time. Damage
and livestock injury could result.
Do not permit children to play on or around the stored unit.
Make sure parked machine is on a hard, level surface and engage all safety devices.
Wheel chocks may be needed to prevent unit from rolling.
HIGHWAY AND TRANSPORT OPERATIONS:
Adopt safe driving practices:
Keep the brake pedals latched together at all times. Never use independent braking with
machine in tow as loss of control and/or upset of unit can result.
Always drive at a safe speed relative to local conditions and ensure that your speed is low
enough for an emergency stop to be safe and secure. Deep speed to a minimum.
Reduce speed prior to turns to avoid the risk of overturning.
Avoid sudden uphill turns on steep slopes.
Always keep the tractor or towing vehicle in gear to provide engine braking when going downhill.
Do not coast.
Do not drink and drive.

19
HIGHWAY AND TRANSPORT OPERATIONS (CONT.):
Comply with state and local laws governing highway safety and movement of farm machinery on
public roads.
Use approved accessory lighting flags and necessary warning devices to protect operators of
other vehicles on the highway during daylight and nighttime transport.
The use of flashing amber lights is acceptable in most localities. However, some localities prohibit
their use. Local laws should be checked for all highway lighting and marking requirements.
When driving the tractor and mixer/feeder on the road or highway under 20 MPH (40 KPH) at
night or during the day, use flashing amber warning lights and a slow moving vehicle (SMV)
identification emblem.
Plan your route to avoid heavy traffic.
Be a safe courteous driver. Always yield to oncoming traffic in all situations, including narrow
bridges, intersections, etc.
Be observant of bridge loading ratings. Do not cross bridges rated lower than he gross weight at
which you are operating.
Watch for obstructions overhead and to the side while transporting.
Always operate mixer/feeder in a position to provide maximum visibility at all times. Make
allowances for increased length and weight of the mixer/feeder when making turns, stopping the
unit, etc.
PERFORMING MAINTENANCE:
Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed
building. The exhaust fumes may cause asphyxiation.
Before working on the mixer/feeder, stop the towing vehicle, set the brakes, disengage the PTO
and all power drives, shut off the engine and remove the ignition keys.
Be certain all moving parts on attachments have come to a complete stop before attempting to
perform maintenance.
Always use a safety support and block the wheels. Never use a jack to support the machine.

20
PERFORMING MAINTENANCE (CONT.):
Always use the proper tools or equipment for the job at hand.
Use extreme caution when making adjustments.
Never use our hands to locate hydraulic leaks on attachments. Use a small piece of cardboard or
wood. Hydraulic fluid escaping under pressure can penetrate the skin.
When disconnecting hydraulic lines, shut off hydraulic supply and relieve all hydraulic pressure.
Openings in the skin and minor cuts are susceptible to infection from hydraulic fluid. If injured by
escaping hydraulic fluid, see a doctor at once. Gangrene can result. Without immediate treatment,
serious infection and reactions can occur.
Replace all shields and guards after servicing and before moving.
After servicing, be sure all tools, parts and service equipment are removed.
Do not allow grease or oil to build up on any step or platform.
Never replace hex bolts with less than grade five (5) bolts unless otherwise specified.
Where replacement parts are necessary for periodic maintenance and servicing, genuine factory
replacement parts must be used to restore your equipment to original specifications. ROTO-MIX
will not claim responsibility for use of unapproved parts and/or accessories and other damages as
a result of their use.
If equipment has been altered in any way from original design, ROTO-MIX does not accept any
liability for injury or warranty.
A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance
on this mixer/feeder.