Royal Aircraft S.E.5a FIGHTER User manual

O1
O3
O2
O4
O5
O6
A9
A28
A11
A15
A16 A17
A18
A19
A20
A21
A22 A23
A24 A25
A26
A27
A12
A10
A14
A13
A2
A1 A3 A4
A5
A6 A7 A8
Brushless Motor Parts
F1
F2
F4 F5 F6
F3
F7
F8
G1
G2
G3
G4
G5
G6
G7 G8
G9
G10
G12
G11
G13 G14
E1
E2
E3
E4
D5
D2
D6D1
D3 D4
D8 D8 D9
D7
C1 C2
C7C6
C5
C3
C4
B1
B2
ROYAL AIRCRAFT FACTORY S.E.5a FIGHTER
BALSAWOOD MINI AIRPLANE INSTRUCTION MANUAL
Balsawood Pieces and Accessories
Installation of Fuselage
Tools Needed
Specification
Painting Stickers
A6
A2
A9
A23 C5
C4 C3 D1
C7
A7
A13
A1
A8
A3
A22
E1
E1
C2
E4
D3
A20 G8
1.Take out the A1、A2、A3、A6、A7、A8、A9、A13、A22、A23、
C3、C4、C5、C7、D1 from the board, assemble the frame
parts as below picture, use glue to stick the junction.
5.Stick tail cover F1 (Bend and stick before moistening
with the water.)
Note: This airplane has brush version and brushless
version for your choice, above is the installation of brush
version.Below is the installation way of brushless version.
(Red parts are the difference of this two versions.)
2.Take out E1 from the board, assemble the cover over
the fuselage frame in pre-cut hole.(For the bend parts,
please paste it before moistening with the water.)
3.Take out C2、D3、E4 from the board, install the bottom cover
over the fuselage frame, use glue to stick the junction, assemble
A20 at the same time, put the magnet (G8) into the inside of
preformed hole .
4.Take out C6、D2 from the board, assemble the cabin
cover as below picture, and insert magnet (G8),
Note:Here magnet is attractable with A20.
O3 O5
O4
F1
Wingspan:378mm
Length:330mm
Flying Weight:≈40g
Suggested Prop:4530-5030
Brushed motor
Suggested Motor:DEPS7 brushed motor
Suggested ESC/Servo/RX:DSMⅡ 3in1 board
Suggested BATT:1S 100-200mah
Brushless motor
Suggested Motor:1104 KV3700
Suggested ESC:1S 5A
Suggested Servo:2g servoX2
Suggested BATT:1S 200-250mah
Suggested Radio≥3CH
H1
H2
G8
C6
D2
C.G
25mm
The Position of CG

3.Take out A18 from the board, insert the bracket, and
take out D6 to stick on the bracket.
9.Cut open the reserved hole in the aft fuselage, insert
servo connecting link (G1).
G14 pass through the horn (A17), then connect G14 and
servo horn connecting link, use heat-shrinkable tubing
to seal them together.
A18
F2
Installation of Wing
6.Stick tail parts F7, sand it to be integrated with
fuselage after the glue dried.
7.Take out E3、F4 from the board, assemble the nose.
8.Take out A4、A11、A15、D7、E2、F5 from the board. Assem-
ble engine cover as below picture.(Bend and stick D7
before moistening with the water.)
1.Take out B1、B2、H1、H2 from the board, assemble
the wing as below picture.
2.Cut open the reserved groove at the side of the
fuselage, install the wing bracket, and fix with screws.
9.Plug the engine cover into the fuselage, assemble the
emulational parts, complete the installation of fuselage
part.
F7
E3 F4
A11
A28
screws
D7 F5
E2
G4
A15
A4
emulational engine
B1
H1
H2
H1
B2
B1
F8 F6
F3
8.Cut open the reserved groove in the aft fuselage, and
install tail wing, use glue to stick the junction.
Keep the tail wing vertical and horizontal when sticking.
4.Install top wing B1, use glue to stick the junction.
5.Take out A19 from the board, insert fuselage as below
picture, then install under wing H1, use glue to stick the
junction.
6.Take out A12 from the board, install the top wing and
under wing as below pictures, use glue to stick the
junction, and install emulational parts.
*Brush version (With DSM 3 in 1 Board) Installation
*Brushless version (With 2g servo) Installation
Cut open the reserved hole when install the servo.
7.Take out A17、Ｃ1、D5、A5 from the board, stick A5 on
the rudder, and stick hinge (G12) on the red frame parts.
D6
A19
A12
emulational machine gun
emulational windshield
A25
A26
A21 G13
G5
A27
A24
C1
A5
A17
A17
D5
hinge G12
Installation of Landing Gear and wheels
Installation of Motor and Electronics
1.Take out A10、A14、D4, use screw to connect A10、
A14 into landing gear,plug the landing gear into the
bayonet of the cabin, glue together.
2.Take out D8、D9 from the board, stick hub as below
picture, cover G11 at the hub.
D4
G3
screws
A10 A10
A14
D8
D8
G11
D9
G6
heat-shrink tube
heat-shrink tube
heat-shrinkable
Fasten the servo at
the 3in1 board
O6
O6
O1