Rowenta DZ9030 User manual

NL
BG
CZ
SR
HR
RO
SK
TR
S
DK
PL
SLO
H
AR
www.rowenta.com
model DZ9030
COUV_DZ9000_14Langues 22/02/06 11:42 Page 1

5
9*
7
8
10*
12
13
14
4
3
3a 3d3c3b
2
1
11a* 11c*
11d*
11b*
6*
COUV_DZ9000_14Langues 22/02/06 11:42 Page 2

fig. 1 fig. 2 fig. 3
fig. 4 fig. 5 fig. 6
fig. 7 fig. 8
NONO OKOK
fig. 9
NONO OKOK
fig. 10 fig. 11 fig. 12
COUV_DZ9000_14Langues 22/02/06 11:42 Page 3

fig. 13 fig. 14
fig. 15
fig. 16 fig. 17 fig. 18
fig. 19
NONO
OKOK
fig. 20
COUV_DZ9000_14Langues 22/02/06 11:42 Page 4

3
1 Spray nozzle
2 Filling inlet
(with slide-button opening)
3 Variable steam control
a Dry ironing
b Smooth steam
c High Pressure steam
d Self Clean
4 Spray button
5 Shot of steam button
6 Auto-off indicator light*
7 Cord
8 Handle
9 Thermostat control light *
10
Temperature control dial
11 LED display *
a
Yellow LED
b Green LED
c Red LED
d Auto-off LED
12 Water tank
13 Maximum water level
indicator
14 Microsteam400 soleplate
DESCRIPTION
SAFETY INSTRUCTIONS
This appliance complies with the technical rules and standards
for safety currently in force (Electromagnetic Compatibility,
Low Voltage, Environment).
The appliance may only be connected to alternating current as
specified on the rating plate. Only safe extension leads should
be used.
An electrical appliance is not a toy. Use and store the appliance out
of reach of children. Do not let the supply cord hang down.
Do not leave the appliance unattended while it is connected to the
mains supply.
Electrical appliances generate high temperatures. Always use the
handle and warn other users of the potential dangers (e.g. escaping
steam or hot water, especially when ironing vertically).
Never direct steam at persons or animals, never treat clothing
which is being worn.
Always disconnect the appliance before filling or emptying the
water tank; before leaving the room (even for a short time); before
cleaning the appliance and after use.
Never unplug the appliance by tugging on the cord.
Do not immerse the appliance in water.
An electrical appliance should not be used if:
– the appliance is not functioning correctly;
– the appliance, the supply cord or the cord protector is damaged;
– the appliance has been dropped;
* depending on model
GB
DZ9000-11038999469 2/03/06 14:29 Page 3

4
3
P
to
A
te
U
ta
To
ir
th
fe
im
M
1
W
m
U
4
T
m
th
5
S
te
– the appliance is obviously leaking. In these cases the appliance
should be returned to an approved Rowenta Customer Service
Centre for repair. (See enclosed Service Centre addresses.) Repairs
to electrical appliances may only be carried out by specialists.
Improperly carried out repairs can cause serious danger to users.
To avoid danger to users, a defective or damaged supply cord
may only be replaced by an authorised Rowenta Customers
Service Centre .
This product has been designed for domestic use only.
Any commercial use, inappropriate use or failure to comply
with the instructions, the manufacturer accepts no responsibility
and the guarantee will not apply.
Environment protection first !
Your appliance contains valuable materials which
can be recovered or recycled.
Leave it at a local civic waste collection point.
Keep these instructions
BEFORE USE
1 • Unpacking
Take the iron out of the box and remove all the stickers.
2 • What water may be used ?
Your iron has been designed to operate using untreated tap water
up to 17° dH (German water hardness) or 3 mmol/liter. However, if
your water is very hard, you can mix 50% untreated tap water with
50% distilled or demineralised water.
IMPORTANT Before doing anything else, remove the soleplate
protector (fig.1)!
IMPORTANT Heat concentrates the elements contained in
water during evaporation.The type of water listed below
DZ9000-11038999469 2/03/06 14:29 Page 4

5
3 • Using for the first time
Plug in the iron (fig.2) and set the temperature control dial (fig.3)
to ••• to heat the appliance.
A little smoke and a slight smell may be emitted, but this is only
temporary.
Unplug the iron (fig.4) and fill the water tank (§ 4 Filling the water
tank).
To remove any impurities in the iron's steam chamber, unplug the
iron and hold it over a sink horizontally. Push the steam control into
the Self Clean position : steam will now begin to build up. After a
few seconds water will emerge from the soleplate, rinsing any
impurities out of the steam chamber (fig.5).
Move the steam control to steam position after approx.
1 minute. Plug in the iron and allow the iron to heat up again.
Wait until the remaining water has evaporated. Unplug from the
mains and allow the iron to fully cool down.
contain organic waste or mineral elements that can cause
spitting, brown staining or premature wear of the appliance:
- water from clothes dryers, scented or softened water, water
from refrigerators, batteries or air conditioners, pure distilled
or demineralised water or rain water should not be used in
your iron. Also do not use boiled, filtered or bottled water.
USE
4 • Filling the water tank
Tilt the iron. Open the filling inlet (fig.6). Pour in water up to the
max mark (fig.7). Close the filler inlet (fig.8) and return the iron to
the horizontal.
5 • Setting the temperature
Set the iron temperature to suit the type of material using the
temperature control dial (fig.3).
IMPORTANT Before filling the water tank, unplug the iron and
set the steam control to dry position .
s
h
DZ9000-11038999469 2/03/06 14:29 Page 5

6
7
Y
q
c
W
is
8
Y
(f
th
T
T
T
te
9
(f
P
st
1
(f
H
c
1
P
1
It
is
*
Temperature control*:The temperature control light indicates that
the soleplate is heating up. When the temperature control light goes
off (fig.9), the set temperature is reached and you can begin ironing.
Electronic temperature control*:The traffic lights tell you whether
the soleplate is at the selected temperature (fig.10).
6 • Dry ironing
Set the variable steam control to (fig.11) and set the
temperature to suit the type of material (care points •, ••, •••).
Ironing label Fabric Temperature
control
Synthetic fibres, e.g.
viscose, polyester…
•
Silk, wool
••
Cotton, linen
•••
YELLOW
(pulse)
The soleplate is still too cold for the selected material.
GREEN The soleplate is at the right temperature for the selected
material.
RED
(pulse)
The soleplate is still too hot for the selected material.
AUTO- OFF
(blinking)
The automatic electronic cut-out* is active.
TIP Always spray starch onto the reverse side of the fabric to
be ironed.
IMPORTANT The iron takes longer to cool down than to heat
up. We recommend that you start with fabrics to be ironed at
a low temperature. For mixed fabrics set the temperature for
the most delicate fabric.
* depending on model
DZ9000-11038999469 2/03/06 14:29 Page 6

7
7 • Steam ironing
You can steam iron from temperature setting •• up.The steam
quantity can be adjusted between Smooth Steam (soft steam
continuous diffusion) up to High Pressure steam .
We recommend setting to High Pressure steam only when the iron
is at temperature setting •••.
8 • High Pressure Steam
Your iron is fitted with the new High Pressure Steam system
(fig.13).This technology generates higher steam pressure to enable
the steam to penetrate much faster and further into the fabric.
This way you get excellent results from your ironing.
The steam is emitted in frequent bursts rather than continuously.
The pressure generated may cause a slight noise.This is not a
technical fault!
9 • Shot of Steam
(from temperature setting •• up)
Press the shot of steam button to generate a powerful jet of
steam and remove stubborn creases (fig.14).
10 • Vertical shot of steam
(from temperature setting •• up)
Hold the iron to the vertical and press the shot of steam button
(fig.15) to remove creases from suits, jackets, skirts, hanging
curtains etc.
11 • Spray
Press the spray button to dampen stubborn creases (fig.16).
12 • Anti-Drip system*
It prevents water escaping from the soleplate when the temperature
is too low.
IMPORTANT Leave an interval of 4 seconds between each
shot and wait until the flow of steam is finished before
standing the iron on its heel.
IMPORTANT Never direct the steam at persons or animals!
TIP Hold the iron 10 to 20 centimetres away from the garment
to avoid burning delicate fabrics.
* depending on model
es
g.
DZ9000-11038999469 2/03/06 14:29 Page 7

8
C
se
p
ir
U
W
1
W
c
w
T
t
t
T
c
o
a
Y
a
P
13 • Automatic electronic 3-position shut off
If, although switched on, the appliance is not moved, it will
automatically switch off and the auto off light will blink after
the following intervals (fig.17):
- After 30 sec., if the iron is standing on the soleplate or lying on its side.
- After 8 mins., if the iron is standing on its heel.
AFTER USE
14 • Emptying
Unplug the iron (fig.4), pour away remaining water (fig.18) and set
steam control to .
Open and close the steam control several times (fig.19) to prevent
the drip hole into the steam chamber from furring or blocking up.
15 • Storing
Allow the appliance to cool down before storing the iron standing
on its heel
(fig.20) .
MAINTENANCE AND CLEANING
16 • Anti-scale system
Your iron contains an anti-scale cartridge to reduce scale deposits.
This considerably prolongs the operational life of your iron.
The anti-scale cartridge is an integral part of the water tank and
does not need to be replaced.
17 • Self Clean function
(prolongs the life of the iron)
The Self Clean function flushes dirt and scale particles out of the
steam chamber. Fill the water tank with tap water up to the max
mark and heat the iron to the ••• temperature. Unplug the iron and
hold it over a sink horizontally. Hold the steam control into the Self
IMPORTANT Do not wind the cord around the hot soleplate.
Never store your iron placed down on the soleplate (fig.20).
IMPORTANT Unplug and allow the iron to fully cool down
before maintenance and cleaning.
IMPORTANT Do not use descaling agents, as these damage the
lining of the steam chamber and so may impair the steam function.
*
DZ9000-11038999469 2/03/06 14:29 Page 8