Roxy THE YANG User manual

THE YANG INSTRUCTIONS MANUAL

FEATURES & FUNCTIONS
Time/Date
 •Hours,minutes,andseconddisplayin12Hror24Hrformat.
 •DOW–Datedisplay
Chrono
 •Hundredthsecondsresolution
 •24hourmaximum
Alarm
 •HourandMinuteelds
OtherFeatures:
 •3VDCOperatingVoltage
 •3VDCOperatingVoltage
 •Electro-luminescent(EL)backlight
 •Four(4)buttonsoperation
 •HourlyChime

INPUT/OUTPUT
LCDFullSegmentOn

Flags
INPUT/OUTPUT
ICON NAME ICON NAME
24 24-Hour Format Chime/Keytone
PPM Alarm

SmallDigits
BigDigits
FontTable
INPUT/OUTPUT

MODE LOOP
ModeLoop
TimeofDayMode
Power-On Defaults
Field Value
Time 12:00AM
Date January 1
Day of Week Sunday
Date Format DOW Date
Boundary Conditions
Field Value
Date Format DOW-Date
Hour 1 to 12 (12H), 0-23 (24H)
Minute 0 to 59
Second 0 to 59
Month 1 to 12
Date 1 to 28, 29, 30, 31 (depending on MONTH)

MODE LOOP
TOD Alarm
Chronograph
TOD Setting State: Seconds Set
90 Seconds Timeout
Press [S2]
Press [S2]
Press [S2]
or
2 minutes timeout
TOD Hour Set TOD Minute Set TOD Month Set
TOD Date SetTOD Day Of Week Set
TOD Default
Press [S3]
Press [S2]
Toggle 24Hr Format
Press [S4]
Press [S2]
]3S[sserP
]3S[sserP
]3S[sserP
Press[S3]

NOTES
 1.Afterpoweronreset,thedefaultModetoappearisTOD.All
buttonsareactivethen.
 2.ThesequenceforthemainmodeloopwillstartfromTOD->
Alarm->Chronograph->EntrytoTODSettingStatethenbacktoTOD.
 3.WhileinsideAlarm’sdefaultstateandidlefor90seconds,itwill
returnautomaticallytoTOD.WheninAlarm’ssettingstate,ifidlefor2minutes
thenitwillAuto-returntoTOD.
MODE LOOP

 4.InTODSettingState,thefollowingbuttonfunctionsareapplied:
-[S2]Mode/Set,exitfromsettingstate.
-[S3]Reset,movefromcurrenteldtothenexteld.
-[S4]ST/SP,adjustthevalueoftheeldinincrementingorder,  
wrapstothelowestpossiblewhenitreachestothehighestvalue.
Exceptforthesecondseldwhereitwillberesetto00whenbeing 
adjusted..
-[S1]EL,nospecialfunctionexceptforturningELon.
 5.TheELwillactivateduringbuttonpressandwillstayfor3
secondsafterthekeyrelease.
MODE LOOP

ChronographMode
CHRONOGRAPH MODE
Power-On Defaults
Field Value
Chrono 00:00:00
Status RESET
Boundary Conditions
Field Value
Hour 0 – 23
Minute 0 – 59
Second 0 – 59

MODE CHRONOMETRE
Chrono Reset State
STOP State
T < 60 minutes T >= 60 minutes
Running State
Press [S4]
Press [S4]
Take Split
Press [S3]
Running State
Press [S3] Assuming have 10
seconds elapsed
time
Running State
Press [S4]
Continue run...
Continue run plus
elapsed time (Split)
STOP Split
[S4]
Display Split Time
Chrono Reset State
Press [S3]
Press [S3]
Press [S3]
Runout: Stop State
Press [S3]

NOTES
1.ElapsedTimeMeasurement
a.Press[S4]buttonintheChronographresetstatetostartmeasu 
rement
b.Press[S4]buttontostopmeasurementandpress[S4]againto 
continuerun.
c.DuringStopState,pressing[S3]willresetthecounter.
2.SplitTimeMeasurement
a.Duringrunningstate,pressing[S3]willtakesplittime.
b.WhileinSplittimedisplay,pressing[S3]willgobacktoChrono 
graphdisplay.
CHRONOGRAPH MODE

c.Press[S3]buttontonalizethesplittimedisplaywiththechro 
nographintheSplitStoopState.
d.Press[S3]buttontoresetChronowhileinStopstate.
3.Chronographresolutionis23:59:59.99s.Therearetwosetsofdisplaydepen-
dingonthecountervalue.
a.MM:SS.hh,ifthecounterislessthananhour.
b.HH:MM.ss,ifthecounterisgreaterthanorequaltoonehour.
c.Duringrunningstate,thecolonisblinking.
MODE CHRONOMETRE

ALARMMode
ALARM MODE
Power-On Defaults
Field Value
Alarm 12:00 AM
Alarm Status OFF
Chime Status OFF
Frequency Daily
Boundary Conditions
Field Value
Hour 12H: 12AM to 11PM, 24H: 0 to 23
Minute 0 – 59

ALARM MODE
e
Alarm
Alarm On Chime On Alarm On and Chime On
Press [S4]
Press [S4] Press [S4]
Press [S4] -> disable all
Alarm Hour Set Alarm Minute Set
Press [S3]
Press [S3]
Press [S3]
Alarm On
Press [S2]

NOTES
 1.ThisisthedefaultstateofALARM.
 2.Whileindefaultmode,thefollowingsequencewillupdateAlarm
andChimeIcons.
->Press[S4],enablestheAlarm,press[S4]disarmedalarmandthenenable
Chime,andnallypress[S4]againwillarmbothAlarmandChine.Another
pressof[S4]willdisableAlarmandChimethistime.
 3.DuringAlarmdefaultstate,pressing[S3]willenterintosetting
statewherethehoureldisblinkingandtheAlarmIconisautomaticallyarmed.
ALARM MODE

Pressing[S4]willadjustthevalueincrementally.Pressingthe[S3]buttonwill
movetothenexteld.SettingsequenceisfromHOUR->MINUTES->HOUR.Fast
scanningisavailableduringsettingstate.
 4.Thealarmwillgeneratesoundfor20secondswhenitisactiva-
ted.
 5.Thealarmiconwhenarmedisvisibletoallmodes.
 6.Whileindefaultstate,ifitisidlefor2minutesthenitwillreturn
backtoTOD(auto-return).Duringsettingstate,ifitisidlefor90seconds,itwill
alsoexitbacktoTOD.
ALARM MODE

GlobalRules
A.ELHandlingandOperations
•ELwillturnonduringbuttonpressandwillstayonfor3secondsafter
buttonrelease.WhileELisON,itcannotbecancelledbyanybuttonpress.IfEL
buttonispressedduringELON,the3sdelaywillberesetafterkeyrelease.
•ELcanbeactivatedinanymode’sstate.
B.KeyHandlingandOperations
•NoPressandHoldoperationexceptforfastsetting.
•FastSettingwillbeonduringsettingstateifheldfor2s.
•WhenfastsettingisON,itsteps8timespersecond.
•Atanysettingstate,nokeyoperationfor90secondswillsavechangesand
exitsettingbacktoTOD.
GLOBAL RULES

C.Display/Blinking
•Blinkingofsettingitemswillbetwicepersecond.
D.ToneandAlerts
Application
GLOBAL RULES
Chime
o
Double Short Beep tone
Keytone
o
Single Short Beep tone
Alarm
o
Double beep tone for 20 seconds.