RSA Lighting Combolight MR11 User manual

DESCRIPTION Catalog # Type
Project
Comments Date
Prepared by
SPECIFICATION FEATURES
www.cooperlighting.com
Thermal
Protector
5.75”
3.88”
7.75”
14.07”
14.11”
18.20”
13.19”
Integral Low Voltage
Transformers
3.88”
10.24”
Perforated
Meshplate
45º x 45º
Adjust
Double
Gimbal
A ... Housing
Housing, junction box & trimless
meshplate assembly are all steel
construction. Perforated meshplate allows
for trimless installation in drywall/plaster
ceilings by allowing the ceiling’s mudding
compound to be applied right up to the
edge of the fixture opening. Includes
a beveled “knife-edge” lips to ensure a
clean edge. Can accommodate 0.50” to
1.25” ceiling thickness. Optional Chicago
Plenum configuration available.
B ... System Protection:
Thermal protection provided to guard
against overheating and misuse of
insulation over and around fixture. Vent
holes in housing provide cooler operation.
C... Junction Box
Junction Box is UL listed for through
branch wiring, 6 #12 90º C supply
conductors or 60º C for end of run. The
fixture is also UL listed as ‘access above
ceiling not required’.
D... Electrical
Electrical accessible through ceiling
opening. J-Box located on the side wall
of the housing behind removable access
doors. Integral electronic or magnetic
low voltage transformers on individually
removable “trays” for easy maintenance.
May also be configured for remote power.
E ... Lamps
Two (2) 12V MR11 lamps mounted in
adjustable double gimbals. Lamp holders
are individually removable and may be re-
gressed 1” for additional cut-off. Lamp can
accept up to three optical accessories (i.e.
lens + hex louver + snoot). 45º x 45º locking
lamp adjustment. Beveled-edge lamp ring
is secured with threadless, bayonet action.
Optional retractable arm is available for
lamp pulldown and extreme aiming.
F ... Mounting
Butterfly Brackets accept 1/2” EMT,
C Channel, Tbar fasteners, and bar
hangers. Four tabs on housing for
securing to structure. Perforated flaps
along housing sides for securing trimless
insert to fixture and drywall.
G... Labels
cULus listed for non-type IC
applications, suitable for use in damp
locations.
Ceiling Cut-Out: 4.67” x 8.55”
COMBOLIGHT®
Next Generation
Recessed
Multi-Lamp Fixture
Two (2) Light
12V MR11
New Construction
Housing
Trimless
ORDERING INFORMATION
An adjustable Multi-lamp Recessed fixture for trimless installation suitable for
downlighting and accent applications. Utilizes TWO (2) 12V MR11 lamps.
For new construction applications. Insulation must be kept 3” from all sides
and at least 1” above the housing.
Specifications and Dimensions subject to change without notice.
RSA Lighting • 7945 Orion Ave. • Van Nuys, CA 91406 • 818-349-3030 • FAX [phone]
rev 121107
Configuration
C2 =COMBOLIGHT
Recessed Two (2) Light
Housing
N =New Construction
C =Chicago Plenum
C2 N N
Lamp Type / Wattage Label
020M11 =20 Watt max. MR11 12V
035M11 =35 Watt max. MR11 12V
Power Supply
E =Electronic Low Voltage
Transformer
M =Magnetic Low Voltage
Transformer
Power Supply
Voltage
1 =120V
2 =277V
Lamp Mechanism
G =Double Gimbal
R =Retractable Double Gimbal
Trim Insert Finish
N =Trimless
Trim Insert
N =Trimless
Housing Interior/Electrical Door/Sleeve
Finish
W =White
B =Black
S =Industrial Silver
NOTES:
De-Rated wattage labels are available.
12V Primary voltage is available.