Rovo kids Electric ride-on toy atv User manual

Electric Ride-On Toy ATV

User Manual

[Revision 3.0 May 2018]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

Electric Ride-On Toy ATV

Safety

Read and understand all safety warnings and instructions before assembling or using the

electric ride-on car ("toy"). The instructions not only specify the assembly process and

proper operation, but also help you to avoid injuries or damaging the product due to incorrect operation.

•Choking hazard – small parts included. Not suitable for children under 3 years of age.

•Use the toy under adult supervision. Although most children can master the skills required to

control the toy, they do not have mature judgment skills. Never let a child use the toy at any time

without adult supervision. Take the time to carefully evaluate the child's skill levels and abilities

to operate the toy safely. Children cannot always recognize hazards even after instruction, so

teach appropriate safety rules before allowing any child to operate the toy.

•Maximum load capacity = 30kg.

•An adult should inspect the toy at regular Intervals for wear or loose fasteners etc, and tighten as

required. Do not use the toy if abnormal conditions such as cracks or breaks exist.

•Do not operate the toy on public streets or roads, near moving vehicles, steep inclines or steps, near

swimming pools, or any other potentially dangerous areas.

•The toy is designed for outdoor use on suitable surfaces and in dry conditions. Do not operate in the

dark, on sand or gravel, dirt, grass, uneven or rough ground. Running the toy indoors may cause

damage to flooring or other items.

•The remote control should only be operated by adults or under adult supervision.

•When the remote control batteries are running low, the effective range of the remote control is reduced.

Replace with new batteries.

•This toy must not be overloaded or used to push or pull other objects.

•This toy is suitable for children aged 3 and up.

•Some parts of the toy may be damaged due to improper operation.

•Do not suddenly switch between forward and reverse when the toy is moving. Switch between forward

and reverse only when the toy is stationary.

•Clean the toy with a soft, clean cloth. Do not spray or immerse the toy with water, which might damage

the electronics.

•This product is made of plastics. Keep it away from fire or other sources of heat.

•The electric motors may produce sparks. Do not run the toy in flammable and explosive areas such as a

petrol station.

•Do not allow children near or to touch moving parts when the toy is running.

•The packaging is not a toy and should be disposed of responsibly.

•Adults are required to read these instructions carefully and give correct guidelines to children on how to

safely operate the toy before using it. Instruction should include:

•Starting, stopping and steering.

•One rider only at a time, and always sit in the seat.

•Wear shoes.

•Do not place hands, feet or any part of the body, clothing or other articles near moving parts while

the toy is in operation.

•If the toy malfunctions, do not use it until it is repaired.

•Thermal Fuse - The toy is equipped with a built-in thermal fuse. The fuse is a self-resetting safety

device that shuts down the toy if it is overloaded. Once a fuse has tripped it will automatically reset after

approximately 10 seconds and allow the toy to resume normal operations. To avoid repeated tripping, do

not overload the toy by exceeding the maximum weight capacity. Avoid inappropriate driving conditions,

Electric Ride-On Toy ATV

such as steep slopes or against fixed objects, which can cause the wheels to stop spinning while power

is being supplied to the motors. If a thermal fuse in continually trips under normal operating conditions

and loads, have the toy inspected by an authorised service centre.

Battery Safety and Charging

Failure to follow instructions on correct battery maintenance may permanently damage the

batteries and will void the warranty.

•Never modify the electrical system. Alterations may cause malfunction, fire, serious injury and/or

property damage.

•Charge the batteries for 10 hours before first use.

•Do NOT charge the batteries for longer than 10 hours continuously .

•Do NOT short-circuit batteries or battery supply terminals.

•Do NOT expose batteries to excessive heat, flammable or corrosive substances.

•Do not store batteries in temperatures above 40°C (104°F) or below -23°C (-10°F).

•Charge the batteries at least monthly, even if the toy is not in use.

•Over-charging or under-charging the batteries may shorten battery life and decrease toy running time.

•Do not allow the batteries to discharge completely before charging.

•Charge the batteries after each use, regardless of how long the toy was used.

•The battery compartment is not a storage areas. Storing other articles may create a fire hazard.

•If battery acid is ingested, call a physician immediately and give water or milk. Do not induce vomiting.

•Install batteries correctly and according to polarity.

•Remove the batteries if the toy is not be used for an extended period of time.

•Dispose of used batteries in an environmentally responsible manner and according to regulations.

•Do NOT burn or dispose of batteries in a fire.

•Use of the wrong type battery or charger may cause a fire or explosion resulting in serious injury. Only

batteries of the same or equivalent type as recommended are to be used.

•Batteries must be handled by adults only. Batteries are heavy and contain sulphuric acid (electrolyte).

Dropping batteries could result in serious injury.

•Leaving the batteries in a discharged condition will destroy them.

•If the toy will be stored for more than 2 months, disconnect the motor harness from the batteries.

•Battery charging or replacement must be performed by adults only.

•Never lift or carry batteries by wires or connectors. This can damage the battery and possibly cause a

fire. Lift and carry batteries by the case only.

•Read all safety instructions on the battery.

•Examine the battery charger, leads, plug and connectors for wear or damage each time you use it. If any

damage or wear is detected, do not use the charger until it is repaired or replaced.

•Ensure the voltage and frequency of the charger is compatible with mains electrical supply.

•Only use the battery charger in dry locations.

•Never recharge non-rechargeable batteries.

•Batteries can fall out and cause injury if the toy overturns. Always use the battery brackets and cover

(seat).

•Batteries must be upright while charging – ensure the toy is sitting on a flat surface when being charged.

Electric Ride-On Toy ATV

•Periodically examine the batteries (remove the seat) for cracks or damage which may cause sulphuric

acid (electrolyte) to leak during charging. If damage is detected, do not charge the battery or use it.

Battery acid is highly corrosive and can cause severe injury to persons and damage to surfaces it

contacts. If battery acid comes in contact with skin or eyes, call a physician immediately and flush with

cool water for at least 15 minutes.

•Do not charge batteries on surfaces that could be damaged by battery acid. Take precautions to protect

surfaces where batteries are charged.

•If the batteries are old and will not accept a charge, remove them from the toy. Always remove

unserviceable batteries.

Battery Charging

1. Insert the battery charger connector into the charger port

located at the rear of the toy.

2. Plug the charger into a standard 240VAC wall socket and

switch it ON. The charger may feel warm during charging.

This is normal and not a cause for concern.

3. After charging is complete, unplug the charger from the wall

outlet and unplug the battery connector from the charger port.

Electric Ride-On Toy ATV

Table of Contents

Safety...................................................................................................................................................2

Battery Safety and Charging ............................................................................................................3

Battery Charging ........................................................................................................................................4

Parts Identification.............................................................................................................................6

Assembly ............................................................................................................................................7

Operation ..........................................................................................................................................10

Controls....................................................................................................................................................10

Driver Mode Operation............................................................................................................................. 10

Troubleshooting...............................................................................................................................11

Maintenance .....................................................................................................................................12

Specifications...................................................................................................................................12

Electric Ride-On Toy ATV

Parts Identification

Identify all parts before assembly and save all packaging material until assembly Is completed to

ensure that no parts are discarded. • Metal parts may be coated with lubricant for protection during

shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. • Assemble the toy

according to instructions. Due to manufacturing techniques it is possible that some parts are over-supplied. •

Screwdrivers may be required for assembly.

No. Name No. Name

1 Body 9 Fasteners / Accessories:

4 x Wheel Nut

1 x Machine Screw (Seat)

8 x Axle Washer

2 x Axle Bush

4 x Wheel Nut Cover

8 x Self-Tapping Screw

1 x Split Pin

Battery Charger

2 x Wheel Nut Spanner

2 Rear (Driven) Wheel (2)

3 Front Wheel (2)

4

Rear Axle

5

Front Axle Assembly

6

Steering Shaft

7 Handlebar

8 Seat

5

1

4

2

7

8

6

3

9

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

Assembly

Children may be harmed by small parts, sharp edges and

points or electrical components when the toy is not assembled. Care should be taken to not allow

children near parts when unpacking and assembling the toy. • The toy should be assembled by an adult or

checked by an adult to ensure that it is properly assembled.

1. Turn the toy over to install the rear axle and the rear

(driven) wheels.

•Insert the rear axle (A) through the drive gears (B)

and toy body. Ensure it is centred with the toy body.

•Place the driven wheels (C) on to each end of the rear

axle, with the drive gear (D) facing inward, then place

an axle washer (E) on the axle, then screw (rotate

right) a wheel nut (F) on to the axle and tighten using

the supplied wheel nut spanner. Ensure that the

wheels are secure, however, the nuts are not so tight

as to prevent the wheels from being driven.

2. Install the front axle assembly and steering shaft.

•Place the front axle assembly (H) into position as shown so the mounting brackets align with the

mounting points on the toy body. Attach the front axle assembly to the toy body using 8 self-tapping

screws. Tighten (rotate right) the screws using a Phillips head screwdriver, however, be careful not

to over-tighten the screws as they are screwing into plastic.

•Place an axle washer (E) onto the straight end of the steering shaft (I), then insert the steering shaft

(I) into the toy body through the steering hole (J). Insert the hooked end of the steering shaft into the

hole (K) at the rear of the front axle assembly. On the end of the steering shaft, place an axle washer

(E) and prevent it from falling out by inserting a split pin (L) through the hole in the shaft. Bend the

legs of the split pin out so it cannot fall out. The purpose of the washer and split pin is to ensure the

steering shaft is always engaged with the front axle assembly

H

E

F

Video Tutorial:

Typical Ride-On Car Assembly

K

A

B

D

C

I

K

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

3. Install the front wheels.

•Place an axle washer (E) and axle bush (M) on to each front axle (N).

•Place a front wheel (O) onto each axle, then place an axle washer (E) on the axle, then screw (rotate

right) a wheel nut (F) onto the axle and tighten using the supplied wheel nut spanner. Ensure that the

wheels are secure, however, the nuts are not so tight as to prevent the wheels from spinning freely.

•On all wheels, install the wheel nut covers (G) by aligning the tabs on

the cover with the slots in the wheel then pressing the cover in until it

"clips" into place.

4. Install the handlebar.

•Remove the screw and nut from the handlebar stem.

•Ensure the front wheels are straight then slide the handlebar (P) onto the steering shaft (Q) – ensure

that the handlebar stem screw hole aligns with the hole in the shaft.

•Insert the nut (R) into the recess in the handlebar stem. Insert the screw (S) from the other side of

the handlebar stem, passing through the steering shaft and into the nut. Adequately tighten the

screw with an appropriate screwdriver.

E

M

O

J

L

E

F

G

P

S

R

Q

O

N

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

5. Connect the battery.

•Firmly push the unconnected battery wire (T) onto the free battery

terminal (U). Once connected, the battery can be charged using the toy

charging port.

6. Install the seat (this also acts as a battery cover).

•Ensure no wires can be crushed or pinched when the seat is installed.

•Insert the tab (V) at the front

of the seat (W) into the

corresponding slot in the toy

body, then attach the back of

the seat to the toy body using

1 machine screw. Tighten

(rotate right) the screws using

a Phillips head screwdriver,

however, be careful not to

over-tighten the screw as it is

screwing into plastic.

7. Install the "sounds" battery.

•On the underside of the handlebar

(P) (left side), using a suitable

screwdriver remove the screw (rotate

left) securing the battery cover (X).

Remove the cover and insert 2 AA

batteries (ensure battery polarity is

correct) into the compartment. Re-

install the cover and secure with the

screw. Do not over-tighten the screw

as it is screwing into plastic.

Assembly is now complete.

V

W

T

U

P

X

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

Operation

Controls

No. Name Description

1 Direction / Speed Control Use to set the direction of travel and speed:

High –Travel forward at highest speed.

Low – Travel forward at slowest speed.

Backward – Travel backwards at slowest speed.

2 Accelerator Press to travel in the direction set using the direction control (forward or

reverse). Release to stop.

3 Horn Sounds Press for "horn" sounds.

4 Music Press for various in-built songs.

Driver Mode Operation

1. Ensure the “rider” is correctly and safely seated on the toy.

2. Select the direction and speed of travel using the direction / speed control.

3. Press the accelerator pedal to begin moving. Release the accelerator to stop.

1

3

2

4

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

Troubleshooting

Malfunction Analysis Solution

Toy not running or

was running but

suddenly stopped

1. Fuse tripped.

2. Electrical connections

not secure.

3. Dead battery.

4. Under-charged battery.

5. Battery charger not

working.

6. Electrics or switches

damaged.

1. Toy overloaded or used on unsuitable surfaces. Fuse

resets after 10 seconds. Unload toy (30kg max.) and/or

move to suitable surface.

2. Check all wires and connections. Ensure the electrical

harness is fully connected. Ensure no motor wires are

loose or disconnected.

3. Battery no longer serviceable. Have battery checked by

an authorised service centre or replace.

4. Charge battery and ensure battery charging and care

procedures are followed.

5. Have charger professionally checked. If not working –

replace.

6. Seek diagnosis and repair from authorised service

centre.

Short operating time

– less than 1 hour

per charge

1. Under-charged battery.

2. Over-charged battery.

3. Old or faulty battery will

not take full charge.

1. Charge battery and ensure battery charging and care

procedures are followed.

2. Battery no longer serviceable. Have battery checked by

authorised service centre or replace.

3. Expected battery life is 1 to 3 years depending on care,

use and conditions. Have battery checked by authorised

service centre or replace.

Movement is

sluggish

1. Under-charged battery.

2. Old or faulty battery will

not take full charge.

3. Toy overloaded.

1. Charge battery and ensure battery charging and care

procedures are followed.

2. Expected battery life is 1 to 3 years depending on care,

use and conditions. Have battery checked by an

authorised service centre or replace.

3. Toy overloaded or used on unsuitable surfaces. Unload

toy (30kg max.) and/or move to suitable surface.

Intermittent running 1. Electrical connections

not secure.

2. Main body electrics or

switches damaged.

1. Check all wires and connections. Ensure vehicle and

battery electrical harness is fully connected. Ensure no

motor wires are loose or disconnected.

2. Seek diagnosis and repair from authorised service

centre.

Vehicle requires a

push to get running

1. Electrical connections

not secure.

2. Motor has “dead” spot.

1. Check all wires and connections. Ensure the electrical

harness is fully connected. Ensure no motor wires are

loose or disconnected.

2. Seek diagnosis and repair from authorised service

centre.

Gear box noisy Broken or damaged gears. Seek diagnosis and repair from authorised service centre.

Battery gets warm

during charging

Normal operation. None required

Faint sounds and

heating from battery

when charging

Normal chemical reaction. None required

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

Maintenance

•If the toy is damaged, do not use it until it is repaired.

•An adult should inspect the toy at regular Intervals for wear or loose fasteners and tighten as required.

Do not use the toy if abnormal conditions such as cracks or breaks exist.

•The toy should be assembled by an adult or checked by an adult to make sure that it is properly

assembled.

•Clean the toy with a clean cloth only. Do not use abrasives, solvents or harsh detergent when cleaning.

Do not spray or immerse the toy in water as this will damage the electronics.

Specifications

Net Weight 20kg

Battery Type 12V 7Ah

Charger Type 12VDC 1000mA (output)

Range 1 to 2 hours (full charge)

Charge Time 8 to 10 hours generally (full charge)

Maximum Rider Weight 30kg

ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS ROVOKIDS

Electric Ride-On Toy ATV

Some experts believe the incorrect or prolonged use of almost any product could cause serious

injury or death. For information that may reduce your risk of serious injury or death, consult the

points below and additionally, the information available at www.datastreamserver.com/safety

•Consult all documentation, packaging and product

labelling before use. Note that some products feature

online documentation which should be printed and kept

with the product.

•Check product for loose / broken / damaged / missing

parts, wear or leaks (if applicable) before each use.

Never use a product with loose / broken / damaged /

missing parts, wear or leaks (if applicable).

•Products must be inspected and serviced (if applicable)

by a qualified specialist every 6 months assuming

average residential use by a person of average weight

and strength, above average technical aptitude, on a

property matching average metropolitan specification.

Intended use outside these guidelines could indicate

the product is not suitable for intended use or may

require more regular inspection or servicing.

•Ensure all possible users of the product have

completed an industry recognized training course

before being given access to the product.

•The product has been supplied by a general merchandise retailer that

may not be familiar with your specific application or your description

of the application. Be sure to attain third-party approval for your

application from a qualified specialist before use regardless of prior

assurances by the retailer or its representatives.

•This product is not intended for use where fail-safe operation is

required. As with any product (take an automobile, aircraft, computer

or ball point pen for example), there is always a small chance of

technical issues that needs to be repaired or may require replacement

of the product or a part. If the possibility of such failure and the

associated time it takes to rectify could in any situation inconvenience

the user, business or employee then the product is not suitable for

your requirements. This product is not for use where incorrect

operation or a failure of any kind, including but not limited to a

condition requiring product return, replacement, service by a

technician or replacement of parts could cause a financial loss, loss of

employee time or an inconvenience requiring compensation.

•If this item has been purchased in error after considering the points

above, simply contact the retailer directly for details of their returns

policy, if required.

ideas, diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Rovo Kids Electric Ride-On Toy ATV User manual

Popular Motorized Toy Car manuals by other brands