Rowlinson Garden Products SS269E User manual

x 2 drill
Large Log Store
Assembly Instructions
English SS269E
Information
No. Components Qty.
1Floor 2
2Left side panel 1
3Right side panel 1
4Centre panel 1
5Back slat notched 2
6Back slat 18
7Shelf 1
8 Roof panel 2
9Roof top board 2
10 Roof fascia 2
No. Fixing Kit Qty.
11 80mm screws 4
12 63mm screws 4
13 50mm screws 10
14 45mm screws 4
15 40mm nails 96
16 30mm nails 12
Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step by
step guide. The instruction sheet is only
a guide to the assembly. Certain items may
not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people
•Drill all components where indicated
Recommended tools for assembly
•Power drill/screwdriver
•3mm drill bit
•Cross head screwdriver bit
•Tape measure
•Hammer
•Spirit level
•Sharp knife
2022 © Rowlinson Garden Products Ltd
We constantly improve the quality of our products, occasionally
the components may differ from the components shown and are
only correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
If in doubt of any aspect regarding the assembly, use or safety of your log store, please contact us:
Help Line (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
45mm
45mm
80mm
6 . Roof
With the roof panels upside down, secure them together using 2 x 50mm screws. Once secured turn up the right way.
Place the roof onto the main assembly and attach to each side panel by screwing 2 x 45mm screws down through the
roof into the top frames of the side panels. In the middle of the roof, screw 4 x 80mm screws through the roof into the
centre panel.
5 . Roof panels
To each roof panel, position a roof top board so that it overhangs the front edge by 50mm. Secure in place using 6 x
30mm nails. Position the front fascia board underneath the top board and secure to the roof framing. At each end use 2
x 40mm nails. In the middle use only 1 x 40mm nail.
50mm
30mm
40mm
50mm
It may be necessary to drill
pilot holes for all screws in
this section.
Drill
1
2
3
4
5
6
7
8
9
10

3. Shelf
Position the shelf at the desired height between the side and centre panels. Secure in place using 4 x 63mm screws. Screw
through the panel frame in to the ends of the shelf frames as show below.
1. Floor assembly
Place the floor panels upside down, secure them together using 2 x 50mm screws. Once secured turn up the right way.
2. Wall panels
Position the left, right and centre panels as shown. Secure each one in place using 2 x 50mm screws per panel. Screw
through the bottom frames of the panels in to the floor.
Drill
50mm
Drill
It may be necessary to
drill pilot holes for the
screws in this section.
Note:
Attach the right
side panel in
the same way
as the left.
Note:
The shelf can be positioned
in either side of the store.
Important note:
As the shelf is attached
use a spirit level to make
sure it is level from front
to back and side to side.
50mm
50mm
63mm
63mm
Important note:
Align the two notched
slats with the rear
upright of the centre
panel.
40mm
40mm
40mm
40mm
Important note:
The side panels slope down
to the back of the log store.
4. Back slats
Secure the back slats to the back of the log store. Ensure the two slats with notches are at the top. Align each slat with
the slats on the side panels and secure in place using 2 x 40mm nails at each end of each slat. Nail the bottom slats to the
floor using an additional 3 x 40mm nails per slat.
It may be necessary to
drill pilot holes for the
screws in this section.
It may be necessary to
drill pilot holes for the
screws in this section.
Drill