Rotronic HygroLab C1 User manual

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
1
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
HygroLab C1 Bench-Top Indicator
User Guide
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
2
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Table of contents
1 Overview......................................................................................................................................................3
2 General description....................................................................................................................................4
2.1 Configuration software ............................................................................................................................. 4
2.2 Power supply............................................................................................................................................ 4
2.3 Probe inputs ............................................................................................................................................. 4
2.4 Measured parameters .............................................................................................................................. 4
2.5 Calculated parameters ............................................................................................................................. 4
2.6 Alarm Indication on the display ................................................................................................................ 5
2.7 Real time clock......................................................................................................................................... 5
2.8 Back panel and digital interface ............................................................................................................... 5
3 Basic operation...........................................................................................................................................6
3.1 Display ..................................................................................................................................................... 6
3.2 Keypad ..................................................................................................................................................... 7
3.3 ON/OFF key ............................................................................................................................................. 7
3.4 Internal menu ...........................................................................................................................................8
3.5 Frequently used settings ........................................................................................................................ 11
3.5.1 Unit system ............................................................................................................................ 11
3.5.2 Date and time......................................................................................................................... 11
3.5.3 Select the calculated parameter for a probe input .................................................................. 11
3.5.4 Select which probe and/or parameters are shown on the display .......................................... 11
3.6 Connecting the HygroLab C1 to a PC .................................................................................................... 11
3.7 Practical advice for measuring humidity ................................................................................................. 12
4 Aw Measurement ......................................................................................................................................12
4.1 Enabling Aw Measurement .................................................................................................................... 12
4.2 Water activity measurement settings:..................................................................................................... 13
4.3 Aw probe usage guidelines .................................................................................................................... 13
4.4 Using the AwQuick mode ....................................................................................................................... 14
4.5 Using the AwE mode.............................................................................................................................. 17
4.6 Viewing the captured data (automatic data capture enabled) ................................................................ 19
5 User configurable settings and functions ..............................................................................................20
5.1 Factory default settings .......................................................................................................................... 20
5.2 Interaction between the HygroLab C1 and HygroClip 2 probe ............................................................... 21
5.3 User defined calculation ......................................................................................................................... 21
6 Maintenance..............................................................................................................................................22
6.1 Periodic calibration check of the HygroClip 2 probe ............................................................................... 22
6.2 Cleaning or replacing the probe dust filter .............................................................................................. 22
6.3 Firmware updates................................................................................................................................... 22
7 Probe Calibration and Adjustment Procedures .....................................................................................23
7.1 Overview ................................................................................................................................................ 23
7.2 Calibration against a known reference environment .............................................................................. 23
7.3 Calibration against a reference HygroClip 2 probe................................................................................. 24
7.4 Adjustment of humidity and temperature................................................................................................ 24
8 Technical data...........................................................................................................................................25
8.1 Specifications ......................................................................................................................................... 25
8.2 Dew point accuracy................................................................................................................................ 26
9 Accessories...............................................................................................................................................27
10 Supporting documents.............................................................................................................................27
11 Document releases...................................................................................................................................28
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
3
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Applicability:
This manual is valid for the HygroLab C1 with firmware version 1.xx, where 1.xx can be 1.0a, 1.1b etc.
Changes to the last two digits of the version number reflect minor firmware changes that do not affect the
manner in which the instrument should be operated.
1 Overview
The HygroLab C1 is a multifunction bench-top indicator that can read simultaneously up to 4 HygroClip 2
digital humidity-temperature probes. The HygroLab C1 is primarily designed for measuring the water activity
(Aw) of foods, pharmaceuticals and cosmetics. The HygroLab C1 can also be used in other laboratory
applications that require measuring humidity and temperature.
The HygroLab C1 is equipped with a digital interface. Depending on the option the HygroLab C1 has either a
USB or an Ethernet interface or with both.
The HygroLab C1 features two distinct operating modes:
Aw Measurement:This specialized mode is used for measuring the water activity (Aw) of product
samples and materials in bulk such as powders, seeds, etc. When set to operate in the water activity mode,
the HygroLab C1 automatically displays humidity as Aw (1.000 aw= 100 %RH). The Aw Mode offers the
following options:
Accelerated water activity measurement (AwQuick): permits measuring the water activity of
most products in typically 5 minutes. The measurement starts simultaneously for all four probe inputs
and is ended automatically.
Conventional water activity measurement (AwE): the measurement starts simultaneously
for all four probe inputs. The HygroLab C1 automatically detects full equilibrium conditions and ends
the measurement at that time.
The HygroLab automatically signals the end of each water activity measurement and offers the option of
automatically capturing both the end result and the value of temperature in 4 separate data bins (one non -
volatile memory per probe). Up to 500 records can be captured per probe and each record is stamped for date
and time. Data viewing can be done from the keypad and the data can be saved to a PC using the Rotronic
HW4 software.
Standard Mode:in this mode the HygroLab C1 can be used as a general purpose indicator with the
following functions:
oRelative humidity and temperature data measured by up to 4 HygroClip 2 digital probes
oCalculated humidity parameter such as dew / frost point or other, for up to 4 HygroClip 2 probes
oUp to 4 user defined calculations such as the difference between the temperature and the dew point
measured by a probe, the average of the temperature measured by two probes, etc.
The HygroLab C1 is available with a wide assortment of HygroClip 2 humidity-temperature probes to meet
almost any requirement. The HygroClip 2 probes feature well proven, durable sensors. Digital signal
processing ensures consistent product performance and also facilitates the task of field maintenance with
features such as potentiometer free digital calibration.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
4
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
2 General description
2.1 Configuration software
Most of the HygroLab C1 settings can be configured directly from the keypad. However, some of the settings
and access to some of the functions requires connecting the HygroLab C1 to a PC running the HW4 software
version 3.1 or higher, using either USB or Ethernet. For instructions see the following HW4 manual: E-M-
HW4v3-F2-019
2.2 Power supply
The HygroLab C1 requires the power adapter 12 VDC, 200 mA).
As an alternative, the HygroLab C1 can also be powered via the USB port (no power adapter - current draw:
about 70 mA). In this case, the Ethernet port is inactive and cannot be used.
2.3 Probe inputs
The HygroLab C1 has 4 probe inputs designed for use with all HygroClip 2 digital probes with the standard
UART interface (see also Back panel and digital interface options).
Pin-Out Diagram
2.4 Measured parameters
The HygroClip 2 probe measures relative humidity with a ROTRONIC Hygromer® IN1 capacitive sensor and
temperature with a Pt100 RTD.
2.5 Calculated parameters
The HygroLab C1 can calculate any of the following parameters based on the humidity and temperature
values measured by the probe (to select the calculated parameter, use either the keypad or the HW4 software
> Device Manager):
oDew point (Dp) above and below freezing
oFrost point (Fp) below freezing and dew point above freezing
oWet bulb temperature (Tw)
oEnthalpy (H)
oVapor concentration (Dv)
oSpecific humidity (Q)
oMixing ratio by weight (R)
oVapor concentration at saturation (Dvs)
oVapor partial pressure (E)
oVapor saturation pressure (Ew)
1: RXD (UART- digital probe)
2: GND (digital and power)
3: V+: 3.3 VDC nominal
4: Not used
5: Not used
6: Not used
7: TXD (UART digital probe)
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
5
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Note: calculating some of the above parameters requires barometric pressure as an input parameter. A fixed
barometric pressure value can be specified using either the keypad or the ROTRONIC HW4 software.
In addition, the HygroLab C1 can display for each probe input a user defined calculation such as the
difference between the temperature and the dew point measured by a probe, the average of the temperature
measured by two probes, etc. Configuration of the HygroLab C1 for a user defined calculation requires the
Rotronic HW4 software version 3.1 or higher (see separate document E-M-HW4v3-F2-019)
2.6 Alarm Indication on the display
Depending on the type of alarm, the display shows either a symbol or a text when the HygroLab C1 detects an
alarm condition:
oOut-of-limits value (defined with the HW4 software for each probe input, includes measured values
and calculated parameter).
oDisplay of fixed values when no probe is connected the input. Easily identified humidity and
temperature values can be specified with the HW4 software for each probe input.
oBad RH sensor or major sensor failure (open or shorted sensor humidity and temperature)
2.7 Real time clock
The HygroLab C1 clock keeps track of the date and time and can be adjusted from the keypad. Using the
HW4 software, the clock can be synchronized with the PC date and time. The clock does not automatically
adjust for daylight saving time (DST).
2.8 Back panel and digital interface
As an option, the HygroLab C1 is available with any of the following digital interfaces:
oUSB only (can be used to power the HygroLab C1)
oEthernet only (RJ45)
oUSB and Ethernet (only one interface can be used at any time)
Use of the Ethernet interface always requires the HygroLab to be powered with the AC1211 power adapter.
HygroLab C1 back panel showing the four probe inputs as well as the USB and Ethernet ports.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
6
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
3 Basic operation
3.1 Display
The LC display has a backlight which can be set to be on all the time or whenever a key is pressed. The
backlight can also be disabled.
Using the HygroLab C1 Menu > Display Settings > Mode, the display mode can be changed as shown below:
The display can also be configured to show a trend indicator on each line:
Both arrows: stable
In the event of an alarm the symbol [ ! ] appears to the right of the value.
When the display is set to display humidity and temperature and provided that the Aw mode is not enabled,
the bottom of the display shows the date and time. The probe input that is currently selected is always shown
at the bottom of the display.
NOTE: Using the HW4 software, each probe input of the HygroLab C1 can be configured to display a user
defined calculation instead of displaying a calculated psychrometric parameter such as the dew point. For
example, the HygroLab C1 can be configured to display the difference between the temperature of probe 1
and the dew point calculated for probe 1, whenever probe 1 is selected.
Standard:
o%RH
oTemperature
oDate and time
3-line display:
o%RH
oTemperature
oCalculated parameter
(see note below)
o
No date and time
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
7
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
3.2 Keypad
3.3 ON/OFF key
The ON/OFF key is used as follows:
oTo turn the instrument on: press the ON/OFF key
oTo turn the instrument off: press the ON/OFF key
ON/OFF:
Turns the instrument
on or off.
MENU: Activates the internal
menu. Press this key
again to go back to the
previous sub-
menu or to
exit the menu
UP / DOWN:
oSelects the probe being displayed
oWhen the menu is
active, use to navigate the menu,
make a selection or change a value
ENTER:
oWhen the menu is active, use to confirm the
selection of a menu item, effect a change of
settings and confirm any change
oIn the Aw Mode, use to start, hold or stop the
water activity measurement function
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
8
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
3.4 Internal menu
Note
(use the HW4 software > Device Manager > Display)
Main Menu
Menu Items
Submenu
Items
Selections or
Information
Notes
Device Info
Serial Nbr
Serial number
Version
Firmware version
Type
Device type
Name
Device name
User defined
Device Settings
Pressure
Fixed barometric pressure
value required for
calculating some
psychrometric parameters
Unit Sys
Metric / English
Ref. Probe
1 / 2 / 3 / 4
Reference probe input
used to adjust probes
connected to the other
inputs
Display Settings
Trend
ON / OFF
Trend indication on the
display
Decimals
1 or 2
Display resolution
Mode
H+T
H+T+Calc
See 4.1.1
Contrast
LC display contrast
adjustment
Back Light
Key Press/ON/OFF
Display backlight mode
Time Settings
Date
Press on ENTER when
highlighted and use UP or
Down to adjust
Date Fmt
dd mm yyyy
mm dd yyyy
yyyy mm dd
Date format
Separator
. or / or -
Date separator
Time
Press on ENTER when
highlighted and use UP or
Down to adjust
Time Fmt
24h / 12 h
Time format
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
9
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Main Menu
Menu Items
Submenu
Items
Selections or
Information
Notes
Aw Settings
Enable AW
ON / OFF
Enable = ON changes the
display as follows:
o
Humidity unit changes
to aw
oNo calculated
parameter
SaveResult
ON / OFF
ON: When the Aw
measurement is ended,
both the end result and
temperature are saved in
the following data bins:
Probe 1: to Bin 1
Probe 2: to Bin 2, etc.
Mode
AwQuick / AwE
oAwQuick: accelerated
water activity
measurement
oAwE: conventional
water activity
measurement
Dwell Time
minutes
Dwell time (AwQuick)
AwQ Temp
°C / minute
Temperature stability
definition (AwQuick)
AwE Temp
°C / minute
Temperature stability
definition (AwE)
AwE Humi
a
w
/ minute
Humidity stability definition
(AwE)
Data Storage
oDisplays the names of
the 4 data bins
Bin 1 = Probe 1
Bin 2 = Probe 2, etc.
o
Press on ENTER to
select the highlighted
data bin
View Samples
oShows the individual
data records
oUse the UP and
DOWN keys to
navigate the records
Summary
Shows the minimum,
maximum and average
values for the data bin
Clear Data
Clears the data bin
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
10
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Main Menu
Menu Items
Submenu
Items
Selections or
Information
Notes
Probe Settings
Calc 1
4
Psychrometric
Parameter. See 2.5
Calculated parameter
Probe 1, 2, 3, 4
Formula 1 4
ON / OFF
User defined calculation
Probe 1, 2, 3, 4
(requires HW4 software)
When ON, this calculation
replaces the psychrometric
parameter
both on the
local
on the display
and on
a PC monitor (HW4
software)
Probe Actions
Probe
Probe Input Number
Use to select a probe input
Probe Info
Serial Number
Version
Probe Name
Humidity Adjust
Show Acquired
Points
Lists the cal. points
present in the probe
memory (a max. of
10 points are
shown)
Additional Options:
oClear all cal. points
oClear the last point
Acquire (Ref
Probe
)
Saves value measured by
the reference probe as a
cal. point
Acquire (Ref
Value
)
Manual entry:
known reference
environment
Saves value entered
manually as a cal. point
Start
Adjustment
Adjusts the probe
Effect depends on number
of calibration
points in
probe memory
Reset to
Factory
Returns the probe to the
initial factory adjustment
Temperature
Adjust
Show Acquired
Points
Lists the cal. points
present in the probe
memory (a max. of 2
points are shown)
Additional Options:
oClear all cal. points
o
Clear the last point
Acquire (Ref
Probe
)
Saves value measured by
the reference probe as a
cal. point
Acquire (Ref
Value
)
Manual entry:
known reference
environment
Saves value entered
manually as a cal. point
Start
Adjustment
Adjusts the probe
Effect depends on number
of calibration points in
probe memory
Reset to
Factory
Returns the probe to the
original factory adjustment
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
11
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Main Menu
Menu Items
Submenu
Items
Selections or
Information
Notes
<
Set as Ref
.
Probe
>
Sets the probe connected
to the selected input as the
reference probe
NOTE: use the MENU key to go back one step from any sub-menu or to exit the entire menu (this may require
several key presses).
3.5 Frequently used settings
3.5.1 Unit system
Press the MENU key and select Device Settings > Unit Sys. Press ENTER to activate the Unit Sys menu item,
use the UP or DOWN arrow key to change the unit system. Press ENTER to confirm and press MENU to exit.
The HW4 software can also be used to change the unit system.
WARNING: changing the unit system does not change the numerical value of the fixed barometric pressure
used in some psychrometric calculations. Always verify and modify as required the numerical pressure value
after changing the unit system.
3.5.2 Date and time
Press the MENU key and select Time Settings > Date or Time. Press ENTER to activate either the Date or the
Time menu item, use the UP or DOWN arrow key to change the Date or the Time. After each change, the
cursor moves to the right. When done, press ENTER to confirm and press MENU to exit.
To change either the date or the time format, Press the MENU key and select Time Settings > Date Fmt or
Time Fmt. Press ENTER to activate either the Date Fmt or the Time Fmt menu item, use the UP or DOWN
arrow key to change the Date or the Time format. When done, press ENTER to confirm and press MENU to
exit.
The HW4 software can also be used to set the clock of the HygroLab C1 to the PC date and time.
3.5.3 Select the calculated parameter for a probe input
Press the MENU key and select Probe Settings > Calc1 to Calc 4. Press ENTER to activate the Calc sub-
menu, use the UP or DOWN arrow key to select the calculated parameter. Press ENTER to confirm and press
MENU to exit.
3.5.4 Select which probe and/or parameters are shown on the display
Press the MENU key and select Display Settings > Mode. Press ENTER to activate the Mode menu item, use
the UP or DOWN arrow key to select the display mode. Press ENTER to confirm and press MENU to exit.
Use the UP or DOWN arrow key to change the probe being displayed.
NOTE: The calculated parameter is shown only if enabled for the probe input that is selected (MENU >
Probe Settings).
3.6 Connecting the HygroLab C1 to a PC
USB connection: connect the HygroLab C1 to the USB port of a PC with the ROTRONIC HW4 software
installed. Note that the ROTRONIC USB driver must be installed on the PC prior to connecting the HygroLab
C1 as explained in the HW4 manual E-M-HW4v3-Main. Both the driver and the installation instructions are
located on the HW4 CD and are also available from the Rotronic website.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
12
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
Ethernet connection: use of the Ethernet interface requires configuring the HygroLab C1 so as to ensure
compatibility with the LAN to which the HW4 PC is connected. See document E-M-TCPIP-Conf available from
our website.
3.7 Practical advice for measuring humidity
The most common source of error when measuring relative humidity is a difference between the temperature
of the probe and the temperature of the environment. At a humidity condition of 50 %RH, a temperature
difference of 1 C (1.8 F) typically results in an error of 3 %RH on relative humidity.
It is always good practice to monitor the display for temperature stability. The probe should be given sufficient
time to equilibrate with the environment to be measured. The larger the initial temperature diffe rence between
the probe and the environment to be measured, the more time temperature equilibration requires. This time
can be shortened, and errors avoided, by using the probe configuration that fits best for your application.
In extreme situations, condensation may occur on the sensors when the probe is colder than the environment.
As long as the humidity / temperature limits of the humidity sensor are not exceeded, condensation does not
alter the calibration of the sensor. However, the sensor has to dry out before it can provide a valid
measurement.
Non-moving air is an excellent insulator. When there is no air movement, surprising differences in temperature
and humidity can noted over short distances. Air movement at the probe generally results in measurements
that are both faster and more accurate.
4 Aw Measurement
When enabled to measure water activity, the HygroLab C1 automatically displays humidity as Aw (1.000 aw=
100 %RH) and offers the following options:
AwE mode: the HygroLab C1 waits for the full equilibration of the measured product and probe. For most
products, this takes from 30 to 60 minutes. The HygroLab C1 automatically detects equilibrium conditions
(humidity and temperature) and ends the measurement at that time by freezing the display.
AwQuick mode: the HygroLab C1 uses an algorithm to accelerate the water activity measurement and
provides a result in typically 5 minutes. The measurement ends automatically and the display is frozen. When
temperature conditions are stable (both at the product and probe), the value measured with the AwQuick
mode is generally within ± 0.005 aw of the value that would be obtained by waiting for full equilibration of the
product and probe.
NOTE: See technical paper E-T-AW (Measuring Water Activity) for basic information on water activity and its
applications.
4.1 Enabling Aw Measurement
To enable the HygroLab C1 to measure water activity:
oAw Settings
oEnable Aw item highlighted, press ENTER and use the UP or DOWN arrow key to
select ON. Press ENTER to confirm the selection.
oSaveResult
the UP or DOWN arrow key to select either ON or OFF. Press ENTER to confirm the selection
oMode
arrow key to select either AwQuick or AWE. Press ENTER to confirm the selection.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
13
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
oThe settings for either the AwQuick or AWE function can be changed after using the UP or DOWN
arrow key to highlight the setting and by pressing on ENTER. Use the UP or DOWN arrow key to
change each digit. Press ENTER to move the cursor to the right. When done, press ENTER to save
the value.
oPress MENU twice to fully exit the menu.
4.2 Water activity measurement settings:
Setting
Applies to
Notes
Dwell Time
AwQuick
The HygroLab C1 waits the specified amount of time before processing the
humidity data with the AwQuick algorithm.
Recommended value: 3 or 4 minutes.
AWQ-Temp
AwQuick
The HygroLab C1 considers temperature to be stable when the rate of
change of the temperature signal is less than the specified value.
Recommended value: 0.01 C / min
AWE-Temp
AwE
The HygroLab C1 considers temperature to be at equilibrium when the rate
of change of the temperature signal is less than the specified value.
Recommended value: 0.01 C / min
AWE-Humi
AwE
The HygroLab C1 considers humidity to be at equilibrium when the rate of
change of the humidity signal is less than the specified value.
Recommended value: 0.0001 Aw / min
SaveResult
AwQuick
AwE
When the Aw measurement is ended, the result is saved in the following
dat
a bins:
Probe 1: Bin 1, Probe 2: Bin 2, Probe 3: Bin 3, Probe 4: Bin 4
4.3 Aw probe usage guidelines
1) HC2-AW probe: check that the red LED on top of the probe is lit. This indicates that the probe is being
powered. If necessary, power the probe by pressing once on the red button located on top of the probe.
When the red LED is not lit, the HC2-AW probe is not powered and the instrument is not receiving a
signal from the probe.
2) Measuring with less than 4 probes: both the AwQuick and AwE functions run simultaneously for all
HygroLab C1 probe inputs. We strongly recommend to either disconnect or to power down any unused
probe.
IMPORTANT:
oThe measurement starts simultaneously for all probe inputs (disconnect or power off any
unused probe)
oUsually, the measurement ends at a different time for each probe. When using multiple probes, the
HygroLab C1 emits a short beep whenever a probe is done measuring. A long beep indicates that the last
probe is done. When Data Storage is enabled, the end result of each probe end result is stored in
memory (bins 1 to 4)
oEach probe can be displayed by using the UP or the DOWN key
oPressing ENTER resets all probe inputs and discards any measurement result that has not been stored.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
14
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
4.4 Using the AwQuick mode
The HygroLab C1 uses an algorithm to project the full equilibrium value (water activity) of the product sample:
1) The value of the humidity signal is constantly monitored
2) The stability of the temperature signal is constantly monitored
3) After an initial period of time (dwell time), the humidity data is used to project the end value of the
equilibration process (water activity). The measurement ends automatically as soon as the projected
Aw value is stable. At that time, the HygroLab C1 freezes the display.
The measurement is automatically ended and typically requires about 5 to 6 minutes.
With the default dwell time of 4 minutes, the difference between the AwQuick function and the conventional
measurement method is typically 0.005 aw or less. The value of the dwell time can be set by the user (see
SETTINGS) and is a tradeoff between speed of measurement and accuracy. Generally, a longer dwell time
produces more accurate results but causes measurements to take longer.
The value of temperature shown at the end of the measurement is the average temperature during the
measurement. The HygroLab C1 displays a trend indicator to the left of the temperature value. This is used to
verify that temperature was stable during the measurement.
1. AWQ Reset: the HygroLab C1 is ready to start measuring all connected probes
When ready to measure, press on the ENTER key.
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
15
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
2. AWQ Dwell
3. AWQ Running HygroLab C1 starts projecting the end result
Current
humidity value
Current
temperature value
AwQuick mode is
in the dwell phase
Probe 1
is being displayed
Elapsed time
hh:mm:ss
Average
temperature
Current
Aw projection
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
16
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
4. AWQ Ended: when the projection is stable for a probe being displayed, the HygroLab C1 automatically
ends the measurement and freezes the display for that probe. A check mark appears to the left of the water
activity value. In addition the HygroLab C1 can be set with the HW4 software to emit an acoustic signal (Beep)
lasting 5 seconds when the last probe is done. The acoustic signal can be stopped by pushing a key (do not
press the ENTER key).
When several probes are connected to the HygroLab C1, use the UP or DOWN key to view each probe.
IMPORTANT: do not press the ENTER key until you have reviewed each probe.
5. AWQ Reset: write down the measurement for each probe or use the automatic data capture function. This
function can be enabled from the keypad: MENU > Aw Settings > SaveResult > ON. The Aw value measured
by probe 1 is saved to Data Bin 1. Probe 2 is saved to Data Bin 2, etc.
Press ENTER. The HygroLab C1 is ready to start a new measurement
Measurement ended
Final
Aw projection
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
17
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
4.5 Using the AwE mode
The HygroLab C1 monitors the water activity and temperature values measured by the probe. When both
values are at equilibrium during a few minutes, the measurement is automatically ended. Depending both on
the product being measured and on the stability of temperature, measurements typically require 30 to 60
minutes.
1. AWE Reset: the HygroLab C1 is ready to start a measurement using up to 4 probes
When ready to measure, press on the ENTER key.
2. AWE Running: the HygroLab C1 starts monitoring the humidity and temperature signals for equilibrium
Current
humidity value
Current
temperature value
AwE mode is running
Probe 1
is being displayed
Elapsed time
hh:mm:ss
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
18
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
3. AWE Ended: when both the humidity and temperature signals measured by a probe are stable, the
HygroLab C1 automatically ends the measurement and freezes the display for that probe. A check mark
appears to the left of the water activity value. In addition the HygroLab C1 can be set with the HW4 software
to emit an acoustic signal (Beep) every 5 seconds when the last probe is done. The acoustic signal can be
stopped by pushing a key (do not press the ENTER key).
When several probes are connected to the HygroLab C1, use the UP or DOWN key to view each probe.
IMPORTANT: do not press the ENTER key until you have reviewed each probe.
4. AWE Reset: write down the measurement for each probe or use the automatic data capture function. This
function can be enabled from the keypad: MENU > Aw Settings > SaveResult > ON. The Aw value measured
by probe 1 is saved to Data Bin 1. Probe 2 is saved to Data Bin 2, etc.
Press ENTER. The HygroLab C1 is ready to start a new measurement
Measurement ended
Final
Aw measurement
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
19
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
4.6 Viewing the captured data (automatic data capture enabled)
Press the MENU key and select Data Storage. See 3.4 Internal Menu for instructions.
oView Samples: view individual data records
oSummary: view the maximum, minimum and average values
oClear Data: erase the contents of the data-bin
Press MENU to exit.
The captured data can be saved to a PC running the Rotronic HW4 software v3.1 or higher (see separate
document E-M-HW4v3-F2-019)
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]

E
-M-HyLabC1-V1_10
Rotronic AG
Bassersdorf, Switzerland
Document code
Unit
HygroLab C1 bench-top indicator:
User Guide
Instruction Manual
Document Type
Page
20
of 28
Document title
© 2011; Rotronic AG E-M-HyLabC1-V1_10
5 User configurable settings and functions
The HygroLab C1 can be used just as any conventional humidity and temperature indicator. Making use of the
HygroLab C1 configurable settings and functions is entirely up to the user and the appropriate settings depend
on the user application. We have provided below a short description of the HygroLab C1 functions and also
indicated the factory default settings.
5.1 Factory default settings
Notes:
oConfiguration of the HygroLab C1 and probe by the user and access to its functions requires a PC with
the ROTRONIC HW4 software (version 3.1 or higher) installed. Any available digital interface option can
be used to connect the HygroLab C1 to the PC.
oSettings and functions that can also be accessed from the keypad are marked with the letter K(see also
Operation > Internal Menu).
HygroLab C1 Configurable Settings
Factory default
Device write protection
Disabled
RS-485 address
0
Device name
Instrument model
Fixed barometric pressure value
K
1013.25 hPa (29.92 In Hg or 14.70 PSI)
Date and time
K
Time zone dependent
Unit system (Metric or English)
K
Metric, except USA: English
Date and time format, date separator
K
European format (except North America)
Input name
Probe 1, Probe 2, Probe 3 or Probe 4
Psychrometric calculation for the input
K
No calculation
Display backlight
K
On Key Press
Displayed parameters / display mode
K
Humidity and temperature + date and time
Display resolution
K
2 decimals
Trend indicator (display)
K
Enabled
Menu access from keypad
Enabled
User Defined Calculation
K
Disabled
Humidity / temperature calibration
K
Enabled
Humidity / temperature adjustment
K
Enabled
Aw Measurement
K
Disabled
Automatic data capture (Aw measurement)
K
Disabled
Device write protection
Disabled
Out-of-limit values alarm
Disabled
Monitor sensor alarms
Enabled (this function cannot be disabled)
Simulator mode (fixed values)
Disabled
For a detailed description of all HygroClip 2 probe (AirChip 3000) functions see document
E-T-AC3000-DF-V1
Instructions regarding the configuration of the HygroLab C1 and probes as well as access to the functions are
provided in the following manuals:
QAQC LAB 589 Rappahannock Drive White Stone Va 22578 TEL [phone]